• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.989-992
• /
• 2008

In this paper, we are presenting a case that integrates ultra high strength concrete(150MPa) with surface-exposed concrete. Ahead of the field application, we carried out laboratory experiment and B/P Test for a basic property of concrete(slump flow, air content, 50cm flow time, elapse time change and compression strength) and productivity. The next, we conducted Mock-up Test using simulation specimen to evaluate infilling, surface-finishing and hydration heat of concrete. We had satisfactory results for a basic property and hydration heat of concrete. However at the time of field application, it was occurred rupture of formwork because of high lateral pressure of concrete, and then formwork was reinforced and case-in-place time was adjusted. And regardless of low and high frequency vibration, it occurred to surface-pockmark. In case that applies ultra high strength concrete to surface-exposed concrete, we estimate that it is important of systematic management and improvement of construction.

• Journal of Korean Society of Forest Science
• /
• v.94 no.6
• /
• pp.377-386
• /
• 2005

This study was carried out to analyse the landslide characteristics by ground investigation, borehole image processing system, field seismic test, laboratory test and ground stability analysis at the landsliding area occurred in Maeri, Sangdong-myeon, Gimhaesi, Gyeongsangnam-do. Region I needs to install data logger system to monitor a land displacement during the heavy rainfall events because the region can be liable to occur the land slide by land creeping. It is needed to restore rapidly, if the land displacement occurs in Region I. Region II needs to monitor and repair because of the possibility of slope failure by long-term soil loss. Region III needs constructions to remove ground runoff and ground water to be infiltrated from talus. Region IV where is a stable region, needs to be protected from land cutting or other man-made damage.

• Journal of the Korean Geotechnical Society
• /
• v.21 no.5
• /
• pp.133-142
• /
• 2005

The research concentrates on improving the in-hole seismic probe, which has been developed in past five years, to be used in stiffness measurements of tunnel-face materials. The size of probe was reduced to be fit in 45-mm diameter holes (or BX) drilled by a jumbo-drill, which is used to drill holes to install explosives for tunneling. Also trigger system was improved by using a down-speeding motor for operating convenience and air packing system was replaced with a set of plate-springs to eliminate supply of compressed air. These modifications are to adjust the probe for the unfavourable environment inside of tunnels and to test without any further drilling cost. The probe and testing procedure were successfully adopted with horizontal holes drilled by a jumbo-drill at a tunnel-face to evaluate the stiffness of rock mass. The measured shear wave velocities can be used to estimate deformation properties of rock mass for tunnel analyses.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.11 no.1
• /
• pp.92-98
• /
• 1997

In this paper, the results of the measurement and analysis of extremely low freqency(ELF) eletric field in the vicinity of 154[kV] overhad transmission lines have been described. The planar-type electric field sensor has been fabricated by three dimensional structure with special consideration of taking the power frequency and lower components. The calibration experiments have been carried out according to the procedures of IEEE recommendation. The electric field measuring system has the frequency bandwidth of 7[Hz] to 2.7[MHz] and the response sensitivity of 0.094[mV/V/m]. Also the practical measurements of electric field under an 154[kV] double corcuit overhead transmission lines have been made abd abalyzed. It was known that the lateral electric field profiles under an 154[kV] double circuit overhead transmission lines show the asymmetrical distributions owing to the environmental metal frame structures and their maximum electric field magnitude is less than 3[kV/m]. It can be concluded that the measured results of the electric fields satisfy with all limits or guide -lines of the various authorized international institutes' recommendations.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.11 no.1
• /
• pp.14-23
• /
• 1997

In this paper, the results of the measurement and analysis of extremely low frequency(ELF) electric field in the vicinity of 154[kV] overhead transmission lines have been described. The planar-type electric field sensor has been fabricated by three dimensional structure with special consideration of taking the power frequency and lower components. The calibration experiments have been carried out according to the procedures of IEEE recommendation. The electric field measuring system has the frequency bandwidth of 7[Hz] to 2.7[MHz] and the response sensitivity of 0.094[mV/V/m]. Also the practical measurements of electric field under an 154[kV] double circuit overhead transmission lines have been made and analyzed. It was known that the lateral electric field profiles under an 154[kV] double circuit overhead transmission lines show the asymmetrical distributions owing to the environmental metal frame structures and their maximum electric field magnitude is less than 3[kV/m]. It can be concluded that the measured results of the electric fields satisfy with all limits or guidelines of the various authorized international institutes' recommendations.

• Journal of Sensor Science and Technology
• /
• v.7 no.4
• /
• pp.293-299
• /
• 1998

An objective of this study is to develop a voltage measuring device that uses a gas-filled switch (GS) on 22.9 kV-y extra-high voltage distribution lines. The voltage measuring device proposed in this paper is a kind of capacitive divider which consists of a detecting electrode attached outside of the bushing of GS, an impedance matching circuit, and a voltage buffer. It can be easily installed in an established GS without changing the structure. For the calibration and application investigations, the voltage measuring device was set up in the 25.8 kV 400 A GS, and a step pulse generator having 5 ns rise time is used. As a result, it was found that the frequency bandwidth of the voltage measuring device ranges from 1.35 Hz to about 13 MHz. The error of voltage dividing ratio which is evaluated by the commercial frequency voltage of 60 Hz was less than 0.2%. In addition, voltage dividing ratio in the commercial frequency voltage and in a non-oscillating impulse voltage were compared, and their deviation were less than 0.7%.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.8 no.1
• /
• pp.37-43
• /
• 1996

Breaking waves were generated in a 2-D flume. A piston-type wavemaker was operated in accordance with signals which consist of elementary harmonics with appropriate phase differences. These phase differences were estimated by using a linear wave theory so that wave crests were to be concentrated at the same position. The stroke of wavemaker was controlled to create plunging-type breaking waves. The signal with small amplitude could not generate breaking waves. In the case of moderate amplitudes, various breaking waves could be obtained. Most of breaking waves were spilling type. Only when the wavemaker was operated with appropriate amplitude, plunging-type breaking waves were generated. The parameters of breaking waves are the wave steepness and the frequency bandwidth. If the central frequency was low, breaking waves were not generated. Based on experimental data, we found that the wave height of breaking inception was H = 0.0113 gT$^2$. We also made computations by using a mixed Euler-Lagrangian scheme under the assumption of potential flow. The numerical results show good agreements with tank measurements.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.6 no.4
• /
• pp.375-388
• /
• 1994

When conducting movable bed tests in a narrow wave tank, the hydrodynamics and morphology are assumed to be two-dimensional; hence, any three-dimensional patterns such as cross-tank variations of the profiles are neglected or averaged to represent the mean profiles at the measuring time. In this paper, six movable bed tests were carried out with a fairly fine sand to investigate (1) whether or not three-dimensional features can occur in relatively narrow wave tanks, and (2) various possible interrelationships and causes of the three-dimensionality. These movable bed studies suggested that there was a relatively slow feedback between the hydrodynamics and the morphology that led to initiation and growth of 3-D morphological features, resulting in cross-tank profile variations under certain stages of profile development, especially when the profile approached an equilibrium with overall stability.

• Journal of The Geomorphological Association of Korea
• /
• v.19 no.2
• /
• pp.161-172
• /
• 2012

The Taeanhaean National Park is located on the middle of the west coast of Korean peninsula. Due to the relatively high wave energy, large tidal range which is about 7m, and extremely complex coastal line, various coastal land-forms such as mud-flats, sand beaches, sand dunes, sea cliffs etc. are well distributed in this area, and thus various coastal ecosystems are well preserved. However, because of reckless sand diggings and construction of artificial structures in the coastal zone, the natural flowing and exchange of coastal deposits were disturbed and the erosion in the beach and the dune has been seriously accelerated. To understand of the causes of these problems, we tried three times periodical measuring with VRS/RTK GPS instrument at the Hakampo and Anmyeon beach. According to seasonal changes of the coast-line, beach area and cross-section of study sites, generally erosion process was dominated in the summer and deposition process was followed after summer.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2018.05a
• /
• pp.45-45
• /
• 2018

오염물의 혼합거동을 해석하기 위해 물리기반 모델을 이용하는 경우 모델을 구축하고 운용하는데 많은 시간과 재정이 소요되며 현장검증을 통한 검증이 반드시 필요하다. 하지만 데이터 기반 모델의 경우 축적된 데이터만으로도 예측을 수행할 수 있으며 물리기반모델에 비해 결정해야할 입력인자가 적어 모델운용이 용이하다는 장점이 있다. 다양한 데이터 모델 중 인공신경망(ANN) 모델은 데이터가 가지는 불확실성 및 비정상성, 복잡한 상호관련성에 효과적으로 대응할 수 있는 모델로 수자원 및 환경 분야에서 자주 사용되고 있다. 본 연구에서는 인공신경망 모델을 이용하여 지천유입이 있는 대하천의 수질인자 (pH, 전기전도도, DO, chl-a)를 예측하였다. 다른 데이터기반 모델과 같이 인공신경망 모델 또한 수집된 데이터 질에 크게 영향을 받으며, 내부 입력인자의 선택이 모델의 예측 결과에 큰 영향을 미친다. 이러한 인공신경망 모델의 특성을 바탕으로 예측모형의 정확도를 향상하기 위해서는 크게 데이터 처리부분과 모델구축 부분에서의 접근이 필요하다. 본 연구에서는 데이터 처리 과정에서 연구대상지점의 각각의 수질인자가 가지는 분포 특성을 유지하기 위해 층화표츨추출법을 이용하여 데이터를 구성하였다. 모델의 구축 과정에서는 초기가중치 값의 영향을 줄이기 위해 앙상블기법을 사용하였으며, 좀 더 견고하고 정확한 결과를 예측하기 위해 탄력적 역전파알고리즘을 추가하였다. 추가적으로 합류 후 본류의 미 계측지역 수질 예측 정확도 향상을 위해 본류의 수질인자뿐만 아니라 지류의 수질인자를 입력자료로 사용하여 모의를 수행하였다. 또한 동일 구간에서 수행한 현장추적자실험 자료를 이용하여 수질인자의 분포특성을 비교, 검증하였다. 개발된 모델을 이용하여 낙동강과 금호강 합류부 하류의 수질인자를 예측한 결과 지류의 수질인자를 입력자료로 추가한 경우 예측의 정확도가 증가하였으며, 현장실험 자료를 통해 밝혀진 오염물의 거동현상을 인공신경망 모델로도 동일하게 재현하는 것으로 나타났다. 본 연구에서 제안한 인공신경모델을 이용한다면 물리기반 수치모델을 대체하여 지천으로 유입된 오염물의 거동을 정확하고 효율적으로 파악할 수 있을 것이다.