• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.3
• /
• pp.193-198
• /
• 2017

Alloy 617 is one of the primary candidate materials to be used in a very high temperature reactor (VHTR) system as an intermediate heat exchanger (IHX). To investigate the low cycle fatigue behavior of Alloy 617 weldments at a high temperature of $850^{\circ}C$, fully reversed strain-controlled fatigue tests were conducted with the total strain values ranging from 0.6~1.5％. The weldment specimens were machined using the weld pads fabricated with a single V-grove configuration by gas tungsten arc welding (GTAW) process. The fatigue life is reduced as the total strain range increases. For all testing conditions, the cyclic stress response behavior of the Alloy 617 weldments exhibited the initial cyclic strain hardening phenomenon during the initial small number of cycles. Furthermore, the overall fatigue cracking and the propagation or cracks showed a transgranular failure mode.

• Journal of the Korea Concrete Institute
• /
• v.15 no.2
• /
• pp.163-172
• /
• 2003

As concrete structures are getting larger, higher, longer, and specialized, it is more required to develop steel fiber concrete and apply to the real world. In this research, it is aimed to have fatigue strength examined, varying the steel fiber content by 0%, 0.75%, 1.00%, 1.25%, by experimental study of Two-spans Beam with Steel Fibrous with repeated loads. The ultimate load and the initial load of flexural cracking were measured by static test. In addition, the load versus strain relation, load versus strain relation, load versus deflection relation, crack pattern and fracture mode by increasing weight was observed. On the other hand, the crack propagation and the modes of fracture according to cycle number and the relation of cycle loading to deflection relation and strain relation was observed by fatigue test. As the result of fatigue test, Two-spans Beam without Steel Fibrous was failed at 60~70% of the static ultimate strength and it could be concluded that fatigue strength to two million cycle was around 67.2% by S-N curve. On the other hand, that with Steel Fibrous was failed at 65~85% of the static ultimate strength and it could be concluded fatigue strength to two million cycle around 71.7%.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.5
• /
• pp.555-559
• /
• 2011

Oil hydraulic piston pumps are extensively used worldwide because of their simple design, light weight, and cost effectiveness. However, an oil hydraulic pump is likely to have high leakage, friction, and low energy efficiency after long-term use. In oil hydraulic piston pumps the clearance between the valve block and the piston plays an important role in the volumetric and overall efficiency. We studied the wear property of the SACM645 material used in hydraulic piston pumps via experiments with different heat treatments. We prepared three different specimens. The maximum tensile strengths of the QT and QT-nitration specimens are similar (about 820 MPa), but the strains are significantly different. However, the fatigue characteristic depended on the heat treatment.

• Journal of the Society of Naval Architects of Korea
• /
• v.34 no.2
• /
• pp.64-74
• /
• 1997

The necessity and importance of fatigue failure to variable load has been appreciated as the structural design technique develops and use of high tensile steel is increasing. This is much more appreciated for a large ship such as VLCC. The rigorous fatigue analysis and safety assessment should be, hence, carried out at the design stage to avoid the possibility of fatigue failure and to achieve the design result having a sufficient structural safety to fatigue strength. This paper deals with an efficient spectral fatigue analysis of ship structures by introducing the concept of stress influence coefficient. In the process included are probabilistic loading analysis, evaluation of long-term distribution of stress range and estimation of fatigue life applying the spectral fatigue analysis. An integrated computer program has been developed in which reliability analysis to fatigue strength is also included and has been applied to D/H VLCC.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.9 no.1
• /
• pp.127-135
• /
• 2005

Recently, as the concrete structures are becoming bigger, higher, longer and more special, high strength concrete is demanded. But the fracture behavior of high strength concrete is shown more brittle than that of the normal strength concrete. Therefore, in order to improve the brittle fracture behavior and crack propagation resistance, ACI Committee363 has been recommend the use of fiber reinforced concrete which showed superior property against the crack propagation resistance. On the other hand, bridges, concrete pavements and railroads etc. have been exposed to the repetition loading at least several million times during the service life. Therefore, fatigue load is dominantly most of all, but it is very difficult to estimate the suitable fatigue strength calculated by fatigue load. In this research, in order to examine the fatigue behavior of hybrid fiber reinforced high strength concrete, the static and fatigue tests were carried out. And from these results, it was estimated the fatigue strength of hybrid fiber reinforced high strength concrete.

• Journal of the Korean Institute of Gas
• /
• v.16 no.3
• /
• pp.29-34
• /
• 2012

Investigating safer ways to design and use to prevent a loss of life and property by failure of the structures are necessary and assessing total fatigue life with initiation and propagation of fatigue crack accurately through fatigue analysis is very important. The object of this study is to examine the initial life and propagation life when the fatigue crack is introduced from the root which is likely to appear in LOP(Lack of Penetration) cruciform fillet welded structure including bridges, ships and gas storage facilities which are impossible to be fully penetrated and to measure the rate of fatigue life until the final cleavage failure. As the result, each rate of fatigue life for fatigue failure is somewhat different in the range of 5% according to the thickness of material, however, the overall rate of initial life is in the range of 34~39% and propagation life showed the range of 61~66%.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1998.05b
• /
• pp.864-869
• /
• 1998

파단전 누수균열을 일으키는 가장 주요한 파손 형태는 피로파손으로 사료되어, 하나로 일차냉각계통 배관의 피로파손 가능성에 대한 정량적인 해석을 수행하였다. 하나로 일차냉각계통 배관은 발전로에 비해 저온, 저압이므로 ASME Class 3 로 분류되어 설계 완료되었지만 Class 3 절차에 의해서는 피로해석을 구체적으로 수행할 수 없어, 본 연구의 피로해석에 서는 Class 1 절차에 따라 피크응력강도의 범위를 보수적으로 계산하여 피로누적계수를 산정하였다. 일차냉각계통 배관 중에서 피로파괴 가능성이 가장 큰 것으로 예상되는 고응력 지점을 배관응력해석 결과로부터 선택하여 피로해석을 수행하였다. 선택된 분기관 연결부, 앵커 지점 및 butt 용접부의 피로누적계수들이 모두 1 보다 훨씬 작았으므로 열평창과 OBE 지진하중으로 인한 일차냉각계통 배관의 피로파손 가능성은 매우 희박한 것으로 나타났다. 따라서 냉각재 상실시 파단전 누수균열 개념을 적용하기 위한 일차냉각계통 배관의 피로파손에 대한 배관의 건전성은 충분히 입증된 것으로 판단된다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.39 no.10
• /
• pp.952-958
• /
• 2011

On-board IR calibration device has been developed for calibration of spaceborne image sensor. It is composed of a blackbody to provide two different radiance temperatures, tilt mirror with a function of stow and deploy to view the blackbody during the calibration and on-board calibration control unit to control the function of the blackbody and tilt mirror. In this paper, to guarantee the structural safety of the unit, the structural and thermal analysis including a thermo-elastic analysis for verifying structural safety on the soldered part of chips have been performed. In addition, safety margin of the chips on the PCB obtained from the conventional analytical method has been compared to the results from the FEM analysis.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.2 s.95
• /
• pp.225-233
• /
• 1999

This paper describes a versatile finite element technique which has been used to investigate of wide range of structural defects of practical importance. The procedure automatically remeshes the three-dimensional finite element model during the stages of crack growth. Problems analyzed to date include the surface cracks in leak-before-break situations, the development of quarter-elliptical corner defects, planar semi-elliptical surface defects and the fatigue growth of defects.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.6
• /
• pp.133-141
• /
• 2002

This paper describes a versatile finite element technique which has been used to investigate wide range of structural defects of practical importance. The procedure automatically remeshes the three-dimensional finite element model during the stages of crack growth. Problems include the surface cracks in leak-before-break situations, the shape development of multiple surface defects.