• Journal of the Korean Institute of Gas
• /
• v.9 no.1 s.26
• /
• pp.33-37
• /
• 2005

This paper deals with parametric studies for the structural response of LNG Storage Tank steel roof behavior acoording to change in design condition. In the design of steel roof, it may be required to represent a stable behavior under many loading conditions and those of combinations. We fulfill the analysis the steel roof behavior during concret placing and additionally change the design variabls like H beam, pressure and steel roof plate thickness. On the basis of the obtained results from this studies a guideline for a more reasonable design of LNG storage tank steel roof is introduced.

• Aerospace Engineering and Technology
• /
• v.2 no.1
• /
• pp.213-222
• /
• 2003

Some analytical methods to analyze low-velocity impact force history of composite laminated structures used in aerospace vehicles are reviewed. A classical method used at initial research of low-velocity impact problem in 1980s was reviewed on its physical meaning, and the approximate method assuming the shape of impact force history as a sinusoidal wave was reviewed. A parametric study on contact constant and exponent in contact law was performed in order to analyze an effect on impact force history, and finally its was understood that impact force history could be analyzed accurately even though the linearized contact law was used. Also, in this paper it was shown that impact problem could be analyzed simply and easily using a commercial finite element code.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.3
• /
• pp.397-408
• /
• 1988

The study is concerned with the theoretical and experimental investigation of the elliptical bulge test. The elliptical bulge test is analyzed by using a rigid-plastic finite element method incorporating large deformation and normal anisotropy. Thin elliptical diaphragms of mild steel are bulged for three aspect ratios. The contact problem the die round and the sheet is successfully solved by using a skew boundary condition. It is shown that the proper consideration of die radius and normal anisotropy is very significant. The relation between bulging pressure and deformation is obtained. It has been found that the pole is nearly under proportional straining during deformation. The instability criterion by maximum load condition enables the effective prediction of instability pressure. The computional results are in good agreement with experimental results and to be very useful for a better understanding of the elliptical bulge test.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.6 no.1
• /
• pp.35-41
• /
• 1986

A hybrid modelling technique of a soil-structure system on viscoelastic soil medium is studied in this paper. The hybrid model consists of a near-field and a far-field with their common interface passing through the soil region at some distance from the base of the structure. It makes use of frequency-dependent impedances so as to represent the semi-infinite far-field. The far-field impedances are formulate including the radiation damping characteristics as well as the viscoelastic properties of the soil medium. The verification of the method has been carried out using a rigid circular plate on a viscoelastic half-space. The impedances obtained by the method are compared with the theoretical values. Example analyses have been performed for a tall chimney and the results have been compared with those obtained by other methods which are frequently used.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.5 s.176
• /
• pp.1103-1114
• /
• 2000

Recent attempt to enhance the safety against collision reshaped the simple shell structures into the integrated complex shell structures. Moreover, due to various regulations continuously tightened for environment protection, weight reduction of automobiles becomes an increasingly important issue. Auto parts lightening is mainly accomplished by more reasonable design, adoption of lighter materials and miniaturization of the auto bodies. Focusing on the locally enhanced design approach among the above three ways, we here attempt to develop a patching optimization method, and also to determine the thicknesses of an integrated shell structure, both bringing a specified amount of stress relaxation. We first select a cross member as a patching optimization model. Based on the finite element stress calculations, we relieve the stress of cross member by patching in two ways-nonuniform thickness patching and optimized uniform thickness patching, the latter of which is more effective in a practical point of view for the preset amount of stress relaxation. Selecting a box type subframe as another finite element analysis model, we then determine the thickness of each part by axiomatic design approach for a preset amount of stress relaxation. The patching methodology and the axiomatic approach adopted in this work can be applied to the other complex shell structures such as center member and lower control arm.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.7
• /
• pp.877-884
• /
• 2004

In this paper, structural analysis is performed to investigate the deformation of porous media in a proton exchange membrane fuel cell (PEMFC). Structural deformation of air plate of the fuel cell causes the change in configuration and cross sectional area of the channel. The distributions of mass flow rate and pressure are major factors to decide the performance of a PEMFC. These factors are affected by channel configuration of air plate. Two kinds of numerical air plate models are suggested for flow analyses. Deformed porous media and undeformed porous media are considered for the two models. The Numerical flow analysis results between deformed porous media and undeformed porous media have some discrepancy in pressure distribution. The pressure and velocity distribution under a working condition are numerically calculated to predict the performance of the air plates. Pressure and velocity distributions are compared for two models. It is shown that structural deformation makes difference in flow analysis results.

• Journal of the Society of Naval Architects of Korea
• /
• v.57 no.2
• /
• pp.70-79
• /
• 2020

The offshore installation units may be subjected to various accidental loads such as collision from supply vessels, impact from dropped objects, blast load from gas explosion and thermal load from fire. This paper deals with the design and strength evaluation method of the stiffened plate structures in response to a blast load caused by a gas explosion accident. It is a comprehensive review of various items used in actual project such as the size and type of the explosive loads, general design procedure/concept and analysis method. The structural analyses using simple analysis methods based on SDOF model and nonlinear finite element analysis are applied to the particular FPSO project. Also validation studies on the design guidance given by simple analysis method based on SDOF model have also considered several items such as backpressure effects, material behavior and duration time of the overpressure. A good correlation between the prediction made by simple analysis method based on SDOF model and nonlinear finite element analysis can be generally obtained up to the elastic limit.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.1651-1654
• /
• 2008

Previous reports have introduced the technique of spinous process osteotomy to decompress spinal stenosis, a procedure which aims to afford excellent visualization while minimizing destruction of tissures not directly involved in the pathologic process. However, bio-mechanically it has not been investigated whether the sacrifice of posterior spinous process might have potential risk of spinal instability or not, even though supra-spinous and inter-spinous ligament are preserved. Therefore the aim of this study is to evaluate the bio-mechanical properties after spinous process osteotomiy, using finite element analysis. In the model of spinous process osteotomy the increase of stress in the disc and segmental rangesof motions were not changed significantly. It is due to the fact that the instability of lumbar spine has been maintained by the two-types of ligaments compared with the prior surgical technique. Therefore, according to the finite element result on this study, these osotetomy was considered to be a clinicallysafe surgical procedure and could not cause the instability of patient.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.1
• /
• pp.52-57
• /
• 2007

One of the hot issues in composite patching is to reduce the thermal residual stresses between composite patch and aluminum surface which occurs after bonding of composite patch. In this study, the edge crack patching is adopted for different curing cycles. For the analysis, three layer Mindlin plate elements are used, and Paris' law is adopted to predict the fatigue life of composite patch plate. The analysis results show a good agreement with the experimental fatigue life and this technique can be applied for the prediction of fatigue life of aircraft structures.

• Journal of Korean Society of Steel Construction
• /
• v.12 no.4 s.47
• /
• pp.407-416
• /
• 2000

This paper presents the dynamical responses of the plate girder bridge subjected to moving load by experimental method. The upper slab of the plate girder bridges is modelled to the plate element and the girder to the beam element. The small-scaled vehicle model is manufactured as moving load and the acryl-bridge model as the plate-girder bridge. The dynamic responses of the plate-girder bridges under the moving load are obtained by the strain gauges, displacement measurements, accelerometer, and dynamic strain measurement. The maximum dynamic responses from the measured data are compared with those from the finite element method. The experimental model test can be used to obtain to the dynamic responses of the plate-girder bridges.