• Journal of Korean Society of Steel Construction
• /
• v.13 no.5
• /
• pp.587-597
• /
• 2001

The structural system that discreterized continuous shells is frequently used to make dome-type structures and these structures show the unstable phenomena by snap-through or bifurcation when a load level reaches certain critical value. The characteristic structural behaviour of a cable dome shows a strong nonlinearity and very sensitive according to the initial imperfection. In this study the shape finding problem by applying initial tension stress is investigated and using this the unstable phenomena of perfectly shaped and initially imperfected shape model by external forces are examined to grasp the unstable behavior of cable dome using the Geiger-type model.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.583-586
• /
• 2017

Infrared signal measurement are conducted from a micro-turbo jet engine with different nozzle configurations. The conventional cone type, a S-shaped type with aspect ratio 5.2 and five rectangular type nozzle with different aspect ratios are used for this experiment work. The result show that infrared signal from the exhaust gas decrease as the aspect ratio increase. In case of S-shaped nozzle, the maximum infrared signal is reduced about 28.4% when compared of rectangular nozzle with aspect ratio 5(AR5).

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.10
• /
• pp.1269-1278
• /
• 2013

The cutting area changes periodically in the end-milling process because of its form generation mechanism. In this study, the effects of the cutting area on end-milled side walls are studied by developing a cutting area model that simulates the area formed by engagement between a workpiece and a cutting edge of the end mill. To do this, the straightness profile of the side wall in the axial direction is investigated. Models for estimating the cutting area and the transition point, where the slope of the straightness profile changes suddenly, are verified from real end-milling experiments under various radial and axial depth of cut conditions. Through this study, it is confirmed that the final end-milled side wall is generated in the regions where cutting areas are constant and decreasing in the down-cut. Similarly, in stable up-cut, it is also generated in the regions where cutting areas are increasing and constant. It is found that the transition point appears when the region changes.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.43 no.4
• /
• pp.413-420
• /
• 2023

Among the seismic structures for reducing earthquake damage, the seismic control structure is a technology that can efficiently improve seismic performance and secure economic feasibility by simply applying a damper. However, existing dampers have limitations in terms of durability due to required seismic performance and material plasticity. In this study, we proposed a polyurethane damper with enhanced recovery characteristics by applying precompression to polyurethane, which basically shows elastic characteristics, and applying superelastic shape memory alloy (SSMA). To verify the characteristics of the polyurethane damper, the concept was first established, and the design details were completed by selecting SSMA and steel, and selecting the precompression size as design variables. In addition, structural tests were conducted to derive response behavior and analyze force resistance performance, residual displacement, recovery rate, and energy dissipation capacity. As a result of the analysis, the polyurethane damper showed that various performances improved when the SSMA wire was applied and the precompression increased.

• Journal of the Korean Electrochemical Society
• /
• v.16 no.4
• /
• pp.191-197
• /
• 2013

The one of the cathode material, $Li(Ni_{0.5}Co_{0.2}Mn_{0.3})O_2$, was synthesized by the precursor, $Ni_{0.5}Co_{0.2}Mn_{0.3}(OH)_2$, from the co-precipitation method and the morphologies of the primary particle of precursors were flake and needle-shape by controlling the precipitation parameters. Identical powder properties, such as particle size, tap density, chemical composition, were obtained by same process of lithiation and heat-treatment. The relation between electrochemical performances of $Li(Ni_{0.5}Co_{0.2}Mn_{0.3})O_2$ and the primary particle morphology of precursors was analyzed by SEM, XRD and EELS. In the $Li(Ni_{0.5}Co_{0.2}Mn_{0.3})O_2$ cathode from the needle-shape precursor, the primary particle size was smaller than that from flake-shape precursor and high Li concentration at grain edge comparing grain center. The cycle and rate performances of the cathode from needle-shape precursor shows superior to those from flake-shape precursor, which might be attributed to low charge-transfer resistance by impedance measurement.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.4
• /
• pp.44-52
• /
• 2003

Shape memory alloys (SMA) are often used in smart structures as active components. Their ability to provide large recovery forces and displacements has been useful in many applications, including devices for artificial muscles, active structural acoustic control, and shape control. Based on the 3-dimensional SMA constitutive equation in this paper, the radial displacement control of externally pressurized circular and semicircular composite cylinders under external pressure with a thin SMA layer bonded on its inner surface or inserted between composite layers in investigated using 3-dimensional finite element analysis. Upon actuation through resistive heating, SMAs start to transform from martensitic into austenitic state, simultaneously recover the prestrain, and thus cause the composite cylinders to go back to their original shapes of the cylinder cross-sections.

• Journal of Aerospace System Engineering
• /
• v.16 no.4
• /
• pp.68-76
• /
• 2022

The purpose of this paper was to design the cable networks for mesh reflector antennas, considering the flexibility of structures. An effective form-find methodology is proposed. The whole parts of the cable networks are described by the absolute nodal coordinate formulation. Additionally, nonlinear deformation of the cable can be obtained. The form-finding analysis of the reflector with standard configuration is performed, to validate the proposed methodology. The truss ring structure is numerically modeled using the frame elements. To consider the flexibility of the truss ring as well as the cable net structure, an iteration analysis between the truss ring and the cable net under tensional forces is also performed in the form-finding process. The finial configuration of the reflector with tensioned cable networks is demonstrated.

• Proceedings of the Optical Society of Korea Conference
• /
• 2003.07a
• /
• pp.146-147
• /
• 2003

산업계에서의 다양한 제품 개발로 인해 새로운 형상 측정기술이 요구된다. 칩패키지와 실리콘 웨이퍼로 대표되는 광산란 표면 특성을 가진 제품들의 형상 측정은 거친 표면을 가진 반면 수마이크로의 형상 측정 정밀도를 요구하기 때문에 기존의 측정법으로는 기대하는 성과를 이루지 못해왔다. 현재까지 기존의 정통적인 측정법을 통해 측정 시도되어 온 방법들은 다음과 같이 두 방법으로 요약된다. 첫째, Kwon과 Han등은 경면(specular surface)을 측정하던 정통적인 간섭계에 10.6$\mu$m파장의 $CO_2$레이저를 광원으로 사용함으로써 가시광선 영역에서의 광산란 표면을 적외부 영역에서 경면화 하여 측정하였다. (중략)

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.60.2-60.2
• /
• 2010

본 연구는 상온 상압하에서 미세구조 패턴을 갖는 대용량의 CaCO3 박막을 제조하고 여러 가지 첨가제를 이용하여 박막 표면의 형상제어를 수행하였다. 또한 형상 제어된 CaCO3 박막을 템플릿으로 이용하여 고분자 및 금속 박막 형상 제어 연구를 수행하였다. 본 연구를 통해 개발된 LACS(Large Area CaCO3 Stamping)법을 통해 흡착능과 소수성의 특성과 같은 다양한 기능성을 갖는 박막의 제조가 가능하였다. 기존의 박막제조 기술은 주로 저압조건에서 이루어지기 때문에 대면적화가 어렵고 형상을 제어 하는데 여러 가지 단점이 있었던 반면 LACS는 에너지의 소모가 적고 다양한 형상제어를 통해 기존의 박막제조 기술의 단점을 보완할 수 있을 것으로 판단된다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.356-359
• /
• 2008

본 연구는 국내 고유의 가스화기 모델 개발의 목적으로 진행되었으며 다종의 가스화기 형상을 제안하고 전산해석을 이용한 비교검토를 통하여 국내 고유의 가스화기 개념설계에 활용하고자 하였다. 우선 downflow형 가스화기 3종과 upflow형 가스화기 3종에 대한 형상을 제시하고 cold flow 해석을 통한 가스화기내 유동특성과 체류시간등을 비교하였다. 또한 고유모델로의 개발에 적합한 형상을 고려하여upflow형 2종 및 downflow형 1종 등 총 3종을 선택하여 가스화 반응을 포함시킨 hot flow 해석을 진행하고 온도분포, CO 및 $H_2$의 가스농도분포를 비교하였다. 검토 결과 기존에 연구되어왔던 석탄가스기 형태인 upflow형 가스화기 하부에 산소공급노즐을 설치하는 경우 기존에 확보된 기술을 적용함을 물론 슬랙화효율을 높이는데도 잇점이 있을 것으로 판단되었다.