• Proceedings of the SAREK Conference
• /
• 2008.11a
• /
• pp.55-60
• /
• 2008

Turbulent flow characteristics on the gap of two parallel channels are investigated using LES(large eddy simulation) approach. Two parallel channels have the same cross-section area and are connected by the narrow channel named the gap. Turbulent flow near the gap makes the flow pulsation along the streamwise direction of two channels. The flow condition is the Reynolds number of $2.5{\times}10^{-5}$. We compared the predicted results with the previous experimental results and presented the axial mean velocity, turbulent intensities, Reynolds shear stresses and turbulent kinetic energy.

• The Journal of Korean Academy of Prosthodontics
• /
• v.8 no.1
• /
• pp.48-55
• /
• 1968

1958년(年) Fullmer와 $Lillie^9$에 의(依)하여 최초(最初)로 보고(報告)된 Oxytalan 섬유(纖維)는 산(酸)에 내성(耐性)이 강(强)한 섬유(纖維)로 치근막(齒根膜)에 많이 출현(出現)하고 기계적(機械的) 자극(刺戟)에 의(依)하여 배열(配列), 주행(走行) 및 수적(數的)인 변화(變化)를 가져온다. 저자(著者)는 교정력(矯正力)을 이용(利用)하여 치아(齒牙)를 이동(移動) 시킨후(後) 치근막내(齒根膜內) Oxytalan섬유(纖維)의 수(數), 주행(走行) 및 형태(形態)의 변화(變化)를 실험적(實驗的)으로 관찰(觀察)한바 있어 이를 보고(報告)하는 바이다. 본연구(本硏究)에 사용(使用)된 실험동물(實驗動物)로는 체중(體重) 60gram내외(內外)의 자성백서(雌性白鼠) 15마리를 택(澤)하였다. 각동물(各動物)은 Ether마취후(麻醉後) 교정용(矯正用) 고무줄편(片)을 상악우측(上顎右側) 제1구치(第一臼齒)와 제2구치(第二臼齒) 사이에 삽입(揷入)하여 24, 48, 72시간(時間) 간격(間隔)으로 관찰(觀察)하였다. 동물(動物)을 도살후(屠殺後) 상악골(上顎骨)을 적출(摘出)하여 10%중성(中性) 호루마린에 고정후(固定後) 3%의산(蟻酸)으로 탈회(脫灰)하였다. 파라핀 포매후(包埋後) 근원심적(近遠心的)으로 $4{\sim}6{\mu}$의 절편(切片)을 만들어 Hematoxylin-eosin 및 Aldehyde fuchsin염색(染色)을 시행(施行)하여 경험(鏡險)한 결과(結果)는 하기(下記)와 같다. 1. 치아이동후(齒牙移動後) 교원성섬유(膠原性纖維) 및 Oxytalan섬유(纖維)들의 배열(配列)에 있어 뚜렷한 차이(差異)를 보였다. 2. 치아이동후(齒牙移動後) 사주섬유(斜走纖維)는 염박측(壓迫側)에서는 치아장축(齒牙長軸)에 수직(垂直)되게, 견인측(牽引側)에서는 평행(平行)되게 주행(走行)하고 있었다. 3. 48시간군(時間群)에서 세포증식(細胞增殖)이 심(甚)하였다. 4. Oxytalan섬유(纖維)는 치아(齒牙)들에 교정력(矯正力)을 가(加)한후(後) 견인(牽引) 염박(壓迫) 양측(兩側) 공(共)히 수(數)가 증가(增加)하였다. 5. 염박측(壓迫側)에서 Oxytalan섬유(纖維)는 속(束)을 형성(形成)하며 치아장축(齒牙長軸)에 평행(平行)되게 주행(走行)하였다. 6.견인측(牽引側)에서는 하나 또는 두세개의 섬유(纖維)들이 산발적(散發的)으로 치아장축(齒牙長軸)에 평행(平行)되게 하였다. 7. Oxytalan섬유(纖維)의 수(數)는 염박측(壓迫側)에서 보다 견인측(牽引側)에서 더 변화(變化)가 많았다.

• Journal of the Korean GEO-environmental Society
• /
• v.2 no.1
• /
• pp.37-56
• /
• 2001

As a preliminary study to establish fracture network model in crystalline rocks, detail investigation on fracture characteristics were performed. Five fracture sets were determined on the basis of regional survey of geological structures and fractures on outcrops. Among the fracture sets, S1 set has the highest density and longest trace length of fractures which was identified on surface in the study area. S4 and S5 sets are composed of foliations and foliation parallel shear joints of gneisses, which are very important sets at the aspect of weighting of fracture length. For characterization of subsurface fractures, detail core logging was performed to identify fractures and fracture zones from five boreholes. Acoustic televiewer logging and borehole geophysical loggings produced images, orientations and geophysical properties of fractures which intersect with boreholes. According to the result of the investigations, subsurface fractures can be grouped as three preferred orientations(B1, B2 and B3), which correspond to S1, S2 and S4/S5 of surface fracture sets, respectively. Actually, B1 set is expected to be intensely developed at subsurface. However, it has low frequency of intersection with boreholes due to its parallel or sub-parallel direction to boreholes. According to the inference of conductive fractures, B1 and B3 sets have possibilities of water flow and their intersection lines are also thought to consist of important conduits of groundwater flow. In particular, faults which are parallel to foliations control major groundwater flow in the study area.

• Radiation Oncology Journal
• /
• v.21 no.4
• /
• pp.322-329
• /
• 2003

Purpose: It is difficult to exactly determine the surface dose and the dose distribution In buildup region of high energy X-rays by using the conventional ion chamber. The aim of this study Is to evaluate the accuracy of widely used dosimetry systems to measure the surface dose and the depth of maximum dose (d$_{max}$). Materials and Methods: We measured the percent depth dose (PDD) from the surface to the d$_{max}$ in either a water phantom or in a solid water phantom using TLD-100 chips, thimble type ion chamber, diode detector, diamond detector and Markus parallel plate ion chamber for 6 MV and 15 MV X-rays, 10$\times$10 cm$^{2}$, at SSD=100cm. We analysed the surface dose and the d$_{max}$. In order to verify the accuracy of the TLD data, we executed the Monte Carlo simulation for 5 MV X-ray beams. Results: The surface doses In 6 MV and IS MV X-rays were 29.31% and 23.36% ior Markus parallel plate ion chamber, 37.17$\%$ and 24.01$\%$ for TLD, 34.87$\%$ and 24.06$\%$ for diamond detector, 38.13$\%$ and 27.8$\%$ for diode detector, and 47.92$\%$ and 35.01$\%$ for thimble type ion chamber, respectively. in Monte Carlo simulation for 6 MV X-rays, the surface dose was 36.22$\%$, which Is similar to the 37.17$\%$ of the TLD measurement data. The d$_{max}$ In 6 WV and 15 MV X-rays was 14$\~$16 mm and 27$\~$29 mm, respectively. There was no significant difference in the d$_{max}$ among the detectors. Conclusion: There was a remarkable difference in the surface dose among the detectors. The Markus parallel plate chamber showed the most accurate result. The surface dose of the thimble ion chamber was 10$\%$ higher than that of other detectors. We suggest that the correction should be made when the surface dose of the thimble ion chamber Is used for the treatment planning ion the supeficial tumors. All the detectors used In our study showed no difference in the d$_{max}$.

• Journal of Biomedical Engineering Research
• /
• v.25 no.3
• /
• pp.207-215
• /
• 2004

A finite element analysis is used in this study to model 6 kinds of electrode by a genetic program in order to evaluate the mechanical effect on the 3D human cochlea model and the behavior of electrode. Human cochlea is modeled by the spiral-approximation method and the shape of scala tympani is extracted from the mid section of the human cochlea. Contact pressure at the tip and the insertion force are found to be highest when the wires stack horizontally. Axial rotation of electrode is minimal comparing with the stimulating current spread. The results indicate that the electrode stiffness is important to minimize the trauma.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1998.05b
• /
• pp.243-249
• /
• 1998

상용 핵연료 피복관 재료로 사용되고 있는 Zircaloy-2와 Zircaloy-4 및 ZIRLO$^{TM}$에 대한 수소와의 반응거동 및 속도론적(kinetic) 자료를 얻기 위하여 electro-microbalance가 장착된 TGA (thermogravimetric analysis) 장치를 이용하여 30$0^{\circ}C$~50$0^{\circ}C$의 온도범위에서 1기압 수소와의 반응에 따른 무게증가를 in-situ로 측정하였다. Zircaloy와 수소와의 반응거동은 chamber내 온도상승시 생성되는 산화막에 의해 초기에는 느린 반응이 진행되는 영역이 존재하고 온도가 낮은 35$0^{\circ}C$ 이하에서는 이것이 잠복기 형태로 나타난 후 직선속도법칙(linear rate law)을 따르며 반응이 가속화되는 것으로 나타났고 40$0^{\circ}C$ 이하의 저온에서는 직선속도법칙에서 반응이 지연되는 방향으로 약간의 편차(deviation)가 관찰되었다. 그 결과 Zircaloy-2와 ZIRLO$^{TM}$가 Zircaloy-4보다 수소와의 반응속도가 빠르고 활성화에너지가 낮은 것으로 나타났으며 직선속도법칙을 근거로 하여 각각 1.1x$10^{7}$ exp(-20,800/RT)와 1.5x$10^{6}$exp(-18,000/RT) 및 6.9x$10^{7}$ exp(-23,800/RT) (mg/dm$^2$/min) 의 속도상수를 도출하였다. 또한, 열구배가 존재하지 않는 out-of-pile 조건하에서도 'sunburst' 형태의 국부적 수소침투가 발생할 수 있음이 ～l,000 ppm이상의 수소침투 시편에서 확인되었다. ～3,000ppm이상 침투하게 되면 표면에 수소화물이 농축되어 있는 hydride layer가 형성됨을 관찰하였으며 ～5,000ppm 이상의 경우에는 수소화물의 방향성이 random하였으며 특히, ZIRLO$^{TM}$ 시편의 경우에서는 원주방향으로 길게 이어진 수소화물과 기계적 성질에 치명적인 반경방향의 수소화물이 평행하게 배열된 것을 관찰하였다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.4 no.2
• /
• pp.133-142
• /
• 1984

With the weld-joined compact tension specimens compared with each other, that is, transverse and lengthwise about the crack propagation direction, high and low in the input heat level, same as and lower than the base metal in the strength of weld material, the fatigue test were performed. With these data, the log-log curves between the fatigue crack propagation rate ${\frac{da}{dN}}$ and the transition range of the stress intensity factor ${\Delta}K$ ahead the crack tip were drawed. These curves were compared and estimated among each compared specimens, among each zones, that is, the base metal, the heat-affected metal and the weld-mixed metal, and between this study and the past studies. Basically, Little difference in the slope of the $da/dN-{\Delta}K$ relation was showed in all the welded directions, all the input heat levels and all the zones. But, First, to comparison with in the past studies about the base metals, it was showed that da/dN started in the much later rate, increased faster and stoped in the little faster rate. Second, it was showed that, near the time the crack's going from the heat-affected zone to the weld-mixed metal da/dN decreased a little for a while. Third, in the lengthwise weld compared with the transverse weld, in the high input heat weld compared with the low input heat weld in the case used the weld material of the same strength as the base metal, in the opposite case in the case used the one of the lower strength than the base metal, in the case used the weld material of the same strength as compared with the lower strength than the base metal beside the high input heat and the lengthwise weld, it was showed that the crack occured earlier in lower ${\Delta}K$ and later da/dN, the curves went with the same slope. Forth, in the lengthwise weld compared with the transverse weld in the low input heat weld, in the low input heat weld compared with the high input heat weld, it was showed that da/dN went with the lower level.

• Journal of KIISE:Software and Applications
• /
• v.26 no.11
• /
• pp.1314-1323
• /
• 1999

컴퓨터의 사용이 일반화됨에 따라 데이타를 생성하고 수집하는 것이 용이해졌다. 이에 따라 데이타로부터 자동적으로 유용한 지식을 얻는 기술이 필요하게 되었다. 데이타 마이닝에서 얻어진 지식은 정확성과 이해성을 충족해야 한다. 본 논문에서는 데이타 마이닝을 위하여 퍼지 결정트리에 기반한 효율적인 퍼지 규칙을 생성하는 알고리즘을 제안한다. 퍼지 결정트리는 ID3와 C4.5의 이해성과 퍼지이론의 추론과 표현력을 결합한 방법이다. 특히, 퍼지 규칙은 속성 축에 평행하게 판단 경계선을 결정하는 방법으로는 어려운 속성 축에 평행하지 않는 경계선을 갖는 패턴을 효율적으로 분류한다. 제안된 알고리즘은 첫째, 각 속성 데이타의 히스토그램 분석을 통해 적절한 소속함수를 생성한다. 둘째, 주어진 소속함수를 바탕으로 ID3와 C4.5와 유사한 방법으로 퍼지 결정트리를 생성한다. 또한, 유전자 알고리즘을 이용하여 소속함수를 조율한다. IRIS 데이타, Wisconsin breast cancer 데이타, credit screening 데이타 등 벤치마크 데이타들에 대한 실험 결과 제안된 방법이 C4.5 방법을 포함한 다른 방법보다 성능과 규칙의 이해성에서 보다 효율적임을 보인다.Abstract With an extended use of computers, we can easily generate and collect data. There is a need to acquire useful knowledge from data automatically. In data mining the acquired knowledge needs to be both accurate and comprehensible. In this paper, we propose an efficient fuzzy rule generation algorithm based on fuzzy decision tree for data mining. We combine the comprehensibility of rules generated based on decision tree such as ID3 and C4.5 and the expressive power of fuzzy sets. Particularly, fuzzy rules allow us to effectively classify patterns of non-axis-parallel decision boundaries, which are difficult to do using attribute-based classification methods.In our algorithm we first determine an appropriate set of membership functions for each attribute of data using histogram analysis. Given a set of membership functions then we construct a fuzzy decision tree in a similar way to that of ID3 and C4.5. We also apply genetic algorithm to tune the initial set of membership functions. We have experimented our algorithm with several benchmark data sets including the IRIS data, the Wisconsin breast cancer data, and the credit screening data. The experiment results show that our method is more efficient in performance and comprehensibility of rules compared with other methods including C4.5.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.12 no.1
• /
• pp.43-50
• /
• 1992

The purpose of this study is to ascertain the robustness of p-version model with hierarchic intergrals of Legendre shape functions in various applications including plane stress/strain, axisymmetric and shell problems. The most important symptoms of accuracy failure in modern finite elements are spurious mechanisms and a phenomenon known as locking which are exhibited for incompressible materials and irregular shapes which contain aspect ratios(R/t, a/b), tapered ratio(d/b), and skewness. The condition numbers and energy norms are used to estimate numerical errors, convergence characteristics and algorithmic efficiencies for verifying the aforementioned symptoms of accuracy failure. Numerical results from p-version models are compared with those from NASTRAN, SAP90, and Cheung's hybrid elements.

• Fire Science and Engineering
• /
• v.29 no.3
• /
• pp.21-30
• /
• 2015

In this study, we try to suggest measures to reduce leakage at a joint between CPVC piping for a sprinkler system and a pipe expansion through reviews of domestic and foreign standards and related tests. The quality of the waterproof rubber packing material between a valve socket and pipe expansion nut was examined. In the leak test, the valve socket material over the expansion part of the metal pipe nut was found to use a metal part or a schlorinated polyvinyl chloride pipe nut part. In addition, the KS B 0221 standard for parallel pipe threads with threaded and thread inspection criteria and inspection standards in order to ensure an acceptable quality of valve socket, there is a need to amend the regulations to comply with the KS B 5223 (screw thread limit gauges parallel pipe threads). We do not have detailed standards for expansion piping nuts for waterproof rubber ring material, so we need to amend the relevant criteria for EPDM material to be used with excellent waterproofing, for which both NBR and EPDM are currently used.