• Geophysics and Geophysical Exploration
• /
• v.10 no.2
• /
• pp.131-137
• /
• 2007

With consideration of the first arrival picking methodology and inherent errors in picking process, I propose, from the computerization point of view, a practical algorithm for picking and error computation. The proposed picking procedure consists of 2-step; 1) picking the first coherent peak or trough events, 2) derive a line which approximates the record in the interval prior to the pick, and set the intercept time of the line as the first break. The length of fitting interval used in experiment, is few samples less than 1/4 width of the arriving wavelet. A quantitative measure of the error involved in first arrival picking is defined as the time length that needed to determine if an event is the first arrival or not. The time length is expressed as a function of frequency bandwidth of the signal and the S/N ratio. For 3 sets of cross-well seismic data, first breaks are picked twice, by manually, and by the proposed method. And at the same time, the error bound for each trace is computed. Experiment results show that good performance of the proposed picking method, and the usefulness of the quantitative error measure in pick-quality evaluation.

• Geophysics and Geophysical Exploration
• /
• v.10 no.4
• /
• pp.299-307
• /
• 2007

Slowness time coherence (STC) technique has been applied to 3-receiver slim hole sonic log using 3 NX sized concrete model holes of different physical properties. We analyzed the effects of different source center frequencies on the wave forms, their amplitude spectra, and their STC results. We could determine the sonic velocity of each mode accurately by the application of STC method with the semblance projection and efficient selection of center frequency. Theoretical model and experimental model hole studies indicate that 4-receiver condition is the most ideal for STC in near surface slim hole sonic log. The result also indicates that favorable STC result can be obtained from three-receiver sonic log provided with the help of the first arrival picking method.

• Journal of the Society of Naval Architects of Korea
• /
• v.28 no.2
• /
• pp.187-194
• /
• 1991

Vibration analysis methods of a beam-column with elastically restrained ends and various intermediate constraints such as rectilinear springs, rotational springs and concentrated masses are presented. Firstly, an exact method of solutions based on Hamilton's principle and Laplace transform method is shown. This method of solutions is very complicate in cases of having Intermediate constraints more than two. Therefore, Rayleigh-Ritz method using the eigenfunctions of the base system, the system without intermediate constraints, are also investigated. Extensive numerical examples carried out for comparisons with known published works show that the latter method has easy adaptability for wide varieties of boundary conditions and intermediate constraints, and gloves good accuracy for various intermediate constraints with reasonable number of terms in construction of a trial function.

• Journal of the Society of Naval Architects of Korea
• /
• v.29 no.3
• /
• pp.140-148
• /
• 1992

The free vibration problem of symmetrically laminated composite rectangular plates is formulated based on anisotropic thick plate theory including the effects of shear deformation and rotary inertia. Considering the difficulty of obtaining closed-form solutions, Rayleigh-Ritz analysis using polynomials having the property of Timoshenko beam functions as trial functions is adopted. The boundary conditions elastically restrained against rotation are accomodated as well as classical boundary conditions. From the results of numerical studies, the validity of the present method is verified. And it is also found that the adoption of thick plate theory for the vibration analysis of laminated composite plates is essential because of the relatively large shear deformation effect, and that the convergence of the Rayleigh quotient to the stationary value is less rapid in anisotropic composite plates than that in the orthotropic ones due to more complicated mode shapes of the former.

• Journal of the Korea Society of Computer and Information
• /
• v.18 no.1
• /
• pp.93-101
• /
• 2013

The accurate detection of R-wave is important for other feature extraction in ECG, and R-wave has a lot of medical information about heart. Numerous R-wave detection algorithms have been studied on the ECG signal shape analysis, but it was difficult to find accurate R-wave when the shape of R-wave is similar to the shape of P-wave. This paper presents an R-wave detection method based on the refractory period that is the period of depolarization and repolarization of the cell membrane after excitation. And we also use the shape of kurtosis in the refractory period. The proposed method is validated using the ECG records of the MIT-BIH arrhythmia database. Experimental results show that the proposed method significantly outperforms other method in case of 105 and 108 record that have R-wave similar to P-wave, as well as other records.

• Journal of the Korean Magnetics Society
• /
• v.23 no.4
• /
• pp.135-143
• /
• 2013

The clip-type pulsimeter equipped with a Hall sensor has a permanent magnet attached in the "Chwan" position to the center of a radial artery. The clip-type pulsimeter is composed of a hardware system measuring voltage signals. These electrical bio-signals display pulse rate, non-invasive blood pressure, respiratory rate, pulse wave velocity (PWV), and spatial pulse wave velocity (SPWV) simultaneously measured by using the radial artery pulsimeter, the electrocardiograph (ECG), and the photoplethysmograph (PPG). The findings of this research may be useful for developing a oriental-western biomedical signal storage device, that is, the new and fusion patient monitor, for a U-health-care system.

• Journal of the Institute of Electronics Engineers of Korea TE
• /
• v.37 no.1
• /
• pp.50-57
• /
• 2000

By supporting wireless communication technology, there is gradually expansion of the commercial application for Wireless Local Loop(WLL) technology, which is to replace existing telephone line with wireless one. The WLL system application helps a operator to have merits of the installation and maintenance of line and also a subscriber to make a high speed value-added service. As mentioned above reasons for both sides, many manufactories and operators are concerned with development and application respectively. This paper presents hardware implementation of Radio Port Controller(RPC) and also describes the system configuration, functions, and Inter Processor Communication(IPC) structure of RPC. We performed inter-module communication test via IPC backplane bus. And inter-module integration test also completed through data communication and signal waveform measurement repeatedly.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.2
• /
• pp.73-78
• /
• 2011

A frequency synthesizer for DAB applications is designed using $0.18{\mu}m$ CMOS process with 1.8V supply. NP-core type is chosen for VCO core to improve low power characteristic and symmetric characteristic of output waveform. VCO range is 1302.34 MHz - 1949.51 MHz using switchable capacitor bank and varactor bank. Varactor biases that improve varactor capacitance characteristics were minimized as two, $K_{vco}$(VCO gain) is maintained using technique of varactor bank switching. Intervals of $K_{vco}$ are maintained adding VCO frequency compensation logic. Each block of VCO and frequency synthesizer designed $0.18{\mu}m$ CMOS process with 1.8V supply is verified by Cadence Spectre, measured VCO consumes 9mA current, and is 39.8% tuning range, total power consumption of the frequency synthesizer is 18mW.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.9
• /
• pp.34-39
• /
• 2007

Serial links via backplane channels suffer from severe signal integrity problems which are normally caused by channel imperfections, such as flat loss, frequency-dependent loss, reflection, etc. Particularly, the frequency-dependent loss causes ISI(Inter-Symbol-Interference) at signal waveforms. Therefore, adaptive equalizing techniques have been exploited in many products to facilitate the ISI problem. In this paper, we present an analog adaptive equalizer circuit designed in a $0.18{\mu}m$ CMOS process. It achieves 10Gb/s data transmission through a long 34-inch backplane channel(or transmission line). The post-layout simulations demonstrate $8ps_{p-p}$ jitter with 10mW power dissipation. The core of the adaptive equalizer occupies the area of $0.56mm^2$.

• Journal of the Society of Naval Architects of Korea
• /
• v.35 no.1
• /
• pp.88-97
• /
• 1998

Large aluminium extrusions can be used in rolling stocks and high speed vessels to reduce weight and labor cost. As sandwich plates with corrugated core have enough strength in transverse and longitudinal direction, welding lines to connect members are reduced and transverse members to strength longitudinal members are not required. However, for proper design of aluminium extrusion plates, understanding of structural behaviors of the exclusions are necessary. In this paper, at first, detailed finite element analysis is carried out to understand structural behavior. And then, simple theoretical formulas for design purpose are proposed using the orthotropic plate theory. Shear stresses resulting from end twisting which is characteristics of deep aluminium extrusion plates can also be calculated by the simple theoretical formula. Comparison with the results by detailed finite element analysis shows good accuracy of the proposed simple formulas. The simple formulas can be useful in repetitive analysis in the initial design stage.