• Proceeding of EDISON Challenge
• /
• 2016.11a
• /
• pp.23-26
• /
• 2016

Gurney Flap은 자동차의 스포일러 부분에 장착되는 고속주행용 Flap으로써 항공기에는 제한적으로 사용되고 있다. 매우 짧게 설치되는 특성이 있기 때문에 Flap의 길이를 항공기의 기준으로 10%로 증가시켜 Flap으로써의 역할을 확인해 보고자 실험을 진행하였다. Gurney Flap을 장착한 형상 3가지 모두 기본형의 NACA0012형상보다는 양력과 항력이 모두 증가하는 형상을 보였다. 양항비의 경우는 항력의 증가로 인해서 NACA0012에 비해서 모두 감소하는 것으로 나타났다. Gurney Flap은 고양력장치로 사용하기에는 다소 무리가 있지만, Dogfight와 같이 고항력장치를 사용하는 경우에는 좋은 성능을 기대할 수 있다.

• Journal of the Society of Naval Architects of Korea
• /
• v.58 no.1
• /
• pp.32-39
• /
• 2021

Korean coastal fishery suffers from profitability degradation due to a decrease in fisheries resources, pollution in coastal waters, fuel coast increase, and market opening for aquaculture products. The next generation Korean fishing vessel aims at the improvement of energy efficiency, enhancement of crew welfare, and safety. These purposes can be accomplished by adopting a new standard hull form with improved resistance performance and a modernized residence facility on the deck. In order to improve resistance performance, this study attempts to optimize design variables for stern flaps for three kinds of fishing vessels - coastal multi-purpose, coastal trap, and dredged nets. A series of model tests for these fishing vessels was carried out in the towing tank of Pusan National University. The results indicate that for some cases, the stern flap caused the stern trim of the vessel to decrease, leading to the resistance reduction.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.4
• /
• pp.261-267
• /
• 2013

In this paper, wind tunnel test and analytical prediction are compared for result of flapping motion in helicopter forward flight condition. Tests were performed at low speed wind tunnel at Chungnam National University, test section of wind tunnel has 1.8 by 1.8 meter open-jet test section area. According to the results of measured data for aerodynamic performance of model rotor in forward flight. It has to observed the difference of analytical and measured results of power coefficient for fixed thrust coefficient. And calculated and measured data of helicopter rotor flapping angles in forward flight are compared for a model rotor in a wind tunnel. A test was conducted to verify the measured data of coning and lateral/longitudinal flapping angle with predicted values.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.6
• /
• pp.509-516
• /
• 2007

Mathematical modeling and vibration control of a tiltrotor aircraft composite wing-rotor system are investigated in this study. A wing-mounted rotor can be tilted from the vertical position to a horizontal one, and vice versa. Effect of vibration control of the wing-rotor system via piezoelectricity is studied as a function of tilt angle, ply angle of composite wing and rotor's spin speed. Composite wing is modeled as a thin-walled box beam having a circumferentially uniform stiffness configuration that produces elastic coupling between flap-lag and between extension-twist behavior. Numerical simulations are provided and pertinent conclusions are outlined.

• Journal of the Korean Society for Railway
• /
• v.10 no.6
• /
• pp.786-791
• /
• 2007

Aerodynamically generated noise is dominant when the train speed approaches 300km/h. This noise sources is caused by the turbulent flow separations or vortex shedding from the train structure. Experiments were performed to investigate the characteristics of aerodynamic noise sources generated from exterior of the KTX trains and HSR-350x, especially from the inter-coach spacing. Measurements of both the inside and outside of the cabin are carried out to investigate the characteristics of the noise. Effect of the size of the mud-flap has been investigated through an wind tunnel test and it has been found that the low frequency noise is strongly dependent on the size of the gap. Also performed is an array measurement to locate different noise sources from the high-speed train. spectral characteristics of exterior noise sources are examined.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.310-315
• /
• 2003

This paper described that rotating test and fatigue test of a small-scale hingeless hub system with composite rectangular blades. Generally Rotating stability and fatigue test technique is one of Key-technology on test and evaluation for helicopter rotor system Rotating test of hingeless rotor system was achieved by means of rotor vibration characteristic and aeroelastic stability test GSRTS, equipped with hydraulic actuator and 6-component rotating balance was used to test hingeless rotor system especially for an observation of blade motion including flawing, lagging and feathering. Rotating test was done in hover and forward flight condition. Small-scaled blade fatigue test condition was determined by blade load analysis with the reference table of composite materials(S-N curve). Fatigue test bench was developed for the estimation of blade fatigue life, and tested its characteristic.

• Composites Research
• /
• v.17 no.3
• /
• pp.29-37
• /
• 2004

The aeroelastic stability analysis of composite bearingless rotors is investigated using a large deflection beam theory in hover. The bearingless rotor configuration consists of a single flexbeam with a wrap-around type torque tube and the pitch links located at the leading edge and trailing edge of the torque tube. The outboard main blade, flexbeam and torque tube are all assumed to be an elastic beam undergoing flap bending, lead-lag bending, elastic twist and axial deflections, which are discretized into beam finite elements. For the analysis of composite bearingless rotors, flexbeam is assumed to be a rectangular section made of laminate. Two-dimensional quasi-steady strip theory is used for aerodynamic computation. The finite element equations of motion for beams are obtained from Hamilton's principle. The p-k method is used to determine aeroelastic stability boundary. Numerical results are presented for selected bearingless rotor configurations based on the lay-up of laminae in the flexbeam and pitch links location. A systematic study is made to identify the importance of the stiffness coupling terms on aeroelastic stability for various fiber orientation and for different configuration.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.7
• /
• pp.29-36
• /
• 2004

In this work, the effect of composite couplings on hub loads of a hingeless rotor in forward flight is investigated. The hingeless composite rotor blade is idealized as a laminated thin-walled box-beam. The nonclassical effects such as transverse shear, torsional warping are considered in the structural formulation. The nonlinear differential equations of motion are obtained by applying Hamilton's principle. The blade response and hub loads are calculated using a finite element formulation in space and time. The aerodynamic forces acting on the blade are calculated by quasi-steady strip theory. The theory includes the effects of reversed flow and compressibility. The magnitude of elastic couplings obtained by MSC/NASTRAN is compared with the classical pitch-flap $({\delta}3)$ or $pitch-lag({\alpha}1)$ coupling. It is found that the elastic couplings have a substantial effect on the behavior of $N_b/rev$ hub loads. Nearly 10 to 40% of hub loads is reduced by appropriately tailoring the fiber orientation angles in the laminae of the composite blade.