• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.4
• /
• pp.457-463
• /
• 2012

Current refrigerators are designed to have thin doors and walls to facilitate user convenience and increase inner storage space. However, the thin doors and walls gives rise to the problem of dew generation on the outer surface of a refrigerator due to a large critical temperature difference between the outer wall and the room air; So far, an electric heater is commonly used for making the dew to evaporate; in this case, the heater inevitably requires additional electrical power. We propose a new approach to reduce the dew generation in a refrigerator by redesigning the gasket and varying the thickness of the inner case of the refrigerator. The results of simulations performed in this study indicate that the surface temperature in the region where dew was generated was increased by approximately $0.39{\sim}3.07^{\circ}C$ without the use of a heater.

• Fire Science and Engineering
• /
• v.24 no.4
• /
• pp.12-17
• /
• 2010

The purpose of this study is to determine how effectively waste tire recycled material mixed with flame retardant work in combating fire. As discovered in the previous study, waste tire mixed with cement mortar has more insulation capacity. However, this mortar is weak against fire. Therefore flame retardant, with a specific proportional mix, will be added to increase its fire prevention capacity. Tests will be made in accordance with ISO 5657 procedures for measuring fire ignition time, flame and shape variation of test pieces at the Building Material Test Institute. The test piece will be set up with horizontal levels having a constant radiation heat of $1{\sim}5W/cm^2$. Temperature transfers and increases from the surface into the interior. Combustible gases result due to pyrolysis, and regular contact is maintained between the fire source and the center of the test piece for assessment purposes. Ignition has not been occurred without adding retardant meaning that there is almost no possibility of ignition of waste tire particle. This fact can be considered as fire load to appreciate a volume of combustion materials. Flame is not occurred due to heat-absorbing effect by adding non-organic series retardant into waste tire particle. Conclusions have been summarized as follows; 1) Combustion of building material can be decreased by adding retardant to waste tire-mixing mortar. But compressive strength and insulation capacity of the material should be measured later. 2) Firing prevention and ignition are main points of building fire. Reasonable fire engineering assessment of interior material should be made for establishing effective disaster prevention system.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.39-39
• /
• 2007

원자층 증착(Atomic Layer Deposition: ALD) 방법은 반응물질들을 펄스형태로 챔버에 공급하여 기판표면에 반응물질의 표면 포화반응에 의한 화학적 흡착과 탈착을 이용한 박막증착기술이다. ALD법은 기존의 화학적 기상증착(Chemical Vapor Deposition: CVD)과 달리 자기 제한적 반응(self-limiting reaction) 에 의하여 반응가스가 기판 표면에서만 반응하고 가스와 가스 간에는 반응하지 않는다. 따라서 박막의 조성 정밀제어가 쉽고, 파티클 발생이 없으며, 대면적의 박막 증착시 균일성이 우수하고, 박막 두께의 정밀 조절이 용이한 장점이 있다. 이러한 ALD 방식으로 3차원의 반도체 장치 구조물에 산화막 등을 형성하는 공정에서 중요한 요소 중의 하나는 전구체의 충분한 공급이다. 따라서 증기압이 높은 전구체를 선호하는 경향이 있다. 그러나 증기압이 낮은 전구체를 사용할 경우, 공급량이 부족하여 단차 도포성(step coverage)이 떨어지는 문제가 있다. 원자층 증착 공정에서 전구체를 충분히 공급하기 위해전구체 온도를 증가시키거나 전구체의 공급시간을 늘리는 방법을 사용한다. 그러나 전구체 온도를 상승시키는 경우, 전구체의 변질이나 수명을 단축시키는 문제점을 발생시킬 수 있으며. 전구체를 충분히 공급하기 위하여 전구체의 공급시간을 늘이는 방법을 사용하면, 원하는 박막을 형성하기 위하여 소요되는 공정시간과 전구체 사용량이 증가된다. 본 논문에서는 이러한 문제점을 해결하기 위해 반응기 안에서 전구체 노출 시간을 조절하는 새로운 ALD 공정을 소개한다. 특히 이러한 기술을 적용하면 나노튜브를 성장시키는데 매우 유리하다. 본 연구에서 전구체 노출 시간을 조절하기 위하여 사용된 ALD 장비는 Lucida-D200-PL (NCD Technology사)이며 (TEMA)Zr와 H2O를 사용하여 ZrO2 나노튜브를 폴리카보네이트 위에 성장시켰다. 전구체의 노출 시간은 반응기의 Stop 밸브를 이용하여 조절하였으며, SEM, TEM 등을 이용하여 나노튜브의 균일성과 단차피복성 등의 특성을 관찰하였다. 그 결과 전구체 노출시간을 조절함으로써 높은 종횡비를 갖는 나노튜브를 성장 시킬 수 있음을 확인하였다. 또한 낮은 증기압을 가지는 전구체를 이용하여도 우수한 특성의 나노튜브를 균일하게 성장시킬 수 있었다.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.1
• /
• pp.99-104
• /
• 2014

In this paper, Fire resistance test was carried out in accordance with the change of the insulation conditions on the exposed side and unexposed side of the coaming to obtain optimal insulation conditions for class H-120 insulation in connection with specimen-1 of the preceding paper for the evaluation of fireproof performance for fire dampers according to hydrocarbon fire conditions. As a test result, specimen-2(88 mm, $171^{\circ}C$) was satisfied class H-120 insulation, but specimen-3(76 mm, $181^{\circ}C$) was exceeded thermal insulation acceptance criteria at 110 minutes, therefor, specimen-2(88 mm) is optimal insulation conditions as possible lightweight than specimen-1. Test result comparison, we concluded that temperature rising of the coaming insulation surface was influenced by conductive heat from the bulkhead, and coaming surface was influenced by radiant heat from blade & coaming.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.6
• /
• pp.585-592
• /
• 2011

The enhancement of the cold-start capability of polymer electrolyte fuel cells is of great importance in terms of the durability and reliability of fuel-cell vehicles. In this study, vanadium oxide films deposited onto the flat surface of metallic bipolar plates were synthesized to investigate the feasibility of their use as an efficient self-heating source to expedite the temperature rise during startup at subzero temperatures. Samples were prepared through the dip-coating technique using the hydrolytic sol-gel route, and the chemical compositions and microstructures of the films were characterized by X-ray diffraction, X-ray photoelectron spectroscopy, and field-emission scanning electron microscopy. In addition, the electrical resistance hysteresis loop of the films was measured over a temperature range from -20 to $80^{\circ}C$ using a four-terminal technique. Experimentally, it was found that the thermal energy (Joule heating) resulting from self-heating of the films was sufficient to provide the substantial amount of energy required for thawing at subzero temperatures.

• Journal of the Korean Wood Science and Technology
• /
• v.37 no.3
• /
• pp.208-215
• /
• 2009

As a fundamental study to develop absorbing materials on harmful volatile organic compounds (VOC) such as formaldehyde, structural and crystalline characteristics of MDF carbonized at different temperatures were examined by a scanning electron microscope and an X-ray diffraction method. Fibers in surface layer of MDFs showed more compressed morphology than those in middle layer of MDFs, but the porosity of MDFs increased with increasing the carbonized temperature. The wrinkle shape was frequently surfaces of cell walls was more severe than that at the lumina of cells. The shape of pits in the fibers of carbonized MDFs were hardly changed. The cell walls of MDFs carbonized at $400^{\circ}C$ and over showed an amorphous-like structure without cell layering. X-ray diffratograms from the MDFs carbonized at $400^{\circ}C$ showed a trace of crystalline cellulose. On the other hand, an amorphous diffraction pattern from carbons was obtained with the MDFs carbonized at $1,000^{\circ}C$.

• Composites Research
• /
• v.17 no.4
• /
• pp.18-24
• /
• 2004

In this paper, active shape control of composite structures actuated by shape memory alloy (SMA) wires is presented. The thermo-mechanical behaviors of SMA wires were experimentally measured. Hybrid composite structures were established by attaching SMA actuators on the surfaces of graphite/epoxy composite beams using bolt-joint connectors. SMA actuators were activated by phase transformation, which induced by temperature rising over austenite finish temperature. In this paper, electrical resistive heating was applied to the hybrid composite structures to activate the SMA actuators. For (aster and more accurate shape/deflection control of the hybrid composite structure, PID feedback controller was designed from numerical simulations and experimentally applied to the SMA actuators.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.28A no.10
• /
• pp.840-846
• /
• 1991

In case of the rapid thermal process by halogen lamps, an optical pyrometer is generally used to measure the temperature. It is, however, necessary to measure the temperature by the thermocouple when the process temperature is lower than 700$^{\circ}C$ and the correction of the temperature is required. Contact by the PdAg paste is commonly used out but in this case it is impossible to see the effect of surface states of the substrate, which is critical in the rapid thermal process. In this study, real temperature ramping speed of silicon substrates coveredwith various thin films such as SiO$_2$2, Si$_{3}N_{4}$, dopants, and conductive layers (Ti or Co) was investigated by a mechanical contact of the thermocouple. And the results were compared with the case in which the contact was made by the PdAg paste. Effect of process ambient was also studied. It was found that depending on the surface state, overshoot more than 100$^{\circ}C$ could occur. It was also found that in case of the substrate covered with conductive layers, mechanical contact might render the correct temperature.

• Journal of Korea Foundry Society
• /
• v.28 no.5
• /
• pp.199-203
• /
• 2008

현재 사용되고 있는 진동감쇠능 Mg-Zr 합금인 K1A는 우수한 진동감쇠능을 갖으나 열악한 기계적 특성과 Zr이 고가이면서 고융점 원소로 합금화가 어렵다는 문제점 때문에 진동테이블, 미사일 유도시스템 및 레코딩 장비 등에 소량만 적용되고 있다. Mg-Ni 합금의 경우Ni가 Mg 용탕 내에 고용되지 않아 우수한 진동감쇠능을 갖으나 Fe, Cu등과 함께 Mg의 부식을 가속시키는 원소로 사용이 제한적일 뿐 아니라 Zr과 마찬가지로 Ni도 고융점 원소로 합금화가 어렵다는 것도 문제점으로 작용하고 있다. Mg-Si 합금의 경우 Si이 극소량만 고용되어 우수한 진동감쇠능을 보이며 Ni과 달리 부식에 영향을 받지 않는 원소이지만 Zr, Ni와 마찬가지로 고가이면서 고융점 원소로 합금화가 어렵다는 문제점이 있다. Mg 용탕에 첨가하게 되면 용탕의 표면에 MgO, CaO 피막을 형성하여 발화현상을 억제할 뿐 아리라 첨가량의 증가에 따라 발화온도를 상승시키는 Ca의 경우 Mg 내에 고용되어 진동감쇠능을 감소시킬 뿐 아니라 유동성 저하 및 열간균열을 야기하는 것으로 나타났다. 그러나 CaO의 경우 Mg내에 고용되지 않고, 가격이 저렴하며 Mg 고유 특성의 변화가 적다. 또한 Ca와 같이 Mg 용탕의 발화를 억제하여 보호가스인 $SF_6$를 사용하지 않아도 된다. 이런 다양한 장점을 갖는 CaO를 첨가한 Mg합금이 진동감쇠능을 유지하면서 기계적 특성이 향상된다면 주행 시 안전성 및 정음성이 요구되는 수송기기 분야와 외부충격으로부터 데이터 보호가 필수적인 휴대용 전자정보통신기기 분야에서 적용이 증가할 전망이며 이에 따라 이 분야에 대한 지속적인 연구와 투자가 이루어져야 할 것이다.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.3 no.1
• /
• pp.1-11
• /
• 1993

A suppression of turbulent fluid motion and a control of oxygen and dopants could be improved by application of magnetic field in Czochralski growth of silicon. The effect of an axial magnetic field on Czochralski system was numerically calculated. The fluid motions induced by temperature gradients and by crystal and crucible rotations were suppressed by magnetic force. The S/L interface was gradually flattened in proportion to the increase of magnetic field due to a reduced ascending velocity in the vicinity of center line. The t.emperature distributions in the melt at 8=0.3 Tesla were similar to those analyzed by the conduction heat transfer only. The dissipated amounts of heat flux from melt and crystal surfaces by Ar gas blowing was Jess than 3 %.