• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.2
• /
• pp.186-193
• /
• 2005

This paper presents a strategy to drive built in-type spindle induction motor which is used as CNC(Computer Numerical Control) in the industry. Gopinath model flux estimator which is composed of current model to be profitable in the low speed range and voltage model to be profitable in the high speed range is used for rotor flux estimation. Moreover this paper presents to drive the spindle motor in the high speed range by using the flux weakening control. High speed operation of spindle motor in the field weakening region is verified through simulations and experiments.

• Journal of Biosystems Engineering
• /
• v.25 no.5
• /
• pp.351-358
• /
• 2000

This study was conducted to develop a speed control system of a DC motor which drove a barley seeder mounted on a combine harvester. Barley seeder mounted on a combine has been known to reduce labor and cost of barley cultivation. However, development of the seeder has been unsuccessful because the combine, a dedicated rice and barley harvester has not enough space and proper power take-off for barley seeder. To develop a barley seeder, small powered motor speed controller was required. A proximity sensor for detecting working speed of the combine and a programmable one board microprocessor was used to develope a control system. Motor parameters and motor constant, relationship between seeding rate, motor speed, groove volumes of a tested roller, torque were measured. The proximity sensor sent a frequency signal to the microprocessor. In laboratory experiments, the excitation voltage of the motor was shown not to be proportional to the size of pulse width (duty ratio). A table transforming frequency signal, that represented for working speed to proper pulse width was developed from seeding rate experiments. However, seeding rate at low frequency signal was not proportional to the working speed. Seeding rate control proportional to the frequency signal was achieved by shifting of the frequency signal.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1738-1739
• /
• 2007

초음파 모터는 고정자와 회전자를 가압마찰하기 위해서 내부에 원형 판 스프링을 이용하고 있다. 출력 토크를 높이기 위해서 이러한 내부 스프링의 강도를 크게 하면 홀딩 토크 역시 커지게 된다. 이로 인하여 기동 시 많은 전류가 소모되며 일반적인 구동 파라미터에 따른 속도 특성 등 기존의 스프링 강도를 지닌 초음파모터(모델명 : 신생공업사(일) USR60-s1)의 특성과는 전혀 다른 특성을 보인다. 본 논문에서는 스프링이 강화된 새로운 타입의 초음파모터(모델명 : 신생공업사(일) USR60-s3)를 가지고 무부하 시의 속도 특성을 실험하였다. 이를 위해 FPGA를 이용해서 디지털 다중 초음파 모터 제어기를 설계하였고, 2상입력 전원의 주파수, 위상차, 주파수-위상차 다중 파라미터 등을 조절하면서 무부하 속도 특성을 측정하였다. 그 결과 홀딩토크가 강화된 초음파 모터의 경우 일반적인 기존 초음파 모터와 비교했을 때 전혀 다른 특성을 보이고, 위상차-주파수 다중 파라미터 조절방식이 조절방식임을 보인다.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.11
• /
• pp.43-51
• /
• 2021

A robust tracking controller design was developed for a rotary motion control system. The friction force versus the angular velocity was measured and modeled as a combination of linear and nonlinear components. By adding a model-based friction compensator to a nominal proportional-integral-derivative controller, it was possible to build a simulated control system model that agreed well with the experimental results. A zero-phase error tracking controller was selected as the feedforward tracking controller and implemented based on the estimated closed-loop transfer function. To provide robustness against external disturbances and modeling uncertainties, a disturbance observer was added in the position feedback loop. The performance improvement of the overall tracking controller structure was verified through simulations and experiments.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.7
• /
• pp.275-282
• /
• 2018

Mountain trams are an environmental-friendly transportation system that run wirelessly on an embedded track constructed on previous mountain roads, and can run despite the frozen road. On the other hand, there is some difficulty on sharp and steep tracks. In this study, after possible technical problems were defined in mountain trams running on a sharp and steep track, the design solutions for the interface structure of bogie and carbody were proposed. In addition, a prototype was made and its performance was tested to verify the solutions. Because the difference in the distance of the inner and outer rails on a sharp curve is severe enough to interrupt running, independent rotating wheels with different angular speeds were developed and applied. To prevent derailment due to the large attack angle and lateral force caused by the previous vehicle of 2bogie-and-1carbody on the sharp curve, a vehicle with 1bogie-and-1carbody was designed and applied. A prototype vehicle of 1bogie-and-1carbody with independent rotating wheels was made to improve the performance during the test running on a small track. A coupler was designed to absorb the large rotations of 3 degrees-of-freedom between the carbodies of a mountain tram running on the steep curved track. After a small scale prototype was made, the performance was verified by a function test.

• Journal of the Korea Convergence Society
• /
• v.11 no.11
• /
• pp.195-201
• /
• 2020

This paper implemented quadcopter-type drone system and proposed the heuristic method for obtaining the optimum gain coefficients in order to minimize the settling time. Control system for quadcopter posture stabilization reads the posture data from accelerator and gyro sensor, revises the original posture data using Mahony filter, and drives 4 DC motors using PID controller. The first step of the proposed method is to obtain the gain coefficients using the Ziegler-Nichols method, and then determine the optimum gain coefficients using the heuristic method at the next 3 steps. The experimental result shows that the maximum overshoot decreases from 44.3 to 29.8 degrees and the settling time decreases from 2.6 to 1.7 seconds compared to the Ziegler-Nichols method. Therefore, we proved that the proposed method works well in quadcopter flight system with high motor noise while reducing trial and error to obtain the optimal PID gain coefficients.

• The korean journal of orthodontics
• /
• v.37 no.1 s.120
• /
• pp.5-15
• /
• 2007

Objective: The purpose of this study was to evaluate the mechanical performance of mini-screws during insertion into artificial bone with use of the driving torque tester (Biomaterials Korea, Seoul, Korea), as well as testing of Pull-out Strength (POS). Methods: Experimental bone blocks with different cortical bone thickness were used as specimens. Three modules of commercially available drill-free type mini-screws (Type A; pure cylindrical type, Biomaterials Korea, Seoul, Korea, Type B; partially cylindrical type, Jeil Medical, Seoul, Korea, Type C; combination type of cylindrical and tapered portions, Ortholution, Seoul, Korea), were used. Results: Difference in the cortical bone thickness had little effect on the maximum insertion torque (MIT) in Type A mini-screws. But in Type B and C, MIT increased as the cortical bone thickness Increased. MIT of Type C was highest in all situations, then Type B and Type A in order. Type C showed lower POS than Type A or B in all situations. There were statistically significant correlations between cortical bone thickness and MIT, and POS for each type of the mini-screws. Conclusion: Since different screw designs showed different insertion torques with increases in cortical bone thickness, the best suitable screw design should be selected according to the different cortical thicknesses at the implant sites.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.80-80
• /
• 2017

국내에서 대부분 생산되는 사료(사일리지) 수확 작업은 베일 생산 및 비닐 래핑 작업이 독립적으로 수행되고 있어서 비효율적이다. 본 연구에서 개발한 조사료 수확기는 수집, 롤링, 베일 네트 생성, 래핑, 래핑 종료 및 베일 방출작업을 통합적으로 수행하도록 설계-제작하였다. 통합형 다목적 조사료수확기의 설계는 3D 디자인 툴 (CATIA V5R18)을 이용하여 실시하였으며, 기구부 23 파트 어셈블리, 전기제어 어셈블리, 유압요소기술을 통합하여 통합시작기를 제작하였다. 기초 프레임, 오거장치파트, 픽업장치파트, 하부롤러파트, 상부롤러파트, 하부 프레임 및 주행부 파트, 래핑회전파트, 롤러부 구동 동력부, 유압파트, 전기제어파트, 드로우바파트, 체결 및 컨트롤러 파트 등 25개 파트로 구성되어 있다. 본 연구에서 개발한 시작기의 견인력 및 소요동력 분석은 선행 연구에서 사용한 Brixius (1987) 제안 모델을 체택하여 분석하였다. 이 Brixius 제안 모델은 견인력 예측에서 토양변수 및 토양강도 특성을 나타내는 원추지수 (Cone Index, CI)를 이용하여 트랙터의 견인력 예측에 사용하였다. 또한 트랙터-조사료수확기 시스템의 소요 견인력을 예측하는데 있어, 트랙터-조사료수확기 시스템이 운용되는 토양조건과 트랙터의 마력에 따른 소요 견인력 특성을 분석하기 위해 대표적으로 3수준의 토양조건 (CI: 356 kPa, 543 kPa, 1,429 kPa)을 적용하였으며, 베일의 개당 최대무게는 최고 수준인 옥수수 기준으로 800 kgf를 적용하였다. 본 연구에서 적용된 3수준의 CI 조건은 연구팀에서 선행연구과정 (토양특성에 따른 최적 경운작업 시스템 개발, 2006)에서 분석한 전국 10개 지역의 33개 지점의 경반층 CI지수의 측정범위인 1,050-3,170 kPa에 대해 견인력이 많이 소요되는 열악한 조건 수준을 적용하였다. 각 작업에 사용된 소요동력은 베일 작업시 (ASABE D497.7, 2011) 그리고 래핑작업시 (Zhortuylov et al., 2013)를 사용하였으며 두 소요마력을 트랙터-조사료 수확기 시스템의 필요 소요마력의 합계로 계산하였다. 트랙터-조사료수확기 시스템의 최소 소요 동력, 차축 소요 동력과 PTO 소요 동력을 Zoz and Grisso (2003)을 이용하여 계산하였다. 연구에서는 기본적으로 ASAE의 작업속도 및 작업효율을 적용하였는데, 적용된 조사료수확기의 현장 작업효율은 60-86%의 범위이고 일반적으로 70%를 적용하고 이때 작업속도는 2.5-8.0 km/h이며 전형적으로 5.0 km/h를 기준하고 있다. 자주식 (SP; sief-propelled machine) 조사료수확기의 경우 작업속도가 2.5-10.0 km/h의 범위에서 작업효율은 60-85% 범위이다. 적용되는 조사료 수확기의 작업효율인 60-85% 범위에서 일반적으로 적용되는 작업효율인 70%를 적용하면 트랙터의 소요동력은 95hp를 적정 작업환경으로 하였다.

• The KSFM Journal of Fluid Machinery
• /
• v.19 no.6
• /
• pp.50-54
• /
• 2016

The performance of a scroll expander is the most important factor for the efficiency of small scale Organic Rankine cycle waste heat power generation systems. In this research, a scroll compressor was purchased and operated in reverse to function as a scroll expander. With air as a working fluid, a series of performance test were conducted on this expander by varying the inlet and outlet pressure. Secondly, We have tested through 2000 to 3500 rpm rotational speed to find the maximum power and efficiency of the expander. And last, It was observed in the initial experiments that the design of the expander's orbiting scroll wrap partially blocked the fluid intake which may have caused unnecessary flow resistance. To verify this theory, a small part of the scroll wrap was removed and the performance test was redone. It was observed that the lower back pressure assure the higher efficiency and power of expander and the rotational speed that shows maximum adiabetic efficiency of scroll expander is 69% at 2500 rpm. And by modified wrap of the scroll, we could get volume flow rate for 13% to 19% and power for 5% to 18% increased. But the maximum efficiency of the modified scroll was decreased 8%.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.11
• /
• pp.6446-6451
• /
• 2014

Pneumatic motors are quite attractive for many applications because of their competitive price, light-weight, easy assembly, safety in hazardous areas as well as other features, such as a good force/weight ratio and operation in exceptionally harsh environments. In contrast to these advantages, pneumatic motors have limited use in applications, particularly those requiring a fast and precise response. These undesirable characteristics are due to the high compressibility of air and from the nonlinearities in pneumatic systems. This paper presents the sliding mode controller based on 3-loop(SMCB3L), which increases the load stiffness to control the rotation angle of a pneumatic motor. The characteristics for the step responses and load disturbances of the proposed controller were compared with the conventional PID controller. The experimental results showed that a properly designed SMCB3L is capable of high positioning accuracy within ${\pm}0.05mm$. Furthermore, the load stiffness of the SMCB3L can be improved 3.5 fold compared to that of PID controllers.