• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2002.02a
• /
• pp.401-406
• /
• 2002

식물조직 배양공정의 기계화 기술개발을 위한 기초자료를 얻고자 식물조직 배양기술의 개발 또는 식물묘를 대량생산하는 연구지도기관 및 농원 등의 배양실 10개소를 대상으로 배지의 분주, 배양용기의 밀봉 및 세척, 배양체의 접종공정 등에 대한 작업실태를 조사분석한 결과를 요약하면 다음과 같다. 가. 배양기술의 개발 또는 식물묘 대량생산은 대부분이 나리, 호접란, 풍란, 심비디움 등 화훼류였으며, 배지는 모두 한천이 혼합된 고체배지, 배양용기는 형상 및 용량 등이 다른 플라스크, 배양병, pE용기 등이 사용되었다. 나. 배지의 분주작업은 조사대상 10개배양실중 6개소는 작업자가 비이커를 사용하여 분주하였고 4개소는 자동 또는 반자동분주기를 사용하였으며, 인력 및 반자동분주기의 사용시 배양용기간의 분주량은 기준량의 $\pm$25%범위에서 차이가 있었다. 다. 액체배지의 분주시 온도는 36.8~88.$0^{\circ}C$, 점도는 3.7~11.8cP 범위였고 점도는 배지에 혼합하는 한천, 사과 등 유기물의 량에 따라 차이가 있으므로 배지의 분주작업을 기계화하기 위해서는 배지의 온도와 점도, 배양용기와 분주량 등을 종합적으로 고려하여 배지의 점도에 따라 분주량을 조절할 수 있도록 개발할 필요성이 있다고 생각된다. 라. 배양용기의 밀봉소재는 플라스크의 경우 호일 또는 고무마개와 호일, 배양병은 모두 나사산이 있는 캡, PE용기는 뚜껑을 사용하였으며, 밀봉작업은 모든 배양실에서 인력에 의존하였고 작업능률은 호일만으로 밀봉하는 경우 시간당 180~240병, 캡은 시간당470~600개 정도였다. 마. 배양체의 접종작업은 모든 배양실이 인력에 의존하였으며, 배양체를 배지와 분리하여 불필요한 부분을 제거하고 배양작물에 따라 생육정도를 2~3등급으로 구분하여 배양용기의 배지 위에 치상하는 과정으로 수행되었으며, 작업능률은 호접란의 경우 배양병에 25본을 접종하는데 시간당 6병, 심비디움은 원형 플라스크에 25본을 접종하는데 시간당 10병 정도였다. 바. 식물체의 대량증식에 사용되는 플라스크, 배양병, PE용기 등 배양용기의 세척작업은 농원의 1개배양실에서 간이식 세척기, 이 외의 9개배양실은 모두 물에 담겨 두었다가 세제와 브러쉬 등을 사용하여 인력으로 세척하고 있어 생력화 기술개발이 요구되었다.

• Resources Recycling
• /
• v.23 no.4
• /
• pp.30-36
• /
• 2014

300,000 tons of waste tires are annually being produced with development of the automotive industry in Korea. Landfill and incineration treatment system are causing the economic problem through secondary environmental pollution and waste. Therefore, as one of the ways to take advantage of this, Thermo-Plastic Vulcanized (TPV) composite was prepared by the ground waste tire and plastic powders. The waste tire powder was gained by mechanical fracturing through crushers. The waste tire powder was ground by a shear crushing method and a 2-stage disk mill method instead of cutting crushing one. The waste tire powder of 50 mesh was mixed with Polypropylene(PP) in various proportions. TPVs were prepared by an extrusion, and tensile and impact tests were performed. In addition, the same experiments were repeated in 40, 80, 140 mesh conditions in order to observe size effect of waste tire powders.

• Elastomers and Composites
• /
• v.45 no.4
• /
• pp.298-308
• /
• 2010

The mechanical properties and surface characteristics of parylene thin film were improved using Xylydene-based dimers (DPX-C, DPX-D, and DPX-N). A single-parylene-C, D, N film and a hybrid chemical and physical parylene thin films in which two types are mixed were manufactured for each dimer by adjusting the deposition conditions and the thickness of the thin film by input. Parylene was deposited by chemical vapor deposition (CVD) and the thermal characteristics of the single thin film and the hybrid thin film were compared by thermal analysis. The mechanical properties of the thin films were characterized by tensile strength, elongation, and tear force tests, and the surface characteristics of the thin films were evaluated by contact angle and surface energy measurements. The hybrid chemical parylene thin film in which two types are mixed can complement the strengths and weaknesses of the different dimers, while the physical parylene thin film can freely adjust the thin film characteristics of the coated surface and the opposite surface.

• Clean Technology
• /
• v.15 no.3
• /
• pp.172-179
• /
• 2009

The thermoplastic polyurethane waste (TPU-S) with good tensile properties, hardness, NBS abrasion resistance, specific gravity and low wet coefficient of kinetic friction was melt-blended with ethylene propylene diene monomer rubber (EPDM) with high wet slip resistance and low mechanical properties to form EPDM/TPU-S blend films, and their composition-property relationship was investigated to find the optimum composition for shoe outsole material. The properties except the wet slip resistance increased with increasing TPU-S contents in the blend. All the properties except elongation at break, specific gravity and the wet coefficient of kinetic friction in the range of $0{\sim}65\;wt%$ of TPU-S did not attain the values predicted by the simple additive rule. The optimum weight ratio of EPDM/TPU-S for the application to the typical shoe outsole material was found to be 30/70.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.21 no.12
• /
• pp.1132-1137
• /
• 2011

MRE(magneto-rheological elastomers) is a material which shows reversible and various modulus in magnetic field. Comparing to conventional rubber vibration isolator, MREs are able to absorb vibration of broader frequency range. These characteristic phenomena result from the orientation of magnetic particles named carbonyl iron powder(CIP) in rubber matrix. In this paper, simulation on variation rate of shear modulus for anisotropic MRE due to volume fraction of CIP and an effective permeability model was applied to predict the field-induced shear modulus of MREs. Also, the variation rate of shear modulus for anisotropic MRE was derived using magneto-mechanical theory. Based on Maxwell-Garnett mixing rule, the increment of shear modulus was calculated to evaluate the shear modulus of MREs with column structure of CIP due to induced current. The simulation results on variation rate of shear modulus can be applied to the variable mechanical system of MRE such as tunable vibration absorber, stiffness variable bush and mount.

• Fire Science and Engineering
• /
• v.31 no.3
• /
• pp.19-24
• /
• 2017

Flammable substances are used in laboratories and industrial process. The flash point (FP) is one of the most important physical properties used to determine the potential for characterizing the fire and explosion hazard of liquids. The FP data at 101.3 kPa were measured for the binary systems {toluene+ethylbenzene}, {methlycyclohenxane+ethylbenzene} and {n-heptane+ ethylbenzene}. The experiments were performed according to the standard test method (ASTM D 3278) using a SETA closed cup flash point tester. The measured FPs were compared with the values predicted using the following activity coefficient models: Wilson, Non-Random Two Liquid (NRTL), and UNIversal QUAsiChemical (UNIQUAC). The average absolute deviation between the predicted and measured lower FP was less than 1.74 K.

• Applied Chemistry for Engineering
• /
• v.10 no.7
• /
• pp.1041-1045
• /
• 1999

Three polysiloxaneimide(PSI) as membrane material were prepared by polycondensation of three aromatic dianhydrides(6FDA, BTDA, PMDA) with one siloxane-containing diamine(SIDA, aver. MW. 800). The PSIs were rubbery polymers containing 30~40 wt % of flexible siloxane chains and exhibited low density, high fractional free volume and low surface energy. They were used for pervaporation experiments with 0.05 wt % of four organic aqueous solutions containing ethyl acetate, methylene chloride, trichloroethylene, and toluene, respectively. With increasing hydrophobicity of organic solvents, both pervaporation selectivity and pemeation flux increase.

• Elastomers and Composites
• /
• v.22 no.4
• /
• pp.324-332
• /
• 1987

The thermal degradation of the homopolymer poly(methyl methacrylate) (PMMA) and flame-retardant tetrabrormobisphenol-A(TBBA) as well as of their blends were carried out using the thermogravimetric method in the stream of nitrogen gas with 60ml/min at various heating rate from 1 to $20^{\circ}C/min$. Friedman and Ozawa mathematical methods were used to obtain the value of activation energy.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.03a
• /
• pp.90-96
• /
• 2008

Engineered mixtures composed of rigid sand particles and soft rubber particles are tested to investigate their behavior with strain level. Mixtures are prepared with different volumetric sand fractions (sf) to identify response using small strain resonant column, intermediate strain oedometer, and large strain direct shear tests. The small strain shear modulus and damping ratio are determined with volumetric sand fractions. The asymmetric frequency response curve increases with decreasing sand fraction. Linear responses of shear strain and damping ratio with shear strain are observed at the mixture of sf=0.2. Vertical strain increases with decreasing sand fraction. Mixtures with $04.{\leq}sf{\leq}0.6$ show the transitional stress-deformation behavior from rubber-like to sand-like behavior. The friction angle increases with the sand fraction and no apparent peak strength is observed in mixture without sf=1.0.

• Explosives and Blasting
• /
• v.18 no.3
• /
• pp.89-97
• /
• 2000

최근 노후화 된 콘크리트 및 털 구조물에 대하여 환경 공해가 발생하지 않는 해체 기술의 필요성이 급증하고 있어서 이에 대한 연구가 활발히 이루어지고 있다. 그 결과 콘크리트 구조물을 일시에 해체하기 위하여 사용되고 있던 화약을 이용한 발파해체공법 및 군용 폭파 공법 등으로부터 응용되어 특수한 형태의 크기로 제작된 성형폭약을 철골구조물에 부착시킨 후 이를 폭발 시켜서 순간적으로 철골구조물의 철판(또는 빔이나 기타 부자재)을 절단 해체할 수 있게 되었다. 그 동안은 성형폭약의 폭발절단 효과에 영향을 주는 요소들인 대상 구조물의 재질 및 형상, 두께와 강도 특성, 성형폭약의 형상, 폭약의 종류, 장약량, Liner의 종류, Stand-off Distance, 성형폭약의 폭 및 너비, 기폭방법에 따른 영향과 폭발 절단시 발생되는 폭풍압에 의한 진동 및 소음의 영향 등에 대한 연구가 대부분이었다. 따라서 본 연구에서는 성형폭약의 주 구성요소인 화약과 금속성 Liner를 유연성이 탁월하고 조성 성분들의 혼합성과 성형성이 우수한 가소화제를 사용하여 제작된 성형폭약의 가소화 정도가 폭발절단력에 미치는 영향을 검토하였다. 이를 위하여 본 연구는 PETN 과 RDX 화약이 각각 25wt% 및 75wt%로 흔합된 화약원료를 85wt%로 하고 폴리이소부틸렌(P.I.B) 성분이 80 wt% 이상인 폴리부텐(P.B) 7wt% 와 부틸고무 4wt% 그리고 디에칠헥실세바케이트 4wt%로 구성된 가소화제를 사용하여 실험하였다.