• Proceedings of the Korea Water Resources Association Conference
• /
• 2020.06a
• /
• pp.239-239
• /
• 2020

상수관망은 수용가에게 용수를 공급하는 사회기반시설물로, 용수를 공급하는 과정에서 관내에 이물질, 스케일 등의 생성은 불가피하다. 관로 변경, 단수로 인한 비상시 용수 공급 등의 유향 및 유속이 변화가 발생할 경우 스케일이 박리되어 적수사고 등의 수질문제가 발생 할 수 있으며, 이에 사전에 스케일을 제거 할 필요성이 있다. 스케일을 제거하기 위해서는 주기적인 관세척이 필요하며, 대표적인 공법으로는 플러싱공법이 있다. 현재까지 플러싱공법에 대한 연구는 실험을 통한 적용 권장 기준으로 진행되어 왔으나, 실제 상수관망에서 적용권장 기준을 확보하기 위한 방안에 대한 연구는 미흡한 실정이다. 플러싱공법의 대표적은 종류는 재래식 플러싱공법과 단방향 플러싱공법이 있다. 재래식 플러싱공법은 제수밸브를 조작하지 않는 방법으로, 모든 소화전에서 용수를 방출하는 공법이다. 단방향 플러싱공법은 제수밸브를 조작하여, 일정한 방향으로 요수를 방출하는 공법이다. 단방향 플러싱공법은 재래식 플러싱공법보다 유속확보 측면에서 유리하여 관로 세척을 위한 유량 및 유속 확보가 용이하다. 단방향 플러싱공법을 적용하기 위해서는 관로의 유속을 확보하기 위해 세척구역 정의하는 것이 필요하다. 이에 본 연구에서는 세척구역 정의를 통한 플러싱공법 적용 방안을 제안하고자 한다. 세척구역은 크게 3단계로 구분한다. 먼저 블록단위의 세척순서를 결정하고, 블록 내 관망 세척구역을 결정한다. 이때 관로의 관경, 곡선구간, 세척구역의 길이를 고려하여 세척구역을 정의한다. 마지막으로 결정된 세척구역을 제수밸브의 위치, 조작 횟수에 근거하여 세척순서를 결정한다. 본 연구를 통해 실제 상수관망 플러싱공법 적용 절차 수립에 기여할 수 있다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.2
• /
• pp.623-628
• /
• 2011

Micro EDM(Electric Discharge Machining) is one of the most powerful technologies which are capable of fabricating micro-structure without any problems from high cutting force. However, there is a significant defect in the part machining with deep holes or pockets, because debris which are generated by electric discharging may frequently cause a short circuit between an electrode and workpiece material. Vibration flushing can reduce the undesirable phenomena with dynamic flow of EDM fluid in a deep and choked area. In this study, Vibration flushing with solenoid is suggested and the results show that the method can generate a remarkable EDM efficiency with high amplitude at a low frequency in comparison with current vibration flushing methods with high frequency using piezo actuators.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.23 no.5
• /
• pp.541-548
• /
• 2017

A theoretical study on gas-liquid two-phase flow flushing systemnitrogen gas to the oil used for existing flushing equipment was conducted on the basis of ISO code so as to improve performance of existing high-temperature oil flushing equipment used in ocean plant facility drying field. For study, we analyzed process simulation results mixed fluid mixing ratio, temperature, Reynolds number and liquid hold up affectcleaning performance after designing oil-nitrogen gas mixture flushing system process. As a result, as the volume flow rate of mixed fluid increases with the tube diameter the volume fraction of the gas phase constant, the liquid fraction difference value at the inlet and outlet of horizontal hydraulic piping increases. It was found that the phase distribution between oil and nitrogen gas bubbles varies depending on the position the pipe lengthdirection. This change in phase distribution is expected to have a significant impact on the clean performance of an oil-nitrogen gas mixture flushing system.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2004.05b
• /
• pp.1361-1365
• /
• 2004

오염물질의 유입 유형은 일정한 농도를 가진 오염물질이 일정한 비율로 연속적으로 유입되는 경우와 순간적으로 특정한 농도를 가진 오염물질이 하천으로 유입되는 경우로 나눌 수 있다. 본 연구에서는 오염물질에 대해 댐 방류량을 일시적으로 증가시켜서 희석 및 세척시키는 플러싱(flushing) 효과에 관하여 연구하였다. 실측한 수리인자를 이용하여 적용성이 크다고 발표된 경험식에 의하여 확산계수를 결정하였다. 플러싱에 의한 오염물질의 희석정도 및 확산특성을 파악하기 위해서 RMA-4 모형을 잠실수중보$\~$신곡수중보 구간에 적용하였다. 정체되어있는 경우와 순간적으로 유입되는 경우, 성산대교 부근에서 농도가 1ppm이하로 감소하는 시간을 각 유량별로 분석하였다. 댐 방류량에 의한 플러싱을 시도한 경우에 본류의 오염물질이 지류로 역류하는 범위를 파악할 수 있었다.

• Journal of the Korean Society of Radiology
• /
• v.17 no.5
• /
• pp.701-707
• /
• 2023

In PET/CT, the injection volume of ¹⁸F-FDG directly affects the SUV(standard uptake value), which can affect the reading results. Therefore, it is important to inject the correct dose value of ¹⁸F-FDG. In this study, we performed the correlation between the residual radioactivity remaining in the syringe and catheter insertion device according to the number of flushing during ¹⁸F-FDG injection. CRC-25R dose calibrator, catheter insertion devices, 3 cc syringes and 50 cc physiological saline were used in this study, and the results were statistically analyzed. As a result, the total residual radioactivity of the syringe and catheter insertion device remained the highest at 5.84% after two flushing, and the least remained at 1.49% after five flushing. The correlation analysis results showed that the number of flushing had a negative correlation with the residual radioactivity of the syringe at -0.436 and the catheter insertion device at -0.300. As a result of one-way distributed analysis of the average according to the number of flushing, the syringe showed a significant decrease at 4 times, and the catheter insertion device showed a significant decrease at 5 times. However, considering that an average of 0.8% remains in the case of catheter insertion devices, four time flushing seems to be the most appropriate.

• Proceedings of the KIPE Conference
• /
• 2015.07a
• /
• pp.151-152
• /
• 2015

산업용으로 사용되는 전기흡착식 오일 플러싱 시스템에 코로나 방전층을 형성하기 위해서 10kV이상의 고전압원이 필요하다. 현재 전기흡착식 오일 플러싱 시스템을 위한 고전압원으로 고전압 변압기와 다이오드 정류 방식을 사용되고 있으나 변압기 구동을 저주파로 구동하므로 시스템의 크기 줄이는데 제약이 있다. 이러한 무게와 부피를 저감하기위한 다른 방식으로는 고주파의 하프 브릿지 컨버터와 2차단의 전압 더블러 방식을 채택하는데 이 방식의 경우 앞단의 스파이크성 전류로 인하여 다이오드의 발열 문제가 심각하다. 이러한 문제점을 해결하기 위해서 LC 공진형 컨버터를 제안하였으며 컨버터의 설계 또한 제시하였다. 이러한 설계와 제안된 컨버터의 효용성을 검증하기 위해서 최대 출력 150W와 출력전압 15kV의 시작품을 제작하여 실험을 실행하였다.

• Journal of Korean Society of Environmental Engineers
• /
• v.37 no.10
• /
• pp.563-572
• /
• 2015

The purpose of this study was to model the effect of flushing discharge on algae removal by multi-purpose weir operation in Yeongsan River (Seungchon Weir) using a 3-dimensional (3D) model. The chlorophyceae Eudorina sp. formed bloom in May 2013. Flushing discharge was conducted in two different ways for algal bloom reduction. To elucidate the spatial variability, a high-resolution 3D model, ELCOM-CAEDYM, was used to simulate the spatial variations of water quality and chl-a over a month. The results showed that ELCOM-CAEDYM could reproduce highly spatially resolved field data at low cost, and showed very good performance in simulating the pattern of algal bloom occurrence. The effect of each flushing discharge operation was analyzed with the results of modeling. The results of case 1, flushing discharge using an open movable weir, showed that the algal bloom between the Seochang Bridge and the Hwangryong River junction is rapidly flushed after operating the movable weir, but the residual algae remained in the weir pool as the discharge decreased. However, the results of case 2, fixed weir overflow with a small hydropower stop, showed that most of the algae was removed after flushing discharge and the effect of algae removal was much bigger than that in case 1, as per modeling results and observed data.

• Transactions of the KSME C: Technology and Education
• /
• v.4 no.2
• /
• pp.85-92
• /
• 2016

During ballast of a LNG carrier, the mud at the sea floor can enter the tanks together with the ballast water if the LNG terminal is located at shallow water region. In order to remove the mud deposited on the tank floor during deballasting, the mud flushing system in the ballast tanks is applied. In this study, various analyses to conform the efficiency in the mud removal are performed. In order to design the mud flushing system, the particle size of the mud is measured by particle size analyzer. Flushing performance is evaluated by numerical analysis. From the results of numerical analysis including flow field and piping system network, the optimized flushing system is determined.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.15 no.1
• /
• pp.23-31
• /
• 2006

The present works concerns a side flushing device for the improvement of the conventional Electric-Discharge Machining(EDM) process. In the EDM process, chips are usually generated as the workpiece is removed, and deposited between the electrode and the workpiece. This sediment degrades the surface finish of the machined product as well as the processing efficiency. In the present study, a flushing device with additional side injection equipments is proposed in order to remove the deposited chips effectively. Through numerical simulations, the validity of the proposed device is verified, and the influence of process parameters is investigated. Experiments have been also carried out in the die sinking EDM process. It was observed that the process efficiency and the surface finish are improved by virtue of the proposed flushing device.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.4 no.3 s.14
• /
• pp.43-50
• /
• 2004

This study had been performed to analyze flushing effects for instantaneous contaminants input with changing dam discharge in River. RMA-2 and RMA-4 models were applied to the downstream part of the Han River(from Jamsil submerged weir to Singok submerged one) The longitudinal dispersion coefficient of $50m^2/s$ was used. The four cases of dam discharges were selected as $500m^3/s,\;1000m^3/s,\;1500m^3/s$ and $2000m^3/s$, respectively, for 1 hour. The drought flow was fixed $200m^3/s$ in the Han River. The arrival time and the concentration of contaminant, the area of dispersion were estimated with RMA-4 model in the downstream part of the Han River. The arrival time which the concentration of contaminants become under 1ppm was analyzed with the stagnant and the instantaneous inflow contaminant at the section of Sungsan Bridge. The more increasing a dam discharge, the more short a dilution time of contaminant. The relation between the dam discharge and dilution time shows linearity. The instantaneous contaminant input was sensitively affected by the dam discharge than the stagnant contaminant one in the river. If it is tried to flush with a temporally increased dam discharge, it should be understood the range of overflowed contaminant dispersion from main channel to tributary channel.