• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2015.05a
• /
• pp.154-154
• /
• 2015

현재 액체로켓 엔진 연소기 내벽은 bonding layer NiCrAlY과 Top layer $ZrO_2$가 플라즈마 용사 방식으로 형성 된다. 이는 뛰어난 열 차폐 특성과 작업시간이 짧은 장점이 있지만, bonding layer와 Top layer 사이의 열팽창 계수 차이로 인한 균열 발생 가능성이 내재 되어 있고, 연소실 내벽에 균일한 두께의 코팅층을 형성하기 어렵고 설비가 비싸다는 단점으로 인하여 세라믹 코팅 층을 금속 코팅 층으로 대체 하고자 한다. 금속 코팅층은 모재와의 밀착성이 높고, 우수한 산화 및 부식방지 기능을 가지며 저렴하다는 장점이 있다. 또한 코팅 후 연마 작업이 가능해 연소실 내부형상을 설계조건 대로 유지 할 수 있는 특징이 있다. 따라서 본 연구에서는 연소실 내벽에 적용할 모재, 무전해 Ni-P 도금과 전해 Cr 도금층 사이의 밀착력 향상을 위한 방법에 대한 연구를 하였다. 밀착력 향상을 위한 요소로 전처리 용액과 열처리 시간에 따른 영향을 알아보고자 하였으며, 이를 위해서 5가지의 산세 용액으로 각 시편을 산세 한 후, 6시간, 12시간, 18시간 열처리 하여 단면을 비교하여 열처리에 영향을 알아보고자 하였다. 연구 결과 산세 용액의 영향은 크게 나타나지 않았으며, 열처리 시간이 길수록 Ni-P/Cr의 확산이 더 잘 일어나 확산층이 더 넓어지면서 밀착력이 더 좋아 진 것으로 판단되어 진다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.1A
• /
• pp.53-59
• /
• 2010

Recently, NDTs (Non-Destructive Techniques) using infrared camera are widely studied for detection of damage and void in RC (reinforced concrete) structures and they are also considered as an effective techniques for maintenance of infrastructures. The temperature on concrete surface depends on material and thermal properties such as specific heat, thermal conductivity, and thermal diffusion coefficient. Different porosity on cement mortar due to different mixture proportions can show different heat behavior in cooling stage. The porosity can affect physical and durability properties like strength and chloride diffusion coefficient as well. In this paper, active thermography which uses flash for heat induction is utilized and thermal characteristics on surface are evaluated. Samples of cement mortar with W/C (water to cement ratio) of 0.55 and 0.65 are prepared and physical properties like porosity, compressive strength, and chloride diffusion coefficient are evaluated. Then infrared thermography technique is carried out in a constant room condition (temperature $20{\sim}22^{\circ}C$ and relative humidity 55-60%). The mortar samples with higher porosity shows higher residual temperature at the cooling stage and also shows reduced critical time which shows constant temperature due to back wall effect. Furthermore, simple equation for critical time of back wall effect is suggested with porosity and experimental constants. These characteristics indicate the applicability of infrared thermography as an NDT for quality assessment of cement based composite like concrete. Physical properties and thermal behavior in cement mortar with different porosity are analyzed in discussed in this paper.

• Journal of the KSME
• /
• v.25 no.3
• /
• pp.236-241
• /
• 1985

본 고에서는 일반적으로 노즐 부위 열해석에서 무시되는 복사열전달율과 점성소산효과를 수치적 모델을 통하여 그 필요성 여부를 조사한 것이며 다음과 같은 결론을 얻었다. (1)연소실 및 수 렴부위에서는 복사열전달율이 대류열전달율과 같은 차수의 크기로 나타나고 있어서 고 복사율을 갖는 연소가스에서는 특히 중요하다. 특히 최근에 많이 사용되는 연료에는 연소가스에 산화알 루미늄 성분이 증가하는 추세이므로 노즐부위 열해석에는 복사열전달이 차지하는 비중이 커질 것이다. (2)노즐의 확산부위에서는 고속으로 인하여 가스자체의 점성소산이 일어나 특성치 보 정계수 값이 감소한다. 따라서 Bartz의 예측치 보다는 열전달계수의 값이 적어지고 있다. (3) 따라서 노즐수렴부위에서는 일반적으로 Bartz의 예상치보다 높고 확산부에서는 낮은 결과를 얻 었던 실험결과와를 비교할 때 고온고속 노즐에서의 열전달해석은 복사 열전달과 점성열 소산을 고려함으로써 정확하게 될 수 있다. (4)이상 고려된 실험 데이터와 수치모델의 고찰은 노즐내의 침식이 없는 경우이나 실제의 경우 노즐벽 표면에서 화학적 반응이 일어난다. 그러나 이때 발 생될 수 있는 순수한 발한효과는 미미하며 단지 전체적인 단면의 열 해석시 상기에서 예측된 열전달율을 근간으로 화학반응열 및 온도분포를 계산하여야 할 것이다.

• Journal of Energy Engineering
• /
• v.8 no.1
• /
• pp.181-188
• /
• 1999

재료의 표면을 pulsed laser로 가열할 때, 유한한 두께를 가지는 반무한 평판의 온도분포를 해석하여 열확산계수, 재료의 두께, 열원의 주기, 그리고 열원의 반경이 온도분포에 미치는 영향을 알아보았다. Pulsed laser에 의하여 가열되는 불투명 고체의 시간에 따른 온도는 전체적으로 증가하지만 열원의 주기와 동일한 주기를 가지고 일정한 온도차를 가지는 전체온도와 평균온도의 차, Tac가 존재한다. 열확산계수가 증가하면 재료 내부로 에너지의 확산이 활발하기 때문에 Tac는 커진다. 재료의 두께가 열확산길이보다 얇은 경우에는 두께변화에 따라서 온도가 민감하게 변하지만, 열확산길이보다 재료의 두께가 두꺼울 때는 두께의 변화에 관계없이 거의 일정한 온도가 나타난다. 열원의 단속주파수가 증가하면 한 주기당 에너지가 작아지므로 Tac의 크기는 작아진다. 열원의 반경이 커지면 단위면적당 에너지가 감소하므로 Tac의 크기는 삼각파, 싸인파, 사각파 순으로 크게 나타난다. 따라서 열원의 파형을 측정하여 이를 적용하는 것이 바람직하다.

• International Journal of Highway Engineering
• /
• v.12 no.3
• /
• pp.113-119
• /
• 2010

This study presents experimental findings on the performance of cement concrete pavement incorporating mineral admixtures such as ground granulated blastfurnace slag and silica fume. Flexural strength, compressive strength, charge passed, diffusion coefficient of chloride ions and initial surface absorption of cement concrete pavement incorporating mineral admixtures were periodically measured and the corresponding results were compared to those of plain concrete pavement. As a result, strength behaviors of concrete pavement were dependent on the types of mineral admixtures. However, it was true that incorporation of silica fume had a beneficial effect on compressive strength development. Furthermore, the application of mineral admixtures led to a lower diffusion coefficient of chloride ions compared to plain concrete pavement. Based on the experimental results, the present study would be helpful to design high-performance cement concrete pavement.

• Journal of the Korean Applied Science and Technology
• /
• v.29 no.1
• /
• pp.88-94
• /
• 2012

In this study, the current-voltage curves for metals were measured using cyclic voltammetry. The relationship between the electrochemical properties and surface states of metals were investigated by Scanning Electron Microscope (SEM). In cyclic voltammetry, we used a 3-electrode system for the electrochemical measurements. The measurement was conducted at the condition that consists of the first reduction from the initial potential to -1350 mV, continuous oxidation to 1650 mV, and last reduction to the initial potential. The scan rates were 50, 100, 150 and 250 mV/s. The results show the C-V characteristics of metals to be for an irreversible process, which was caused by the oxidation current from cyclic voltammogram, when monoethanolamine (MEA) was used as a corrosion inhibitor. When we used MEA as a corrosion inhibitor, the diffusion coefficient was decreased as the concentration of electrolyte was increased. In the SEM images of copper, we observed an increase of surface corrosion at the increased electrolyte concentration. Addition of $1.0{\times}10^{-3}M$ corrosion inhibitor MEA reduced the effect of corrosion prevention due to the relatively large diffusion coefficient at the electrolyte concentration of 0.1N.

• Journal of Radiation Protection and Research
• /
• v.11 no.2
• /
• pp.91-103
• /
• 1986

Experimental study for the leaching behavior of Cs-137 was carried out using the simulated evaporator bottom product of PWR plant. The method of leach test proposed by the IAEA was partially modified using ANS method. The effect of various factors, i.e., sampling method, curing temperature, curing time, leachant temperature, vermiculite addition and volume-to-surface ratio, was considered in this experiment. Diffusion model in semi-infinite slab was in a good agreement with the data obtained from 4-weeks cured specimens. The effective diffusion coefficient of the specimens which were cured at the temperature of $24^{\circ}C$ for 4 weeks was found to be $1.20{\sim}1.47{\times}10^{-11}cm^2/sec$. With the experimentally obtained diffusion coefficient ($1.47{\times}10^{-11}cm^2/sec$), long-term prediction for the leaching of Cs-137 was carried out using finite-slab approximation. The estimated fraction of Cs-137 which remains in the environment is found to be less than 0.25 percent of initial amount after 100 years. About 25 years after the beginning of leaching, its fractional amount in the environment reachs the maximum value, 0.66 percent of initial amount.

• Applied Chemistry for Engineering
• /
• v.8 no.4
• /
• pp.645-652
• /
• 1997

Electrochemical characteristics and kinetic parameters of copper ion reduction were investigated with a platinum rotating disk electrode (RDE) in a diffusion controlled region. Reduction of Cu(II) in sulfate had one-step two-xelectron process, while the reduction of Cu(II) in chloride solution was involved two one-electron processes. The transfer coefficient of Cu(II) in sulfate solution was lowest, and the transfer coefficient of Cu(I) in halide solutions had the value of nearly one. In chloride solutions, electrodeposition rate of Cu(II) was about one hundred times faster than Cu(I). Diffusion coefficient increased in the order of Cu(II) in chloride solution, Cu(I) in the iodide, bromide, chloride solution, Cu(II) in sulfate solution. The calculated ionic radii and activation energy for diffusion decreased in the same order as above. Morphological study on the copper electrodeposition indicated that the electrode surface became rougher as both concentration and reduction potential increases, and the roughness of the surface was analyzed with UV/VIS spectrophotometer.

• Journal of the Korean institute of surface engineering
• /
• v.36 no.1
• /
• pp.99-107
• /
• 2003

The diffusion coefficient of Xe-133 was obtained from an annealing test. The specimens were made from a UO$_2$ single crystal powder with natural enrichment. Weight and grain size were 300mg and ($23\mu\textrm{m}$, respectively. Oxygen potentials were obtained from an oxygen sensor. Released fractions were obtained from both results of gamma scans and quantitative analysis with MCNP code, The annealing test was performed at three temperatures at once. Diffusion coefficients of Xe-133 were calculated using slope of Booth theory in each O/M ratios. Activation energy and the pre-exponential factor of the diffusion coefficient were obtained. The activation energy of near stoichiomeric $UO_2$ is 310 kJ/mol. The measured values of near stoichiometric $UO_2$ are very close to other data available. Diffusion coefficients increase with hyper-stoichiometry, due to higher concentration of cation vacancies.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.20 no.7
• /
• pp.46-52
• /
• 2006

The effects of surface treatment on the hydrogen storage properties of a $Mg_2Ni$ alloy particle were investigated by the microvoltammetric technique, in which a carbon-filament microelectrode was manipulated to make electrical contact with the particle in a KOH aqueous solution. It was found that the hydrogen storage properties of $Mg_2Ni$ at room temperature were improved by the surface treatment with a nickel plating solution. The sodium salts(sodium phosphate and sodium dihydrogen citrate) contained in the nickel plating solution made the alloy form an amorphous-like state, resulting in an improved hydrogen charge/discharge capacity at room temperature as high as about 150[mAh/g] from the original value of 17[mAh/g]. Potential-step experiment was carried out to determine the apparent chemical diffusion coefficient of hydrogen atom($D_{app}$) in the alloy. Since the alloy particle we used here was a dense, conductive sphere, the spherical diffusion model was employed for data analysis. $D_{app}$ was found to vary the order between $10^{-8}{\sim}10^{-9}[cm^2/s]$ over the course of hydrogenation and dehydrogenation process.