• Applied Chemistry for Engineering
• /
• v.24 no.1
• /
• pp.31-37
• /
• 2013

Lowering surface reflectance of Si wafers by texturization is one of the most important processes for improving the efficiency of Si solar cells. This paper presents the results on the effect of texturing using acidic solution mixtures containing the catalytic agents to moderate etching rates on the surface morphology of mc-Si wafer as well as on the performance parameters of solar cell. It was found that the treatment of contaminated crystalline silicon wafer with $HNO_3-H_2O_2-H_2O$ solution before the texturing helps the removal of organic contaminants due to its oxidizing properties and thereby allows the formation of nucleation centers for texturing. This treatment combined with the use of a catalytic agent such as phosphoric acid improved the effects of the texturing effects. This reduced the reflectance of the surface, thereby increased the short circuit current and the conversion efficiency of the solar cell. Employing this technique, we were able to fabricate mc-Si solar cell of 16.4% conversion efficiency with anti-reflective (AR) coating of silicon nitride film using plasma-enhanced chemical vapor deposition (PECVD) and Si wafers can be texturized in a short time.

• Journal of Energy Engineering
• /
• v.10 no.3
• /
• pp.223-232
• /
• 2001

To study the stabilization characteristics of diffusion flame formed in the wake of a cylindrical bluff body with fuel injection, the flame stability limits, length and temperature of recirculation zone of flame, turbulence intensity distribution near the recirculation zone of flame were measured and analyzed. The length of recirculation zone is independent on main fuel injection quantity, but it is dependent on fuel injection angles, air stream velocity, and auxiliary fuel injection into recirculation zone. For diffusion flame, in general, the flame stabilization is deteriorated with increase of he length of recirculation zone, but if the turbulence generator is installed, the flame stabilization is improved with increase of the length of recirculation zone. The temperature of recirculation zone is dependent on fuel injection angles, auxiliary fuel injection into recirculation zone, turbulence generators, and it dependent on fuel injection angles, auxiliary fuel injection into recirculation zone, turbulence generators, and it has a maximum value at the condition of each theoretical mixture. In general, the more temperature of recirculation zone is low, the more flame is stable. But when the turbulence generator is installed, the more temperature of recirculation zone is low, the more flame is unstable. The turbulence intensity in the wake of bluff body is increased with increase of diameter or blockage ratio of grid. The more turbulence intensity is increased by installation of turbulence generator, the more flame is unstable. Finally, It is clear that the stabilization characteristics of diffuser flame can be controlled by some parameters such as fuel injection angles, auxiliary fuel injection into recirculation zone, turbulence generators.

• Journal of the Korean Electrochemical Society
• /
• v.16 no.4
• /
• pp.191-197
• /
• 2013

The one of the cathode material, $Li(Ni_{0.5}Co_{0.2}Mn_{0.3})O_2$, was synthesized by the precursor, $Ni_{0.5}Co_{0.2}Mn_{0.3}(OH)_2$, from the co-precipitation method and the morphologies of the primary particle of precursors were flake and needle-shape by controlling the precipitation parameters. Identical powder properties, such as particle size, tap density, chemical composition, were obtained by same process of lithiation and heat-treatment. The relation between electrochemical performances of $Li(Ni_{0.5}Co_{0.2}Mn_{0.3})O_2$ and the primary particle morphology of precursors was analyzed by SEM, XRD and EELS. In the $Li(Ni_{0.5}Co_{0.2}Mn_{0.3})O_2$ cathode from the needle-shape precursor, the primary particle size was smaller than that from flake-shape precursor and high Li concentration at grain edge comparing grain center. The cycle and rate performances of the cathode from needle-shape precursor shows superior to those from flake-shape precursor, which might be attributed to low charge-transfer resistance by impedance measurement.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.44 no.1
• /
• pp.1-7
• /
• 2018

In this study, 1,2-hexanediol, ethylhexylglycerin, and glyceryl caprylate known as skin conditioning agents with antimicrobial activity in cosmetics were investigated for their antimicrobial activity against gram-positive and gram-negative bacteria when combining them with various ingredients in cosmetic formulations. Seven kinds of substances expected to improve the antibacterial activity in formulations were selected to blend with these three compounds.; 1,3-propanediol, 1,3-butanediol, glycerin, dipropylene glycol, niacinamide, EDTA-2Na, and ethanol. The checkerboard assay was conducted to confirm the antibacterial synergy of these seven substances and the three skin conditioning agents. Consequently, ethanol and EDTA-2Na were detected as the significant materials with synergistic effect as well as ethanol showed antibacterial synergy with all the three compounds. When seven of selected materials were mixed with glyceryl caprylate, there were synergistic or additive activity against S. aureus, gram-positive bacteria and it was suggested that the combination with 1,2-hexanediol and glyceryl caprylate was useful to control both gram-positive and gram-negative bacteria when there were four kinds of polyols. This study is meaningful in that it confirmed the antibacterial synergy of the skin conditioning agents with antimicrobial activity and the main raw materials frequently used in cosmetics, thereby contributing to prediction of the antibacterial activity of the skin conditioning agents in cosmetic formulations.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.27 no.3
• /
• pp.122-129
• /
• 2017

For the production of a high-density ITO target, $In_2O_3$ powders with a small particle size and low agglomeration should be synthesized. The purpose of this study is to control the size and shape of the Indium hydroxide precursor which affects the properties of the $In_2O_3$ powder. As a starting raw material, Indium metal was dissolved in a Nitric acid ($HNO_3$) solution. The effect of concentration, pH, and temperature on the properties of Indium hydroxide was investigated using ammonium hydroxide as a precipitant. Crystallite size of each sample was analyzed by X-ray diffraction and the shape and the size of the powder was analyzed by transmission electron microscopy. As a result, the particle size of Indium hydroxide was increased with increase in the concentration of $In(NO_3)_3$ and the particle size and shape of the Indium hydroxide remained unchanged with increase in the pH of the solution. The particle size increased with increase in the precipitation temperature during precipitation.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.11
• /
• pp.226-233
• /
• 2013

In this study, In Laver's automatic drying device, laver thickness measurement and control devices that are associated with. Disconnect the water and steam, after put a certain amount of the mixture(water and laver) in the mold. In process, Laver of the size and thickness (weight) to determine, constant light source to detect and image LED Lamp occur Vision Sensor (Camera) prepare, then the values of these state of the image is transmitted in real time embedded computers. Built-in measurement and control with the purpose of the application of each of the channels separately provided measurements are displayed on a monitor, And servo signals sent to each of the channels and it become so set function should be. In this paper, the laver drying device, prior to the laver thickness measurement and control devices that rely on the experience of existing workers directly laver manually adjust the thickness of the lever, but the lever by each channel relative to the actuator by installing was to improve the quality. In addition, The effect of productivity gains and labor savings are.

• Journal of the Korean Electrochemical Society
• /
• v.7 no.4
• /
• pp.183-188
• /
• 2004

In order to develop polymer electrolyte for lithium/sulfur batteries, highly microporous P(VdF-HFP) membranes were prepared by phase inversion method. Porous structure was controlled by extracting NMP with mixture of deionized water and methanol. Porous structure of the membranes was observed with SEM. Polymer electrolytes were prepared by soaking the porous membranes in 1M $LiCF_3SO_3-TEGDME/EC$. The ionic conductivity of polymer electrolyte was found to be at high as $2\times10^{-3}S/cm$ when the polymer membrane extracted by $80\%$ methanol was used. The microporous polymer electrolyte optimized in this work displayed high ionic conductivity, uniform pore size, low interfacial resistance and stable ionic conductivity with storage time. The ionic conductivity of polymer electrolytes was measured with various lithium salts, and the conductivity showed $3.3\times10^{-3}S/cm$ at room temperature when $LiPF_6$ was used as a lithium salt.

• Resources Recycling
• /
• v.8 no.4
• /
• pp.45-56
• /
• 1999

The purpose of tlus sludy was to preparc raw material powder for Mn-Zn iclrile, h m mined mill scale and fero-Mn, usins a co-spray roasting process The mill scale and ferra-Mn uscd in this raalins process was rcf~nedb y mesn-ns of a slxc~apl rxcss ~nvolvinm~a te~ialsc ontalning imp~u-ltleso r less than 100 pprn In this study an effeclive spray roaster system. wllich produces fme complex oxide powder, collects produccd ~owder.,m d prcvel~tse ~~llssiooifi HCI gas. was also manufactured. By means of spray~ngp urifcd raw malerial solu~lionl nln a manufacued high tcmpervture rumace. &-ferrite powder and a comnpleu o ~ d e powder of Fe,O; and M,x203 were manufactured. The chmcterlstics of the composllion. surface urca, and p'miicle size dismbulion or the produced powder were exmined. ptoduced powdcr was then ~ m e dwi tli ZnO powder. aid olher addilives of defined cornposnion, and Mn-Zn femite cares werc praiuccil by meuns of Sorlning and closely controlled sintering processes. The magpelic p~oprlieso f c olo~ss, initlal permeability. mauin~u~mnn agnehc flux. coz~civcr orcc and residual magnccic flux for the above cores we,= measured, and fmm Il~ase I-csulls the eflicacy of lhe co-spray roasling pncess to pl.ellare raw material powder lor Mn-Zn ferntc was established

• Korean Chemical Engineering Research
• /
• v.46 no.1
• /
• pp.118-123
• /
• 2008

In the present study, the effect of oxyfluorination treatment on multi-walled nanotubes (MWNTs) supports was investigated by analyzing surface functional groups. The surface characteristics were determined by Fourier transformed-infrared (FT-IR) and X-ray photoelectron spectroscopy (XPS). After the deposition of platinum nanoparticles on the above treated carbon supports, a crystalline size and a loading level had been investigated. Electrochemical properties of the treated MWNTs-supported Pt (Pt/MWNTs) catalysts were analyzed by current-voltage curve measurements. From the results of surface analysis, an oxygen and fluorine-containing functional group had been introduced to the surface of carbon supports. The oxygen and fluorine contents were the highest value at the treatment of 100 temperature. The Pt/100-MWNTs showed the smallest particle crystalline size of 3.5 nm and the highest loading level of 9.4% at the treatment of 100 temperature. However, the sample treated at the higher temperature showed the larger crystalline size and the lower loading level. This indicated that the crystalline size and the loading level could be controlled by changing the temperature of oxyfluorination treatment. Accordingly, an electrochemical activity was enhanced by increasing the temperature of treatment upto 100, and then decreased in the case of 200 and 300. The highest specific current density of 120 mA/mg had been obtained in the case of Pt/100-MWNTs.

• Proceedings of the Korea Society for Simulation Conference
• /
• 1997.04a
• /
• pp.65-65
• /
• 1997

가입자가 B-ISDN(Broadband Integrated Services Digital Network) 서비스에 대한 shb은 수준의 품질 및 안정적인 서비스 제공을 요구함에 따라, 이러한 서비스를 제공하기 위한 ATM (Asynchronous Transfer Mode) 교환기에 대한 신뢰성 설계의 중요성은 증가하 고 있다. 교환기의 중요한 신뢰성 성능 척도 중의 하나인 연결 절단율 (Cutoff connection rate)은 총 연결시간 동안 절단된 연결수로 정의되며, 연결 절단은 호 설정 (Call setup) 단 계를 지나 서비스 중인 연결이 사용자의 요구가 아닌 시스템의 고장으로 종료될 때 발생한 다. 연결 절단율 추정 문제는 기존의 신뢰도 또는 가용도 예측을 위한 시뮬레이션과는 달리 시스템 구성 유니트들의 고장율, 수리율, 그리고 요구된 연결의 트래픽 특성 부분이 혼합된 문제이다. 따라서, B-ISDN 서비스의 중요한 특징인 다양한 트래픽 특성과 시스템의 구성 (Configuration)을 고려하여 연결 절단율을 해석적인 방법을 통하여 추정하는 데네는 어려 움이 있으며 시뮬레이션에 의한 방법이 적절하다. 본 고에서는 B-ISDN 서비스의 트래픽 특 성과 ATM 교환기의 시스템 구성 및 신뢰도 데이터로부터 시스템의 연결 절단율을 추정하 기 위한 시뮬레이터의 기능 및 구조, 시뮬레이션 수행 결과 등을 제시한다. 시뮬레이터는 AweSim 시뮬레이션과 CUser Written Code를 사용하여 개발하였다. 시뮬레이터의 구성 모듈은 크게 호 도착 모듈, 연결 제어 및 자원 할당 모듈, 유니트 고장 및 수리 모듈, 통계 량 수집 모듈 등으로 구성된다. 개발된 시뮬레이터는 B-ISDN 트래픽 파라메터와 연결 절단 율의 상호 관계 규명 및 시스템 설계 대안 (Design alternatives)에 대한 비교/평가에 활용 된다., 수중생물의 경우는 특히 수온, 수량 영양원등이다.(중략). 본 연구의 접근방법으로는 ASRS의 개념적인 Reference Model을 수립하고 이 Reference Model에 대한 Formal Model로 DEVS(Discrete Event System Specification)을 이용하여 시스템을 Modeling하였다. 이의 Computer Simulation을 위하여 DEVS형식론 환경에서의 Simulation Language인 DEVSim ++ⓒ를 이용하여 시스템을 구현하였다.. 실형 결과로는 먼저 선형 상미분방정식의 예로 mass-damper-spring system, 비선형 상미분방정식의 예로는 van der Pol 방정식, 연립 상미분방정식의 예로는 mixing tank problem 등을 보였으며, 그의 공학에서 일어나는 여러 가지 문제들도 다루었다.화물에 대한 방어력이 증가되어 나타난 결과로 여겨지며, 또한 혈청중의 ALT, ALP 및 LDH활성을 유의성있게 감소시키므로서 감잎 phenolic compounds가 에탄올에 의한 간세포 손상에 대한 해독 및 보호작용이 있는 것으로 사료된다.반적으로 홍삼 제조시 내공의 발생은 제조공정에서 나타나는 경우가 많으며, 내백의 경우는 홍삼으로 가공되면서 발생하는 경우가 있고, 인삼이 성장될 때 부분적인 영양상태의 불충분이나 기후 등에 따른 영향을 받을 수 있기 때문에 앞으로 이에 대한 많은 연구가 이루어져야할 것으로 판단된다.태에도 불구하고 [-wh]의미의 겹의문사는 병렬적 관계의 합성어가 아니라 내부구조를 지니지 않은 단순한 단어(minimal $X^{0}$ elements)로 가정한다. 즉, [+wh] 의미의 겹의문사는 동일한 구성요 소를 지닌 병렬적 합성어([$[W1]_{XO-}$ $[W1]_{XO}$ ]$_{XO}$