• Journal of the Korean Recycled Construction Resources Institute
• /
• v.9 no.3
• /
• pp.330-337
• /
• 2021

3D printing is not only at the fundamental study and small-scale level, but has recently been producing buildings that can be inhabited by people. Buildings require a lot of cost and labor to work on the form work, but if 3D printing is applied to the building, the construction industry is received attention from technologies using 3D printing as it can reduce the construction period and cost. 3D printing technology for buildings can be divided into structural and non-structural materials, of which 3D printing is applied to non-structural materials. Because 3D printing needs to be additive manufacturing, control such as curing speed and workability is needed. Since cement mortar has a large shrinkage due to evaporation of water, cement polymer dispersion is used to improve the hardening speed, workability, and adhesion strength. The addition of polymer dispersion to cement mortar improves the tensile strength and brittleness between the cement hydrate and the polymer film. Cement mortar using polymer materials can be additive manufacturing but it has limited height that can be additive manufacturing due to its high density. When light-weight materials are mixed with polymer cement mortar, the density of polymer cement mortar is lowered and the height of additive manufacturing, so it is essential to use light-weight materials. However, the use of EVA redispersible polymer powder and light-weight materials, additional damage such as cracks in cement mortar can occur at high temperatures such as fires. This study produced a test specimen incorporating light-weight materials and EVA redispersible polymer powder to produce exterior building materials using 3D printing, and examined flame resistance performance through water absorption rate, length change rate, and cone calorimeter test and non-flammable test. From the test result, the test specimen using silica sand and light-weight aggregate showed good flame resistance performance, and if the EVA redispersible polymer powder is applied below 5%, it shows good flame resistance performance.

• Journal of the Korea Institute of Building Construction
• /
• v.19 no.6
• /
• pp.485-494
• /
• 2019

This study is to evaluate the effect of admixtures such as blast-furnace slag and fly ash on adhesion in flexure and tension of polymer cement mortar(PCM) using SAE emulsion. The test specimens are prepared with five polymer-cement ratios and five admixture contents, and tested for flexural strength, adhesion in flexure, tensile strength and adhesion in tension. Based on the test results, no improvement of flexural strength and adhesion in flexure caused by admixtures in PCM can be indicated, but the tensile strength and adhesion in tension is improved due to mixing of the admixtures. In particular, the maximum of adhesion in tension of PCM with P/C 20% and BF content of 10% is 3.35MPa which is about 2.36 times higher than that of ordinary cement mortar, and 1.32 times that of PCM that does not contain any admixture. The average ratio of adhesion in tension to tensile strength of PCM was 48.7%. It is apparent that admixture contents of 5% or 10% could be proposed for improvement of tensile strength and adhesion in tension of PCM.

• Proceedings of the Mineralogical Society of Korea Conference
• /
• 2001.06a
• /
• pp.7-7
• /
• 2001

다량의 점토 퇴적물로 구성된 연약지반은 대단히 큰 압축성과 낮은 강도, 높은 함수량등의 물리·역학적 특성을 갖는다. 이러한 기초지반으로서의 불리한 특성 때문에 이를 대상으로 하는 각종 토목건설공사에서는 지반개량이나 안정처리가 반드시 선행되어야 할 과제이다. 이를 위해 종래에는 샌드드레인, 페이퍼드레인 등의 물리적인 공법에 의한 지반개량이 주류를 이루었으나, 최근에는 생석회나 시멘트계 고화재를 이용한 화학적 안정 처리공법이 크게 주목을 받고 있어 이에 대한 연구가 활발한 상황이다. 본 연구는 연약 지반 안정처리에 대한 방안을 모색하기 위하여 김해 지역에 분포하는 점토 퇴적물을 대상으로 각종 광물재료를 이용한 반응실험을 통하여 반응생성물 조사와 압축강도시험 등을 행하여 그 결과를 검토하였다. 우선 연약지반의 고화에 이용 가능한 생석회, 석고, 플라이에쉬, 고분자폴리머, 시멘트 등을 사용하여 점토와 혼합한 고화실험을 행하였으며, 이에 대한 물성 및 반응생성물을 검토하였다. 이러한 각 재료를 점토에 혼합한 후 PVC관에 모울딩하여 양생시켜 실험하였다. 그 결과, 석고 및 소석회에 비하여 생석회의 경우가 비교적 큰 압축강도를 나타내고, 균열발생 빈도도 낮았다. 생석회의 경우에 Gehlenite, Hillebrandite 등의 생성물질이 검출되었다. 그러나 포틀란트 시멘트와 혼합한 경우가 강도가 가장 크게 나타났다. 반면에 고분자폴리머만 사용한 경우는 강도가 매우 낮았다. 따라서 시멘트를 일정 비율로 배합한 다른 재료를 첨가한 실험을 행하여 그 물성을 검토하였다 물질의 화학적인 특성을 고려하여 포졸란반응이 잘 일어날 수 있을 것으로 생각되는 여러 재료를 선정하여 많은 조합에 대한 실험을 행하였다. 생석회, 석고, 고령토, 규조토, 제올라이트 등의 여러 재료를 여러 조합으로 첨가하여 실험한 결과, 시멘트와 석고를 혼합한 것이 비교적으로 높은 압축강도를 나타내었다. 그리고 이러한 연구 결과를 바탕으로 연약점도의 고화에 최적인 조합과 배합비를 위한 실험을 재차 실시하였으며, 실험 후의 물성과 함께 반응생성물에 대한 검토도 행하여 그 결과를 발표하고자 한다.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 1999.11a
• /
• pp.177-182
• /
• 1999

사용한 보수.보강재, Rod, Fabric, Strand 형상을 콘크리트 구조물등에 보강재로 사용되어왔다. 이 재료는 해양환경하에서 내식성과 내구성을 갖는 철근및 철골대체용 복합소재와 초고층 경량 연속섬유보강 시멘트 복합재료는 탄소섬유, 아라미드섬유, 유리섬유등의 쉬트(sheet)형상을 신건재, 비자성, 비전도성, 전파차폐용 재료등에 사용할수있다. 그러나 FRP Rod를 내식성이 요구되는 철근 및 철골대체재로 사용할 경우에는 폴리머 매트릭스의 열화, 섬유와 폴리머간 계면 접착강도의 한계, 화재시 내화성, 보강재의 인발성등의 단점들을 갖고있다[1]. (중략)

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2013.11a
• /
• pp.106-107
• /
• 2013

The purpose of this study is to characterize the bonding properties between reinforced bar and re-emulsion polymer cement mortar through the pull off test. The properties of polymer cement mortar before and after hardening were measured. Spiral reinforced steel bar was used to control the brittleness fracture of test specimens. In addition polymer content as experimental factors, the types of reinforced bar and corrosion were considered as well. Non linear FEM analysis was carried out to expect the behavior of bonding interface under the certain load.

• Korean Journal of Agricultural Science
• /
• v.25 no.2
• /
• pp.278-284
• /
• 1998

This study was performed to evaluate the engineering properties of permeable polymer concrete with Fly Ash and $CaCo_3$. The following conclusions were drawn; 1. The unit weight was in the range of $1,830{\sim}1,932kgf/m^3$, the unit weights of those concrete were decreased 16~20% than that of the normal cement concrete. 2. The highest strength was achieved by fly ash 50% and $CaCo_3$ 50% filled permeable polymer concrete, it was increased 26% by compressive strength, 121% by tensile strength and 275% by bending strength than that of the normal cement concrete, respectively. 3. The ultrasonic pulse velocity was in the range of 2,805~2,904m/s, which was showed about the same compared to that of the normal cement concrete. Fly ash 50% and $CaCo_3$ 50% filled permeable polymer concrete was showed higher pulse velocity.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2010.05a
• /
• pp.69-70
• /
• 2010

• Korean Journal of Agricultural Science
• /
• v.26 no.2
• /
• pp.49-55
• /
• 1999

This study is performed to evaluate the properties of permeable polymer concrete with blast furnace slag and fly ash. The following conclusions are drawn: 1. The highest strength is achieved by 50% filled blast furnace slag powder and fly ash permeable polymer concrete, it is increased 36% by compressive strength and 217% by bending strength than that of the normal cement concrete, respectively. 2. The static modulus of elasticity is in the range of $100{\times}10^3{\sim}130{\times}10^3kgf/cm^2$, which is approximately 43~51% of that of the normal cement concrete. 3. The dynamic modulus of elasticity is in the range of $102{\times}10^3{\sim}130{\times}10^3kgf/cm^2$, which is approximately less compared to that of the normal cement concrete. The highest dynamic modulus is showed by 50% filled blast furnace slag powder and fly ash permeable polymer concrete. The dynamic modulus of elasticity are increased approximately 0~4% than that of the static modulus. 4. The water permeability is in the range of $4.612{\sim}5.913l/cm^2/h$, and it is largely dependent upon the mix design.

• Resources Recycling
• /
• v.27 no.6
• /
• pp.59-67
• /
• 2018

Efflorescence is a white deposit of powders in the surface of cement concrete which can also occur in geopolymers. Efflorescence occurs when sodium ions in alkali activator react with atmospheric carbon dioxide to form sodium carbonate components. In this study, we investigated whether the secondary efflorescence can be reduced by controlling the Na/Al mole ratio or by changing the curing temperature and heat curing time in fly ash-based geopolymers. The 28 days compressive strength in geopolymers having Na/Al ratio of 1.0 was higher than geopolymers having Na/Al ratio of 0.8. The strength increased with the increasing curing temperature and longer heat curing time. On the other hand, efflorescence was lower when the curing temperature was high and the heat curing time was longer in the geopolymers having Na/Al ratio of 1.0. The geopolymers having Na/Al ratio of 0.8 showed accelerated efflorescence occurrence than the geopolymers having Na/Al ratio of 1.0. In order to reduce the occurrence of the secondary efflorescence of fly ash-based geopolymers, it will be advantageous to maintain the Na/Al ratio at 1.0, increase the curing temperature, and lengthen the heating curing time.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.9 no.4
• /
• pp.235-242
• /
• 2005

This study is on the evaluation of performance of polymer cement mortar which is used for pre-wetting spray method. Pre-wetting spray method is an epoch-making method to repair concrete structures damaged, which is added a small quantity water preciously to dry mortar to reduce dust and rebound and spray mortar mixed with fixed quantity water at nozzle before spray. The result showed that physical performance such like compressive, flexural and adhesive strength of polymer cement mortar, TS 100 used for pre-wetting spray method was superior to other repair mortar. Also durable performance such as resistance on permeability of chloride ion, carbonation, chemical and freezing-thawing was excellent.