• Journal of the Korean Geotechnical Society
• /
• v.32 no.7
• /
• pp.25-34
• /
• 2016

Recently, in Korea, problems related with unstability of slope or sinkhole in urban area due to erosion of compacted granite soil which was used as a backfill or embankment material have been treated as important issues. Small hole might develop inside of backfill area due to erosion of not only weathered granite soil but also clay, silt, fine sand size particles when underground water flows. Once erosion starts in a soil mass, erosion rate increases gradually to cause rapid destruction. In this study, a rotating cylinder test (RCT) was performed to evaluate the hydraulic resistance characteristics of compacted weathered granite soil under various relative densities and preconsolidation pressures. Meanwhile, an image analysis method was introduced to analyze radius of irregularly eroded sample. It was found that image analysis is an effective means of minimizing the error in calculating a critical shear stress and threshold shear stress on the irregularly eroded sample. Furthermore, in general, hydraulic resistance capacity increases with the increase of relative density and preconsolidation pressure.

• Journal of the Korean Magnetics Society
• /
• v.23 no.6
• /
• pp.193-199
• /
• 2013

The regional distribution of magnetic isotropy depending on the post annealing condition for the dual-type structure GMR-SV (giant magnetoresistance-spin valve) of NiFe/Cu/NiFe/IrMn/NiFe/Cu/NiFe multilayer was investigated. The rotation of in-plane ferromagnetic layer induced by controlment of the post annealing temperature inside of the vacuum chamber. The magnetoresistive curves of a dual-type IrMn based GMR-SV depending on the direction of the magnetization easy axis of the free layer and the pinned layer are measured by between $0^{\circ}$ and $360^{\circ}$ angles for the applied fields. The optimum annealing temperature having a steady and isotropy magnetic sensitivity of 1.52 %/Oe was $107^{\circ}C$ in the rotational section of $0{\sim}90^{\circ}$. By investigating the switching process of magnetization for an arbitrary measuring direction, the in-plane orthogonal magnetization for the dual-type GMR-SV multilayer can be used by a high sensitive biosensor for detection of magnetized micro-beads.

• Journal of the Institute of Electronics Engineers of Korea TE
• /
• v.42 no.1
• /
• pp.29-34
• /
• 2005

The wound induction motor can provide high starting torque and reduced starting current simultaneously by inserting large resistor externally when starting. And this technique is one of the well known methods among the induction motor starting methods and generally used for heavy load starting such as crane and cement factories. The conventional PI controller has been widely used in industrial application due to the simple control algorithm and is generally used for control of current torque, position, and speed for the wound induction motor drive system. However, the conventional control system for wound induction motor may result in poor performance because sensors have to be used but are often limited by the environmental condition. Recently, to overcome these problems, many sensorless vector control methods for the wound induction motor have been studied. This paper presents a MRAS method for sensorless vector control of the wound induction motor drive. In the conventional MRAS method, in low frequency, the stator resistance variation may result in poor performance. Therefore, this paper presents a MRAS method with stator and rotor resistance tuning for sensorless vector control of the wound induction motor to overcome several shortages of the conventional MRAS caused by parameter variation and to enhance the robustness of the sensorless vector control. The validity and effectiveness of the proposed method is verified through digital simulation.

• Geophysics and Geophysical Exploration
• /
• v.25 no.1
• /
• pp.26-37
• /
• 2022

Recently, multiple methods using small aircraft for geophysical exploration have been suggested as a result of the development of information and communication technology. In this study, we introduce the hybrid unmanned aircraft electromagnetic system of the Korea Institute of Geosciences and Mineral resources, which is under development. Additionally, data processing and interpretation methods are suggested via the analysis of datasets obtained using the system under development to verify the system. Because the system uses a three-component receiver hanging from a drone, the effects of rotation on the obtained data are significant and were therefore corrected using a rotation matrix. During the survey, the heights of the source and the receiver and their offsets vary in real time and the measured data are contaminated with noise. The noise makes it difficult to interpret the data using the conventional method. Therefore, we developed a recurrent neural network (RNN) model to enable rapid predictions of the apparent resistivity using magnetic field data. Field data noise is included in the training datasets of the RNN model to improve its performance on noise-contaminated field data. Compared with the results of the electrical resistivity survey, the trained RNN model predicted similar apparent resistivities for the test field dataset.

• The Korean Journal of Rheology
• /
• v.11 no.1
• /
• pp.57-65
• /
• 1999

In order to measure yield stress of PIM feedstocks simply and effectively, a yield stress measuring technique was developed by a vane method. The vane method had an advantage that there was no wall-slip, while it had a drawback that it could not measure viscosity change at various shear rates. A Newtonian fluid was tested for the appropriateness of the measuring technique. The end effect of a vane was checked to produce an acceptable error. The torque peak has been considered to be developed at yielding of non-Newtonian fluids with yield stress. However, it was influenced very much by control system of the instrument so that the torque value at the stable region was taken to calculate yield stress. Torque at zero rotational speed was obtained by extrapolating the torque values at various speeds to remove the effect of the rotational drag. As general verification, yield stress of feedstocks made of Tungsten carbide powder with wax-based binder was measured at different temperatures and various powder concentrations.

• Journal of Advanced Navigation Technology
• /
• v.16 no.6
• /
• pp.1005-1013
• /
• 2012

In this paper, the induction motor in indirect vector control method modeling, from indirect vector control method it undergoes an influence to the $1/{\tau}$. When changing a rotor resistance because being like this quality Matlab/Simulink where it will make what kind of effect in speed presumption it led proposed control system used microprosser TMS320C31 DSP for high speed processing. The effectiveness of the proposed system is verified by simulation and experimental results. This result shows highly characteristic speed estimation and robust character of load regulation. and the flux which it follows in change of parameter and speed presumption it was under simulation and get the good result which it comes to get it analyzed.

• Journal of the Korean Chemical Society
• /
• v.11 no.3
• /
• pp.81-84
• /
• 1967

A simple rotating micro mercury electrode is constructed in such a way that the mercury surface can be renewed quite easily with reasonable reproducibility. It consists of a glass capillary of about 1mm diameter connected to a mercury filled tube by means of a ground joint that allows mercury flow at a particular relative position only, and the electrical connection between the two parts is made by a platinum wire fused in the bottom of the latter. Thus the mercury surface exposed at the tip of the capillary replaces the platinum tip of the usual platinum micro electrode; however, the capillary has to be bent so that the tip directs upwards. It has been found to be a convenient electrode in the amperometric titration in strongly acidic media. Furthermore, it has been advantageously used in the alternating-current polarography because of its smaller electrical resistance than the ordinary dropping mercury electrodes. It also can be used as a stationary mercury electrode in fast scanning polarography.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.66-66
• /
• 2017

국내 농촌의 인구고령화, 여성화 증가로 인한 농촌노동력 감소 문제를 해결하기 위해 농업기계자동화에 관한 연구가 활발히 진행되고 있다. 본 연구는 자동화농업기계 중 자동 이식기의 성능평가 기술을 개발하기 위해 수행되었으며 이를 위해 자동 정식기의 핵심부품인 이식호퍼의 결주율, 이식율, 주간간격, 운동궤적 등을 측정할 수 있는 원형토조 실험장치를 개발하였다. 원형토조 실험장치는 원형토조, 이식호퍼 구동장치, 컨트롤러로 구성되어 있으며 이식호퍼의 회전속도(rpm)를 조절하여 주간간격을 조절할 수 있고 초고속 카메라를 이용하여 이식호퍼의 운동궤적을 측정할 수 있다. 이식작물로 고추, 양배추, 브로콜리의 3종류의 육묘를 이용하여 이식호퍼의 회전속도를 20~60 rpm 구간에서 10 rpm 단위로 속도조건변화를 주고 결주율과 이식율을 측정하였다. 이식호퍼 rpm 속도에 따른 주간거리는 190~560 mm로 나타났다. 각 rpm 단수, 작물별 평균 이식율은 고추육묘가 약 97%, 양배추육묘가 약 94%, 브로콜리육묘가 약 95%로 나타났다. 또한 초고속 카메라를 이용하여 측정한 이식호퍼의 운동궤적을 통해 선진사 제품과 대비하여 차이를 보인 것을 확인하였다. 향후 원형토조 실험장치를 이용해 다양한 작물 및 토양조건에서의 실험 및 토양저항 측정장치 개발을 통해 이식작업 진행중에 호퍼에 걸리는 부하에 대한 성능평가시험을 할 계획이다.

• Applied Chemistry for Engineering
• /
• v.2 no.4
• /
• pp.356-362
• /
• 1991

The physico-mechanical properties of NR/BR blend were measured, and the results were interpreted in terms of the crosslink density with cure system. The cure rate, maximum torque and crosslink density increase with the content and ratio of curative for cure system. Hardness, 300 % tensile modulus, rebound and wear resistance increase with crosslink density of the vulcanizate but heat build-up and tan $\delta$ at $60^{\circ}C$ decrease. It is expected that semi-EV(efficient vulcanization) cure system is appropriate for application in tire tread of truck/bus in which load bearing property is impotant.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.11
• /
• pp.1441-1446
• /
• 2012

An axial-piston-type hydraulic motor involves friction and leakage losses at the sliding parts, contact loss at the mechanism assembly parts, volumetric loss caused by the pressure drop, housing oil churning loss and compressibility from the hydraulic oil pipe resistance, etc. the friction and volumetric loss at the hydrostatic bearing between the piston shoe and the swash plate rotating at high speed and having an oil film gap of 8-15 ${\mu}m$ strongly affects the total efficiency of the hydraulic motor. In this study, a variable swash-plate-type hydraulic piston motor operating under a maximum pressure of 35 MPa, maximum speed of 2,500 rpm, and displacement of 320 cc/rev is tested to verify the optimal ratio of the hydrostatic bearing which is closely related to the hydraulic motor performance.