• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.11
• /
• pp.828-833
• /
• 2018

It is well known that reflected waves and resonance affect phase distortion. In addition, phase delay can be distorted by antenna impedance. In this study, we analyze the phase delay variation caused by the antenna impedance, considering mutual coupling effects. In addition, we confirm the beam steering characteristics. When was -10 dB and -7 dB, the maximum phase delay error was $18.5^{\circ}$ and $26.5^{\circ}$, respectively. The Monte Carlo simulation with an eight-element linear array antenna demonstrated that the RMS error of the beam steering angle ranged from $0.19^{\circ}$ to $0.4^{\circ}$, and the standard deviation ranged from $0.14^{\circ}$ to $0.33^{\circ}$ when the beam steering angle was in the range of $0^{\circ}$ to $30^{\circ}$, with the uniformly distributed phase error of $18.5^{\circ}$ and $26.5^{\circ}$. The side lobe level increased from 0.74 dB to 1.21 dB by the phase error from the theoretical value of -12.8 dB, with a standard deviation of 0.31 dB to 0.51 dB. This is verified by designing an eight-element spiral array antenna.

• Journal of the Institute of Convergence Signal Processing
• /
• v.15 no.1
• /
• pp.9-14
• /
• 2014

The path loss data was re-calculated according to the distance between the base station and a mobile station in the mobile telecommunications network. In this paper, the averaged path loss data was plotted with the conventional path loss models(free space, plane earth, Hata model ${\ldots}$). The standard deviations for the 2 Km, 1 Km, 0.5 Km-interval averaged path loss were 2.29 dB, 3.39 dB, 4.75 dB, respectively. Additionally, the derivative values for the 2 Km, 1 Km, 0.5 Km-interval averaged path loss were evaluated to find the positions with more than 1 times or 2times of the standard deviation. The situations with the sharply fluctuated path loss were calculated to 5 positions in the 2 Km interval, to 7 positions in the 1 Km interval, to 19 positions in the 0.5 Km interval, respectively. And, the exact distances between the base station and a mobile station were found with the sharply fluctuated path loss.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.44 no.3 s.357
• /
• pp.78-84
• /
• 2007

A multistandard direct-conversion mixer for WCDMA, Wibro, and 802.11a/b/g is designed in 0.18 um CMOS technology To support multistandard and to reduce the chip area the switched inductor is used as the matching method. This switched inductor matching network selects the mixer's operation frequency band by turning on or off the switch transistor. Since the performances of mixer and operation frequency can be affected by the parasitic of switch transistor the mixer should be designed with the optimized size of switch to minimize parasitic effects. Proposed mixer is able to achieve return loss less than -13 dB in $2.1\sim2.5GHz$ and $5.1\sim5.9GHz$ bands with the suitable performance to meet requirements of WCDMA, WiBro, and 802.11a/b/g.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.44 no.1
• /
• pp.18-23
• /
• 2007

In this paper, LPDA standard antenna for measuring DTV signal strength is developed. Duralumin material is used to fabricate antenna having mechanical strength and flexibility. Operating frequency of designed antenna is range from $450{\sim}850$MHz and its gain is greater than 10 dBd to satisfy FCC requirements. Experimental results show that the developed antenna has minimum 10 dBd gain (average 11.7 dBd) over the entire frequency region and has ${\pm}1.5$ dB pass band ripple characteristic, From the results, the developed antenna is well adequate for standard antenna to measure DTV signal strength.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.11 s.102
• /
• pp.1106-1113
• /
• 2005

This paper presents a dual-band mixer for multi-standards of IEEE 802.1la/b/g using a single local oscillator, so as to improve the defects of legacy systems. Those systems have duplicate local oscillators and mixers to handle dual band signals, increasing complexity of system and power loss. The proposed circuit shows 11.6 dB, 16.8 dB of conversion loss and 8.77 dBm, 12.5 dBm of IIP3(Input 3rd Intercept Point) for respective bands when the two RF inputs of 2.452 and 5.260 GHz are down-converted to the identical 356 MHz If frequency. The RF-LO isolations are measured 36 dB, 41 dB at each frequencies and over 50 dB of LO-IF isolations are achieved at all cases.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.39 no.2
• /
• pp.92-100
• /
• 2002

The 16-port feed waveguide array with inductive walls analyzed by Galerkin's method of moments are proposed for the DBS reception system mounted on vehicle. First of all, in order to verify the validity of electromagnetic analysis and design for a $\pi$-junction feed waveguide, it is designed and fabricated at DBS band. The measurement results of a $\pi$-junction feed waveguide agree well with the theoretical ones. Based on this design method, an array design for WR-90 standard waveguide is conducted. Since the width of a $\pi$-junction feed WR-90 standard waveguide is larger than a guided wave length in an array design, the difference of amplitude and phase of 8-port array are calculated 2.3 dB and 62 degrees, respectively. The bandwidth with return loss of -20 dB below is about 220 MHz and it doesn't satisfy DBS band. To solve this problem, we propose a novel design that the width of a $\pi$-junction feed waveguide equals to a guided wave length. By the proposed novel design for 8-port feed waveguide array, the difference of amplitude and phase are decreased 1 dB and 13 degrees, respectively. The broad bandwidth of 700 MHz is also realized. The size of 16-port waveguide away compared with WR-90 array is reduced about 10 cm. The measured antenna gain for the fabricated 16-port feed waveguide array is observed 24 dBi above at DBS band.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.7
• /
• pp.685-691
• /
• 2003

This paper newly analyzes the effect of the phase noise in the frequency synthesizer on the performance of SFH/M-NCFSK system by standard frequency deviation(equation omitted) when noncoherent FSK demodulation of the square-law detector is considered. We derive the SER in the SFH system and analyze the effect of phase noise on the SFH/M-NCFSK system performance according to the hopping frequency spacing (1/T$\_$h/) and the variation of the standard frequency deviation (equation omitted). The required SNR is about 13.4 dB to meet Ps=10$\^$-3/ when the standard frequency deviation is about 4.0 Hz and the hopping frequency spacing (1/T$\_$h/) in the SFH/2-NCFSK system is 30. So, there is about 2.4 dB power penalty than the phase noise-free system. If the hopping frequency spacing 1/T$\_$h/ is under 30, the error floor may happen and SER considerably grows up. We show that the analytic results closely match with the simulation results.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.47 no.4
• /
• pp.18-24
• /
• 2010

This paper presents the improvement of the field uniformity in a reverberation chamber which can be substitute an anechoic chamber for the electromagnetic interference (EMI) and immunity test. Nowadays, there are many EMI issues due to the increasing use of wireless local area network (LAN), digital multimedia broadcasting (DMB), and mobile internet. With this reason, this paper studied the field characteristics in a reverberation chamber for 2.3 GHz band. In this paper, the finite difference time domain (FDTD) method is used to analyze the field characteristics in a reverberation chamber. To improve the field uniformity in the reverberation chamber, this paper adopted a 2D cubical residue diffuser (CRD) with varying the disposition and number of CRD. For each case, the tolerance and standard deviation of the electric field strength are evaluated. In comparison with the reverberation chamber without any CRD, the reverberation chamber with two CRDs showed improved results; 1.98 dB improvement in standard deviation and 3.6 dB improvement in tolerance.

• Journal of Digital Convergence
• /
• v.11 no.7
• /
• pp.201-207
• /
• 2013

The chirp signaling has been mainly used in radar systems due to its good correlation characteristics, and nowadays it is applied to real time locating system(RTLS). The RTLS with chirp signaling was chosen as a standard such as ISO/IEC 24730-5 and IEEE 802.15.4a. In this paper, the performance of a real time locating system with chirp signaling was evaluated and simulated with relative distance error rates. We considered three cases of S/I = -30[dB], -20[dB], and -10[dB] with Rician factor K=10 and K=20. The performance was enhanced with K factor improvement by 25%, 27% and 50% for respective three cases of S/I. As results, in case of S/I < -20[dB], the minimum signal power is required for performance improvement even though the line of sight component is helpful. And also, in case of S/I ${\geq}$ -20[dB], as the line of sight component is stronger the better performance is obtained.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2011.05a
• /
• pp.136-136
• /
• 2011

최근, 수자원의 효율적 이용을 위하여 농업용수로를 파이프라인으로 시공하는 지구가 증가하는 추세에 있다. 한편으로는 간척지를 복합농업단지, 시설원예, 신재생에너지단지 등 다각적으로 이용하는 정책을 추진하고 있다. 이에 따라, 농업용수 공급시스템도 개수로에서 관수로로 설계하는 추세에 있다. 농업분야에서 관수로를 활용하기 시작한 것은 ‘80년대 중반부터이나 그간 관수로 설계기준의 부재, 시범사업의 실패 등으로 인하여 보급이 지연되어 왔다. 일반적으로 관수로 설계는 노선선정, 관조직 구성, 관경산정, 관망해석, 도면작성 등 일련의 과정을 거쳐야 완성된다. 이 설계과정에서 관경산정 및 관망해석은 고도의 설계 노하우가 없으면 활용이 어려운 설계기술이다. 이번에 개발한 관수로 설계지원시스템은 관수로 설계 전문가가 처리해야할 일련의 설계작업을 AUTO CAD상에서 일관성 있게 처리할 수 있도록 개발한 것이 특징이다. 관수로설계지원시스템은 수치지도상에서 등고선 좌표, 표고 등을 자동 추출하여 사업계획서 및 종단도를 작성할 수 있으며, 관망심볼을 이용하여 시스템상에서 관망조직을 구성할 수 있으며, 다양한 안에 대한 노선검토, 관경산정, 관망해석과 관두께, 매설심도 등 구조해석이 가능하다. 그리고, 농업용 관수로의 제수밸브 등 부대시설에 대한 표준도를 D/B로 작성하여 설계도 작성시 참고할 수 있도록 개발하였다. 관수로설계지원시스템은 매뉴얼대로 처리하면 관망해석에 대한 전문지식이 없어도 설계에 활용이 가능하다.