• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.1
• /
• pp.97-103
• /
• 2003

Numerical research has been done for the transverse jet behind a rearward-facings step in turbulent supersonic flow without chemical reaction. Purpose of transverse jet is to enhance mixing of the fuel in the combustor. Two-dimensional unsteady flowfields generated by slot injection into supersonic flow are numerically simulated with the Navier-Stokes equations with two-equation k-$\varepsilon$ turbulence model. Numerical method is used high-order upwind TVD scheme. Eight cases are computed for different slot momentum flux ratios and slot position at downstream of the step. The flow is very similar to the cavity flow, because the jet acts as an obstacle. The numerical results thus show the periodic phenomenon.

• Journal of Advanced Navigation Technology
• /
• v.14 no.4
• /
• pp.479-488
• /
• 2010

The aim of this paper is to research the change in the turbulent flow and the AOA occurred by the wind perpendicular to the direction of runway according to the three-dimensional numerical analysis. The maximum amplitude of AOA variation on runway reached $6^{\circ}$ within 1 second because of the wake formed by the constructions in the vicinity of the airport. The overall effects appeared in aperiodic forms. It was also observed the rapid flow generated between the buildings shifted into the existing wake and eventually merged with it. It is expected thai the strong wake will cause instability during takeoff and landing.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.5
• /
• pp.1322-1329
• /
• 1994

The effect of thermal stratification on the stratified flow past a circular cylinder was examined in a wind tunnel. Turbulent intensities, the rms values of temperature and turbulent convective heat flux as well as the velocity and temperature profiles in the cylinder wake with a strong thermal gradient of $200^{\circ}C/m$ were measured by using a hot-wire and cold-wire combination probe. It is found that the temperature field affects as an active contaminant, so that the vertical growth of vortical structure is suppressed and the strouhal number decreases with increasing the extent of stratification. And also, the wake structure can not sustain their symmetricity about the wake centerline and vertical turbulent motion dissipates faster than that of the neutral case when such a strong thermal gradient is superimposed. It is evident that the turbulent mixing in the upper half section is stronger than that of the lower of the wake in a stably stratified flow because the turbulent intensities and convective heat flux in the upper half section are larger than those of the lower half of the wake.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.12 no.2
• /
• pp.33-39
• /
• 2008

To improve the mixing efficiency and to reduce the pressure loss, it is needed to develope a new mixing device for supersonic combustion. The vent mixer is introduced as the new supersonic fuel-air mixer. Computational analyses, that include pressure profile, density contour, and streamline tracing, have been carried out. The expansion wave generates at the end of the extended upper wall of the mixer. And it reduces the shock wave from the hole. Incoming air flow through the hole makes several recirculation regions which increase the mixing efficiency, and the separation region at the downward wall expends the boundary layer which reduces the pressure loss.

• Journal of the Society of Naval Architects of Korea
• /
• v.45 no.4
• /
• pp.353-360
• /
• 2008

A numerical model for the analysis of the marine propeller including wake roll-up is presented. In this study, we apply a higher-order panel method, which is based on a B-spine representation for both generations of the propeller geometry and hydrodynamic solutions, to predict the flow around the propeller blades. The present model is validated by comparison of the experimental measurements. The results show that the present method is able to predict the improved pressure distributions on the blade surface, especially very close to propeller tip regions, where other panel methods without the wake roll-up model give erroneous results.

• Proceeding of EDISON Challenge
• /
• 2012.04a
• /
• pp.81-84
• /
• 2012

항공기 설계에서 중요한 해석 대상중의 하나인 에어포일 NACA 4412 형상을 2차원 난류 점성유동으로 접근하여 일정 받음각에 따른 유동 현상을 실험 결과와 비교해 보았다. 또한, 역압력구배, 유동 박리, 와류 등의 현상이 어디에서 어떻게 생성되는지 해석을 통하여 분석해 보았다.

• Proceeding of EDISON Challenge
• /
• 2016.03a
• /
• pp.622-624
• /
• 2016

교량의 케이블이나 송전선같은 원형 구조물들은 유동의 불안정성에 의해 물체 후방에 Vortex가 발생한다. 이렇게 발생한 Vortex는 구조물에 진동과 소음을 발생시키게 된다. 본 연구에서는 이러한 원형 구조물들의 배열에 따른 해석을 진행하였다. 같은 크기의 두 원형 실린더를 주 유동 방향으로 정렬시킨 배열을 EDISON 전산열유체 시스템을 이용하여 해석하였다. 두 원형 실린더의 중심의 거리를 1.5 D부터 5 D까지 변화시켜가며 거리에 따른 각 실린더의 Drag coefficient에 초점을 맞추어 연구를 진행하였다. 두 원형 실린더 사이의 거리가 감소할수록 후류 쪽에 위치한 실린더의 Drag coefficient의 값이 감소하는 양상을 보였다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.11 no.6
• /
• pp.877-883
• /
• 1987

A new improved inviscid separation model to calculate the mean flow past circular cylinders is proposed. The wake region is modeled by a pair of vortex sheets which emerge from the separation points and are allowed to move freely with the local stream. The vortex strength assumes a constant value for some initial distance which is related to the pressure drag and gradually decreases to zero as the sheet moves farther away from the body. This vorticity distribution automatically takes care of the length parameter which has been one of the deficiencies in the existing models. The procedure is tested against various experimental data and the agreement is quite good for both sub and super-critical regimes. The comparison with an existing model is also given.

• Journal of the Society of Naval Architects of Korea
• /
• v.34 no.1
• /
• pp.24-40
• /
• 1997

Horseshoe vortices generated around the juncture between the ship and her appendages often lower a performance of the ship by increasing the appendage drag and making a non-uniform wake on the propeller plane. This paper investigates numerically how the fillet around the juncture of the leading edge influences the juncture flow and the appendage drag. Computation has been made by solving Navier-Stokes equations with MAC method and the flows are at the Reynolds number of 5,000. Five fillets with different height-breath ratios and curvatures are chosen as test models to find out the effects of the shape of fillets on the appendage drag and wake. Computational results show that fillets with a smaller height-breath ratio and/or with a concave curvature has smaller appendage drag and more uniform wake.

• Journal of the Korean Institute of Gas
• /
• v.16 no.1
• /
• pp.1-7
• /
• 2012

The present study has been carried out to analyze the flow characteristics in the inlet expasion duct of a heat recovery steam generator by using numerical flow analysis. The inlet of HRSG corresponds the outlet of gas turbine exit and the flow after gas turbine has strong swirl flow and turbulence. The inlet flow condition of HRSG should be included the exit flow characteristics of gas turbine. The present numerical analysis adopted the flow analysis result of gas turbine exit flow as a inlet flow condition of HRSG analysis. Because the flow characteristics in the inlet duct of the tube bank is strongly related to the performance of a HRSG, it is most important for the optimal design of HGSG to understanding the flow phenomena in the inlet duct of HRSG. From the present study, the position of breakpoint in the inlet expansion duct should be lower than the reference breakpoint position for the optimal flow uniformity before the tube bank.