• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.253-253
• /
• 2016

최근 세계적으로 대체 에너지는 중요한 이슈가 되고 있으며 그 중 열전 재료는 유망한 에너지 기술로서 주목 받고 있다. 특히 고 직접화 전자 소자의 발열 문제를 해결하기 위해, 소형화와 정밀 온도 제어가 가능한 박막형 열전 소자에 연구가 주목 받고 있다. 박막형 열전소자 중 산화물 반도체계에 대한 연구가 활발히 진행되고 있으며, 이러한 산화물 반도체계 중 In2O3는 BiTe, PbTe 등의 기존의 재료에 비해 독성이 낮을 뿐만 아니라 내 산화성 및 고온에서 열적 안정성이 우수하여 고온에서 적용 불가능한 금속계 열전 재료의 한계를 극복 할 수 있다는 장점을 가진다. 우수한 성능 가장 낮은 캐리어 밀도를 가지기 때문에 의 열전 재료는 높은 전기 전도도 및 제백 계수 그리고 낮은 열전도도 특성을 가져야만 한다. IZO:Sn(Zn 10 wt.%, Sn 800 ppm) 박막의 경우, 높은 전기 전도성을 가지면서 비정질 구조를 가진다. 이와 같이 비정질 구조를 가지는 박막 열전 재료는 격자에 의한 열 전도도가 낮기 때문에 결정질 구조에 비해 전체 열 전도도 값이 낮을 것으로 기대된다. 따라서 높은 전기 전도도를 가지면서 동시에 낮은 열 전도도를 가지게 되어 우수한 열전 특성을 가질 것이라 예상된다. 이러한 특성을 바탕으로 본 연구에서는 비정질 구조를 갖는 Zn와 미량의 Sn을 동시에 첨가한 In2O3박막의 전기적 특성및 열전 특성을 관찰하고자 한다. 본 연구에서는 magnetron sputtering법으로 IZO:Sn(Zn 10 wt.%, Sn 800 ppm) 타깃을 이용하여 기판 가열없이 DC Power 70 W, 작업 압력 0.7 Pa으로 SiO2 기판 위에 $400{\pm}20nm$ 두께의 박막을 증착하였다. 이러한 공정으로 만들어진 박막은 대기 중 후 열처리를 각각의 200, 300, 400, 500, $600^{\circ}C$ 온도에서 진행하였다. 박막의 미세 구조는 XRD를 통해 관찰하였다. 그리고 박막의 전기적 특성은 Hall effect measurement을 통해 측정하였고, 열전 특성은 Seebeck 상수의 측정을 통하여 평가하였다. XRD 확인 결과 RT에서 증착한 박막과 후 열처리 200, 300, 400, $500^{\circ}C$ 결과 비정질 구조를 보였고, 후열처리 $600^{\circ}C$에서는 결정의 회절 피크를 보였다. 전기적 특성의 경우, 후 열처리 온도가 증가함에 따라 전기 전도도는 감소한다. 이는 공기중의 산소가 박막에 침투하여 oxygen vacancy를 막아 캐리어 밀도가 감소한것에 기인 된 것으로 판단된다. 열전 특성의 경우 제백상수는 후 열처리 $600^{\circ}C$에서 가장 높은 제백상수를 나타낸다. 제백 상수는 수식에 따라 캐리어 밀도의 -2/3승에 비례하게 된다. 수식에 따라 후 열처리 $600^{\circ}C$에서 가장 낮은 캐리어 밀도를 가지기 때문에 가장 높은 제백 상수를 가지게 된다. 열전 성능 척도인 Power factor는 제백 상수의 제곱과 전기전도도의 곱으로 나타내는데, 후 열처리 $200^{\circ}C$에서 가장 높은 Power factor를 보인다. 이는 캐리어 밀도 감소에 따라 전기 전도도는 감소하였지만 이로 인해 제백상수는 증가하였고, 또한 캐리어 밀도 감소에 따라 이온화 불순물 산란의 감소에 의해 이동도의 증가에 의한 것으로 판단된다. 박막의 경우 기판의 영향으로 인해 열 전도도 측정이 어려워 열전 성능 지수(ZT)를 계산을 할 수 없지만, 마그네트론 스퍼터링법으로 증착한 IZO:Sn 박막은 비정질 구조를 가지므로 격자진동에 의한 열 전도도가 낮아 전체 열 전도도가 결정질에 비해 낮을 것이며 이는 높은 열전 성능 지수를 가질 것으로 예상된다.

• Korean Journal of Soil Science and Fertilizer
• /
• v.45 no.2
• /
• pp.293-300
• /
• 2012

This study was to investigate the unsuitable rate of the storage facilities, the changes in corrosion process over time after installation according to the status, the time to install the facilities, years elapsed after facilities installation, inspection of methods and motivation, and so on, based on the results of the inspection at the petroleum storage facilities conducted by domestic soil-relate specialized agency to derive optimal management plans which meet the status of soil contamination facilities. The results showed that the facilities more than 5 years after the initial leak test at the time of the installation need to be inspected periodically by considering costs of leak test and remediation of polluted soil. The inspection period can be decided by cost and leak test methods showing discrepancies for the results obtained from individual test whether it was direct or indirect. To compensate these matters, we suggested that the direct inspection method on regular schedule is recommended. On the other hand, the inspection can be voluntarily completed to ease burden of the results by inspection or equivalent level to this inspection method. Also, it may need improved construction supervision and performance test system to minimize the occurrence of the nature defects in installing the facilities as well as the upgrade program for the facilities during intervals of inspection period.

• Clinical and Experimental Pediatrics
• /
• v.46 no.3
• /
• pp.217-223
• /
• 2003

Purpose : Every year, there is a remarkable increase in the prevalence of children with excess body fat. The aim of this study is to find a useful screening method in assessing adolescent, obesity and to specify the predictable risk factors that are related to adult cardiovascular disease according to BMI and obesity index. Methods : From July to November in 2001, a total of 2,814(male : female=2,011 : 803) mid to high school students who were in the obesity range according to obesity index(>20%) were evaluated according to height, weight, body mass index(BMI), obesity index, and serum lipid levels. Results : Among the obese students over 20% by obesity index, 86.6% were over the range of 95 percentile by BMI. Among students defined as obese by BMI, 21.0% of males and 21.4% of females students had hypercholesterolemia; by obesity index, the ratio was 20.7% male and 19.0% female. The frequency of hypertriglyceremia in male students was 15.0% in group I(overweight group, 85P97p); in female students 11.8%, 20.7% and 28.2% respectively. Conclusion : In this study, using BMI alone to test the serum lipid level in adolescent obesity had a limit of 10.0-17.0% omission. Therefore using obesity index as a screening method to find the adult cardiovascular disease would rather reduce the omission rate. The risk factor of cardiovascular disease according to BMI was the increasing level of triglyceride in both male and female students. We think that using the obesity index has more rationale rather than BMI in assessing lipid profiles.

• Progress in Medical Physics
• /
• v.23 no.4
• /
• pp.261-268
• /
• 2012

Breast cancer is the second leading cause of women cancer death in Korea. The key for reducing disease mortality is early detection. Although digital mammography (DM) has been credited as one of the major reasons for the early detection to decrease in breast cancer mortality observed in the last 20 years, DM is far from perfect for several limitations. Digital breast tomosynthesis (DBT) is expected to overcome some inherent limitations of conventional mammography caused by overlapping of normal tissue and pathological tissue during the standard 2D projections for the improved lesion margin visibility and early breast cancer detection. In this study, we compared a DM system and DBT system acquired with different thickness of breast phantom. We acquired breast phantom data with same average glandular dose (AGD) from 1 mGy to 4 mGy under same experimental condition. The contrast, micro-calcification measurement accuracy and observer study were conducted with breast phantom images. As a result, the higher accuracy of lesion detection with DBT system compared to DM system was demonstrated in this study. Furthermore, the pain of patients caused by severe compression can be reduced with DBT system. In conclusion, the results indicated that DBT system play an important role in breast cancer detection.

• Proceedings of the Membrane Society of Korea Conference
• /
• 1998.10a
• /
• pp.96-98
• /
• 1998

1. 서론 : 팔라듐이나 이의 합금막들은 높은 선택적 투과특성으로 인해 수소 정제나 분리막 반응기와 같은 산업응용 분야에서 매우 높은 관심을 갖고 있다. 상업적으로 이용되고 있는 이러한 막들은 통상적인 metallugical process에 의해 제조괸 self-supported type으로 수소 투과 속도가 낮을 뿐만 아니라 팔라듐 등은 고가의 귀금속이므로 비경제적이다. 따라서 현재 대부분의 연구자들은 기계적 강도를 유지하기 의한 다공성 지지체 위에 얇은 금속 박막을 코팅함으로서 투과성을 높이는 동시에 경제적인 복합막 형태의 막을 만드는데 연구의 촛점을 맞추고 있다. 이러한 형태의 막을 제조하기 위한 금속 박막 제조법은 무전해 도금법(electroless deposition), 화학증착법(CVD), 스퍼터링(sputtering), 전해도금법(electrodeposition) 등이 시도되었다. 그러나 수소에 대한 우수한 선택적 투과 특성을 갖기 의해서는 대부분 5$\mu$m 이상의 두꺼운 막을 제조하였으며 이보다 얇은 막의 제조에 한계가 있기 때문에 이들 막에 대한 기체 투과 특성에 대한 연구결과는 많지 않다. 본 연구에서는 기존의 전기도금법을 응용한 소위 'vacuum electrodeposition' 이란 새로운 기술을 도입함으로써 우수한 선택적 투과성을 갖는 2$\mu$m 이하의 팔라듐 합금 박막 제조를 가능하게 하였다. 지지체 표면의 거칠음 정도, 평균 기공 크기 등의 지지체 성질의 조절에 의한 금속 박막의 핀홀을 최소화함으로써 질소와 같은 inert gas의 투과도는 거의 없게 유지하는 동시에 금속 박막 두께, 결정 구조(e.g. grain size), 합금 조성 등을 조절함으로써 수소의 투과도를 높이고자 하였다. 있다. 후자의 경우, 미량의 과산화수소수 (1~10,000 ppm)를 이용해 처리 해주는 방법의 경우 경제적으로 큰 장점이 있고, 처리가 단순하다는 장점이 있으나 과산화수소수 자체에 포함하고 있는 높은 impurit level, 그리고 처리후 장시간의 flushing time을 가져야 한다는 단점등이 존재 하고 있다.요구된다. 몰입이 가능하여 임계치가 저하된 것으로 여겨진다. 또한 광학적 이득의 존재는 이 구조에 의한 극단파장 반도체 레이저다이오드의 실현 가능성을 나타내는 것이다.548 mL에 비해 통계학적으로 의의 있게 적었다(p<0.05). 결론: 관상동맥우회로 조성수술에서 전방온혈심정지액을 사용할 때 희석되지 많은 고농도 포타슘은 fliud overload와 수혈을 피하고 delivery kit를 사용하지 않음으로써 효과적이고 만족할 만한 심근보호 효과를 보였다.를 보였다.4주까지에서는 비교적 폐포는 정상적 구조를 유지하면서 부분적으로 소폐동맥 중막의 비후와 간질에 호산구 침윤의 소견이 특징적으로 관찰되었다. 결론: 분리 폐 관류는 정맥주입 방법에 비해 고농도의 cisplatin 투여로 인한 다른 장기에서의 농도 증가 없이 폐 조직에 약 50배 정도의 고농도 cisplatin을 투여할 수 있었으며, 또한 분리 폐 관류 시 cisplatin에 의한 직접적 폐 독성은 발견되지 않았다이 낮았으나 통계학적 의의는 없었다[10.0%(4/40) : 8.2%(20/244), p>0.05]. 결론: 비디오흉강경술에서 재발을 낮추기 위해 수술시 폐야 전체를 관찰하여 존재하는 폐기포를 놓치지 않는 것이 중요하며, 폐기포를 확인하지 못한 경우와 이차성 자연기흉에 대해서는 흉막유착술에 더 세심한 주의가 필요하다는 것을 확인하였다. 비디오흉강경수술

• Journal of the Korean Electrochemical Society
• /
• v.3 no.1
• /
• pp.49-56
• /
• 2000

In the present we.k, temperature dependence of oxygen diffusivity in the polyvinyl chloride (PVC) film $D_f$ formed on gold electrode was investigated using steady-state rotating disk electrode (RDE) technique and modulated electrohydrodynamic (EHD) impedance technique. Both the diffusion rate defined as the ratio of oxygen diffusivity in the PVC film to the film thickness $D_f/\delta_f$ and the time constant $\delta_f^2/D_f$ for oxygen diffusion through the PVC film were obtained from plot of the limiting current versus disk rotation speed and from filing the EHD impedance spectra experimentally measured to those theoretically calculated on the basis of the diffusion equation for mass transport through the non-conductive and porous film, respectively. By combining measured $D_f/\delta_f$ with $\delta_f^2/D_f$, we determined $\delta_f\;and\;D_f$ at room temperature separately. As temperature increased, it appeared that the $D_f$ value measured for the PVC film-covered gold RDE was enhanced more rapidly than that $D_s$ value in the solution measured for the PVC film-free gold RDE. This means that the pores glowing with increasing temperature act as effective diffusion paths within the film. The present in-situ steady-state and modulated EHD measurements prove to be effective for determining $\delta_f\;and\;D_f$, separately and at the same time the porosity of the PVC film at temperatures below glass temperature $T_g$ of the film.

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.2
• /
• pp.331-340
• /
• 2000

The existing two-phase biological fluidized bed has some problems such as limit of oxygen transfer and blockade of fluidized distributor. In this study, three-phase swirl flow biological fluidized bed has designed to solve the problems and to investigate its running characteristics. TOC of influent synthetic wastewater was approximately $70mg/{\ell}$. HRT of reactor was 1.6 hours. Mean particle size of sand, as packing media, was 0.397mm and packing volume was varied from $200m{\ell}/{\ell}$ to $600m{\ell}/{\ell}$ by stages in the bed. The amount of biomass and effluent water quality was throughly investigated in the bed. Showing experiment results from the above conditions, it was possible to solve the problems of existing fluidized bed and to keep DO of $3mg/{\ell}$ or more. And it was also TOC removal rate of 91 to 94 %, MLVSS of 2,360 to $3,860mg/{\ell}$, MLVSS per g-media of 8.4 to 17.3 mg/g, F/M ratio of 0.59 to $1.04kg-TOC/kg-MLVSS{\cdot}day$, biofilm thickness of $35{\sim}71{\mu}m$ and sludge productivity of 1.03 to $2.35kg-SS/m^3{\cdot}day$. Optimal conditions in this experimental were as follows.; those were biofilm thickness of approximately $54{\mu}m$. MLVSS per g-media of 13 mg and media packing volume of 350 to $400m{\ell}/{\ell}$ when F/M ratio was low, treatment efficiency was high and sludge productivity was low. Showing the media with optics microscope in this optimal condition, attached microbes such as Epistylis sp. were observed. From SEM photographs, it showed that Coccus adhere to and grow on the media surface.

• Korean Journal of Animal Reproduction
• /
• v.27 no.1
• /
• pp.45-51
• /
• 2003

This study was conducted to investigate the effects of castration and ovariectomy on growth performance and plasma hormone concentration in pigs. A total of 48 pigs of 35 days of age were used. The results obtained in the present study are summarized as follows: 1. No significant difference was found in average daily gain between ovariectomy group (898.6g) and control gilt group (862.7g), and between castration group (926.0g) and control boar group (945.5g), respectively. Average daily gain of control boar group, however, was significantly higher than that of control gilt group (p<0.05). There was no significant difference in feed/gain between ovariectomy and control gilt group and between castration and control boar group, respectively. Backfat thickness was significantly (p<0.05) higher in ovariectomy or castration group than in control gilt or boar group, respectively. 2. Plasma concentration of IGF-I was significantly (p<0.05) increased during the period of 5 weeks of age (45.1 $\pm$0.72 ng/ml) to 15 weeks of age (356.3$\pm$3.05 ng/ml), and maintained constantly afterwards in control gilt group, as was in control boar group. That of ICF-I tended to be lower in ovariectomy or castration group than in control gilt or boar group, respectively. Regarding steroid hormones of estradiol-17$\beta$, progesterone, and testosterone, the concentration was extremely low at 5 weeks of age, however, increased from 11 weeks to 23 weeks of age in control gilt or boar group, while it was nearly under detection limit in ovariectomy or castration group. 3. Chemical compositions of pork loins were not affected by ovariectomy or castration, except that crude ash content was significantly (p<0.05) higher in castration group than in control boar group. These results indicated that ovariectomy or castration had no effects on growth performance and feed utilization. However, the concentration of sex steroid hormones was under detection limit in ovariectomy and castration group. Further studies, however, are needed to develope the techniques which minimize the stress related with castration or ovariectomy for the production of high quality pork.

• Journal of Animal Science and Technology
• /
• v.49 no.4
• /
• pp.459-470
• /
• 2007

Domestically, finishing pigs are marketed at 110 kg on an average. However, it is thought to be feasible to increase the market weight to 120kg or greater without decreasing the carcass quality, because most domestic pigs for pork production have descended from lean-type lineages. The present study was undertaken to investigate the growth efficiency and profitability of ‘high’-market wt pigs and the physicochemical characteristics and consumers' acceptability of the high-wt carcass. A total of 96 (Yorkshire × Landrace) × Duroc-crossbred gilts and barrows were fed a finisher diet ad laibtum in 16 pens beginning from 90-kg BW, after which the animals were slaughtered at 110kg (control) or ‘high’ market wt (135 and 125kg in gilts & barrows, respectively) and their carcasses were analyzed. Average daily gain and gain:feed did not differ between the two sex or market wt groups, whereas average daily feed intake was greater in the barrow and high market wt groups than in the gilt and 110-kg market wt groups, respectively(P<0.01). Backfat thickness of the high-market wt gilts and barrows corrected for 135 and 125-kg live wt, which were 23.7 and 22.5 mm, respectively, were greater (P<0.01) than their corresponding 110-kg counterparts(19.7 & 21.1 mm). Percentages of the trimmed primal cuts per total trimmed lean (w/w), except for that of loin, differed statistically (P<0.05) between two sex or market wt groups, but their numerical differences were rather small. Crude protein content of the loin was greater in the high vs. 110-kg market group (P<0.01), but crude fat and moisture contents and other physicochemical characteristics including the color of this primal cut were not different between the two sexes or market weights. Aroma, marbling and overall acceptability scores were greater in the high vs. 110-kg market wt group in sensory evaluation for fresh loin (P<0.01); however, overall acceptabilities for cooked loin, belly and ham were not different between the two market wt groups. Marginal profits of the 135- and 125-kg high-market wt gilt and barrow relative to their corresponding 110-kg ones were approximately -35,000 and 3,500 wons per head under the current carcass grading standard and price. However, if it had not been for the upper wt limits for the A- and B-grade carcasses, marginal profits of the high market wt gilt and barrow would have amounted to 22,000 and 11,000 wons per head, respectively. In summary, 120～125-kg market pigs are likely to meet the consumers' preference better than the 110-kg ones and also bring a profit equal to or slightly greater than that of the latter even under the current carcass grading standard. Moreover, if only the upper wt limits of the A- & B-grade carcasses were removed or increased to accommodate the high-wt carcass, the optimum market weights for the gilt and barrow would fall upon their target weights of the present study, i.e. 135 and 125 kg, respectively.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.25 no.6
• /
• pp.487-495
• /
• 2012

In order to prevent the high velocity bullet from penetration, aluminum alloy and RHA(Rolled Homogeneous Armour) steel, which have a high tensile and compressive strength, are usually used as the bullet-proof armor material. Although these materials have a good bullet proof performance, but not an area density which is a weight increasing factor of bullet-proof armor. Therefore, Mg(magnesium) alloy is a promising substitute for the traditional bullet-proof armor material due to the relatively low areal density. The spatial efficiency of Mg alloy, however, is inferior to the traditional material's, which is a volume(thickness) increasing factor of bullet-proof armor. In this study, we select the multi-layered hybrid armor which consist of Ceramic, with a high strength; Mg alloy, with a low areal density; Kevlar, with a high tensile strength-to-weight ratio; in order to make up for the poor spatial efficiency of Mg alloy. By predicting V50 of the multi-layered armor against 9mm FMJ(Full Metal Jarket). we show that the multi-layered armor have the capability in improving bullet-proof performance in the respect of the areal density, but also the spatial efficiency.