• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.5
• /
• pp.784-789
• /
• 2012

Ultrasonic Cutting which uses a tuned blade resonant in a longitudinal mode, has been used to cut a range of materials from confectionery, baked products and frozen foods, to wood, bone, foams and composites. The Blade design typically uses finite element analysis, and it could be predicted vibration mode, gain and amplitude uniformity of the blade tip at resonant frequency. In this paper, FEA used to predict the vibration characteristic of the blade, and then the results were verified by analysis system of resonant frequency using the processed blade. The crack of the blade which is predicted from FEA was compared with the crack occurred by cutting experiment of rubber materials using the processed blade.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.1
• /
• pp.70-75
• /
• 2012

The technique with ultrasonic vibration refers to the many industries. Especially Ultrasonic Connection Method is widely used for mobile battery, secondary battery, automobile components and also they recently started using it for terminal connecting of solar community battery. In this study, ultrasonic welding horn is analysed and designed with FEM, then manufactured based on it. Resonance frequency and amplitude of horn would be measured and compared with the designing result to judge the suitability. Al/Al specimen is welded by the manufactured horn and verify its performance via the weldability evaluation.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.9 no.3
• /
• pp.330-337
• /
• 1998

In this paper, we fabricated a pair of circulaly polarized conical horn antennas for evaluating the scattering characteristics of a hemispherical reflector and of propagation characteristics in in-building environments, which is required for constructing a new wireless in-building communication system of microwave band consisted of a hemispherical reflector installed on the ceiling. The measurements show the fairly good features such that cross-polarization discremination more than 27 dB and axial-ratio less than 1.25 dB.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.17 no.5
• /
• pp.84-90
• /
• 2018

When producing a plastic horn cover for an automobile, since the interval between the ribs on the inner surface is narrow, conventional cooling channels cannot be applied and cooling of the mold is difficult. For this reason, the molding operation cannot be completed within a set cycle time. In this study, a conformal cooling channel was applied on the mold to solve the cooling problem. Injection molding simulation was carried out to confirm the effectiveness of the conformal cooling channel. In the analysis results, the mold temperature at the rib section decreased by 33%, and the mold temperature also decreased by 31%. This reduction in temperature allowed for molding within a set cycle time and demonstrated the effectiveness of the conformal cooling channel.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.39 no.6
• /
• pp.27-27
• /
• 2002

In this paper, the LPA(Linear Power Amplifier) using new analog feedforward linearizer for IMT-2000 frequency band(2110MHz∼2170MHz) is proposed and fabricated. The designed analog feedforward linearizer system possessing the characteristics of stable operation for input power variation is simple structure and small size. When two-tones in IMT-2000 frequency band are applied to an amplifier, this LPA have the average output power is about 30W and the IMD value is below about 60dBc without correcting the circuit. In camparision with an amplifier without feedforward system at the same output power, the supposed analog feedforward linear amplifier posseses improved the IMD characteristics of over 23dB.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.39 no.6
• /
• pp.285-291
• /
• 2002

In this paper, the LPA(Linear Power Amplifier) using new analog feedforward linearizer for IMT-2000 frequency band(2110MHz∼2170MHz) is proposed and fabricated. The designed analog feedforward linearizer system possessing the characteristics of stable operation for input power variation is simple structure and small size. When two-tones in IMT-2000 frequency band are applied to an amplifier, this LPA have the average output power is about 30W and the IMD value is below about 60dBc without correcting the circuit. In camparision with an amplifier without feedforward system at the same output power, the supposed analog feedforward linear amplifier posseses improved the IMD characteristics of over 23dB.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.19 no.9
• /
• pp.1802-1811
• /
• 1994

In this paper, the corrugated horn antenna used in the reflector feed horn of satellite is analyzed using the modal expansion method. The modal expansion method is represented by the summations of modals at each point so the exact prediction of field and phase patterns can be obtained. The least number of iterations to compute field patterns is proposed. By using this number. calculation of accurate near and far field patterns without comsuming a lot of computational effort is available. Three kinds of corrugated horn antenna is designed to verify the method and experimented. The VSWR of designed frequency is from 1.04 to 1.1. The input impedance is nearly matched to $50\Omega$.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.12 no.2
• /
• pp.55-61
• /
• 2013

The horn is a key part of the ultrasonic welder. As the shape, mass and material of a horn have effects on the resonant frequency and the vibration mode in ultrasonic welding, a horn has to be designed and manufactured accurately. In this study, 40kHz band horn was designed and manufactured through the vibration mode and finite element analysis. A result of modal analysis showed that the natural frequency of the horn was 39,794Hz, and the frequency response by a harmonic response analysis was 39,800Hz - close to the intended frequency, 40kHz. In addition, weldability of the developed horn was estimated by welding of two Ni sheets and tensile-shear test of welded samples. It was shown the developed horn could be used in metal sheet welding.

• Proceedings of the Acoustical Society of Korea Conference
• /
• 1996.10a
• /
• pp.51-55
• /
• 1996

수중에서 가청 주파수 대역에서 평탄한 수중음향 방사체의 제작을 목적으로 두고 사전 조사로서 알루미늄 진동판과 혼스피커 유니트를 이용하여 수압에 대한 영향과 구동전기계의 절연 문제들을 고려하여 설계 및 제작하였다. 수조와 해양이 20m수심층에서 음향신호의 방사실험결과는 본 연구에서 설계.제작된 수중음향 방사체가 수압의 영향을 받으므로 이 영향을 고려하여 스피커의 후면에 설치한 공기주머니의 공기량에 따라 음향특성이 다르게 나타남을 확인할 수 있었다.

• Journal of Advanced Navigation Technology
• /
• v.11 no.1
• /
• pp.17-23
• /
• 2007

This paper, describes the VDR physical layer design in VDL Mode-2 in order to meet the requirements of International standards. VDR's frequency band is 117.975~137MHz, and CSMA(Carrier Sense Multiple Access), D8PSK(Differential Eight Phase Shift Keyed), 25KHz's channel bandwidth use. The analysis of the isolated channel from near channels, sensitivity of the receiver, dynamic range of the receiver, linear of the transmitter and energy of spurious for linear and non-linear simulation as a requirement condition of performance of VDR and teaches the course of design. The transmitting power level should be lower than 5dB from Po1dB point and the selected IF frequency is 45MHz to suppress the spurious signals. The receiver designed has 4.5dB of Noise figure, 27.52dB of Es/No, Mixer isolation up to 30dB, IIP3 power of LNA up to +10dBm to minimize the intermodulation.