• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.3
• /
• pp.67-73
• /
• 2006

In this paper, a reconfigurable model following flight control method is proposed based on direct adaptive scheme using parameter estimation. Adaptive control scheme updates the control gains to make the system output follow the reference output even when fault occurs. By adopting the frequency domain parameter estimation method, system changes by the fault can be estimated. Recursive Fourier transformation is used for system identification. Using recursive Fourier transform, the proposed adaptive control algorithm guarantees the system stability and improves the system characteristics. To evaluate the performance of proposed control method, numerical simulations are performed.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.10
• /
• pp.846-852
• /
• 2012

The present paper is the preliminary study of the development of a morphing aircraft wing and investigates experimently the aerodynamic characteristics of a base airfoil and a morphing airfoil. The wind tunnel tests are conducted for a base Clark-Y airfoil, an airfoil with a mechanical flap, and a morphing airfoil. Lifts, drags, and pitching moments are measured by using a three-axis load cell and they are calibrated by considering solid blockage and wake blockage. The wind tunnel tests are conducted for various air speeds, Reynolds' numbers, and angles of attack. The experimental results show that the aerodynamic characteristics of the morphing airfoil in lift-drag and lift-pitching moment are better than those of the airfoil with a mechanical flap.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.46 no.10
• /
• pp.806-813
• /
• 2018

The fracture of a turbine blade of aerospace engine is presented. Although there are a lot of causes and failure modes in blades, the main failure modes are two ways that fracture and fatigue. Degradation of blade material affects most failure modes. Total propagation of failure in this study specifies failure of fracture type. Some section appears fatigue mode. Especially since this study describes analysis of failure for blade in high temperature, it can be a case in point. Analysed blade is Ni super alloy. Investigations of blade are visual inspection, material, microstructure, high temperature stress rupture creep test, analysis and fracture surface, etc. The root cause for fracture was stress rupture due to abnormal thermal environment. Thermal property of Ni super alloy is excellent but if each chemical composition of alloys are different due to change mechanical properties, selection of material is very important.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.4
• /
• pp.447-451
• /
• 2015

The objective of this study is to predict the structural characteristics of a heat exchanger mounted on an aircraft engine using finite element analysis. The plastic fracture and life of the heat exchanger were estimated by a thermo-mechanical analysis. Tensile tests were conducted under high temperature conditions (700, 800, 900, 1000 K) using five specimens to obtain the mechanical properties of the Inconel 625 tubes. To assess the structural characteristics of the heat exchanger, the full and partial models were applied under the operating conditions given by the thermo-mechanical and inertial load. As a result, the case, tubesheet, flange, and mounting components have a reasonable safety margin to the allowable stress assuming a fatigue strength of Inconel 625 of 10000 cycles under 1000 K.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.42 no.1
• /
• pp.47-58
• /
• 2014

In this research, the initial sizing of a HALE(High Altitude Long Endurance) UAV which uses solar power and hydrogen fuel cell as an alternative energy was performed. Instead of a wing box type, a glider type was chosen since it is relatively easy to get a data thanks to many researches abroad. Maximum takeoff weight is around 150Kg and the propulsion system is composed of motor, propeller, solar cell, and hydrogen fuel cell which can be recharged through electrolysis. Maximum takeoff weight was estimated as aspect ratio, wing span, wing area change while considering energy balance of required energy which is necessary for flight during the entire day and available energy which can be taken from the solar cell.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.8
• /
• pp.711-717
• /
• 2012

During the conceptual design phase of a light sport aircraft, the wind tunnel tests were conducted to investigate the static stability of newly-designed configuration. The 1/5 scale-down wind tunnel model consisted of fuselage, main wing, vertical tail and horizontal tail. The main wing and tails were able to be attached or detached from the fuselage. The aerodynamic forces and moments acting on the 6 different configurations compounding each component were measured by using the internal balance system and their static stability derivatives were derived. With these experimental data, the baseline lift and drag characteristics as well as the effects of each component to the longitudinal, directional and lateral static stability were quantitatively analyzed.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.39 no.6
• /
• pp.481-486
• /
• 2011

The evaluation of supercooled water droplet impingement characteristics of full-scale aircraft components in wind tunnels under icing conditions has been severely limited by the relative size of the component and the test facility. The concept of truncated airfoil sections has been suggested in order to extend the operational range of icing tunnels. With proper deflection of the small trailing-edge flap on the truncated airfoil the local pressure distribution may remain very close to that of the full-scale airfoil. In this study the shape of a truncated flapped airfoil is investigated for various deflection angles. To validate the truncated flapped airfoils, air flow and collection efficiency over the truncated airfoil are compared with the results of the full-scale airfoil obtained from the state-of-the-art icing simulation code.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.39 no.4
• /
• pp.306-313
• /
• 2011

The damage tolerance analysis is required to guarantee the structural safety and the reliability for aircraft components. The damage tolerance method, which evaluate the life considering the initial crack, considers a fatigue design model of the aircraft main structure. The fatigue crack growth life should be calculated in damage tolerance analysis and the inspection time to define the replacement cycle. In this paper, the damage tolerance analysis is performed for a turbine wheel which has complex geometry. The equation of the stress intensity factor for complex geometry is hard to know, so that they are usually processed by finite element analysis which takes long time. To solve this problem, the stress intensity factors at specified crack are obtained by the FEA and the crack growth life is evaluated using the surrogate model which is generated by the regression analysis of the FEA data. From the results, the efficiency of the crack growth life calculation and the damage tolerance analysis could be increased by taking the surrogate model.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.6
• /
• pp.467-474
• /
• 2012

UAVs for reconnaissance and intelligence operations require long endurance capability, which demands high efficiency of the propulsion system. The distributed propulsion system(DPS) generates the thrust by replacing a large propulsion system with a number of small propulsion systems. A DPS distributed along the wing span can produce gains in propulsion efficiency by reducing ejection velocity. Also, the ingestion of boundary layers through the distributed DPS inlet and ejecting flow from the outlet can improve the lift to drag ratio of the vehicle. This study investigates the effects of locations and size of the inlet and outlet of the DPS on the blended-wing-body design based on Eppler 337 airfoil, with a CFD tool. The fans in the DPS are modeled as actuator disks for computational efficiency. The best location and aspect ratio of the inlet and outlet are found from lift-to-drag ratio and pitching moment considerations.

• Journal of Aerospace System Engineering
• /
• v.16 no.6
• /
• pp.114-122
• /
• 2022

This paper explores three-dimensional unsteady computational fluid dynamic (CFD) analyses with an overset grid technique to analyse the wake effect created by a rotating propeller on a hand-launched unmanned aerial vehicle (UAV). Additionally, the influence of actual aileron deflection on the equilibrium condition of the rolling moment is examined in various hand-launched take-off conditions. The results of this study demonstrate the importance of initial aileron deflection in increasing the initial rolling stability during the hand-launched take-off process. Furthermore, an aerodynamic database is constructed to rapidly predict the aileron set values required for different take-off speeds and angle-of-attacks.