• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.8
• /
• pp.67-74
• /
• 2008

In this paper we describe discharge characteristics between needle-to-plane electrodes in water in various conditions such as different impulse voltages, polarities and water resistivities. Streamer corona is initiated at the tip of needle electrode and propagates toward plane electrode, and it experiences the final jump across the test gap. The branched channels of streamer coronas for lower water resistivities are much thicker and brighter than those for higher water resistivities at the same level of applied voltage. The negative streamer coronas not only have more branches but also widely spread out compared to the positive streamer coronas. A number of pulse-like currents ranging from some hundreds mA to a few A after streamer corona onset were produced with discharge developments. The time-lags-to breakdown for the positive polarity were remarkably shorter than those for the negative polarity. The pre-breakdown energy supplied into the test gap was inversely proportional to water resistivity.

• The KIPS Transactions:PartC
• /
• v.15C no.2
• /
• pp.119-124
• /
• 2008

The LEACH is a study method of a clustering base that was representative in many routing techniques that was suggested in sensor network environment. This is suggested technique to manage the sensor network group which consisted of many sensors in efficiency. However, it does not consider energy remaining quantity of the cluster header to manage cluster group, the problem where the cluster group is able to destroyed on the middle which transmits data. We are going to propose to solve such a problem by this paper for new clustering technique to accomplish management for a cluster group. It uses the technique which it proposes from the dissertation which it sees and are to the data transfer and the control also the connection directivity of the cluster group to improve also the lag time diminishes, test result it will lead and the possibility which it will know it was.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.4 no.4
• /
• pp.793-801
• /
• 2000

This paper presents the effect of lightning impulse current on ZnO varistors(390[V], 6.5[kA]) used in low-voltage AC mains as a protective device against transient overvoltages. The electrical characteristics of ZnO varistors are deteriorated by overtime impulse current, and a deteriorated ZnO varistor is brought to a thermal runaway and finally destroyed even in normal operating voltage. Therefore, it is important to estimate the changes of the electrical characteristics of ZnO varistors. A lightning impulse current standardized in IEC 61000-4-5 is applied to the varistors to accelerate deterioration, and the energy applied to the varistor at each time is about 12 [J]. In the experiment, various parameters such as leakage current, reference voltage are measured with the number of applied impulse current. Also, micro-structure changes of the varistors after applying the lightning impulse current of 200 times are compared. The electrical characteristics of the varistors are degraded by overtime impulse current, showing increase in leakage current and decrease in reference voltage.

• Journal of the Korean Vacuum Society
• /
• v.12 no.4
• /
• pp.275-280
• /
• 2003

Epitaxial Gd$_2O_3:Eu^{3+}$luminescent thin films have been grout on Si(III) substrates using ionized Cluster Beam Deposition (ICBD). After the film growing, they were implanted and post annealed to change the crystal structure. The initial growth stage was monitored by using in-situ Reflection High Energy Electron Diffraction (RHEED). The formed crystal structure was identified with X-ray diffraction (XRD) technique and Fourier transform infrared (FT-R) spectroscopy. The electronic states variations were investigated by Near Edge X-ray Absorption Fine Structure (NEXAFS). Photoluminescence (PL), Cathodoluminescence (CL). and Vacuum ultraviolet (VUV) spectrum were used for examining the optical properties. We report the optical property changes depending on crystal structure and the electronic states.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.231-231
• /
• 2013

ZnO은 hexagonal wurtzite 구조를 갖는 직접 천이형 화합물 반도체로서, 상온에서 3.37 eV 정도의 wide band gap energy를 가지고 있으며, 60 meV의 큰 엑시톤 결합 에너지(exciton binding energy)를 갖는다. 또한 동종 기판이 존재하고 열, 화학적으로 안정한 상태이며 습식 식각이 가능한 장점으로 인해 각광받고 있다. 또한, ZnO 박막은 우수한 전기 전도성을 나타내며 광학적 투명도가 우수하기 때문에 투명전극으로 많이 이용되어 왔고, 태양 전지(solar cell), 가스 센서, 압전소자 등 많은 분야에서 사용되고 있다. 이와 같은 ZnO박막을 안정적인 쇼트키 다이오드 특성을 얻기 위해서는 쇼트키 배리어 장벽의 형성이 필수적이다. Mg을 ZnO에 첨가하여 MgZnO 박막을 형성할 경우, 금속의 일함수와 MgZnO의 전자친화력 차이가 증가하여 더 큰 쇼트키 장벽 형성이 가능하며, 금속의 일함수가 큰 물질을 사용해야 한다. 또한, 박막의 결함이 적은 박막을 형성해야 하는 에피탁셜 박막이 필요하다. SiC는 높은 포화 전자 드리프트 속도(${\sim}2.7{\times}107$ cm/s), 높은 절연 파괴전압(~3 MV/cm)과 높은 열전도율(~5.0W/cm) 특징을 가지고 있으며, MgZnO/Al2O3의 격자 불일치는 ~19%인 반면에 MgZnO/SiC의 격자 불일치는 ~6%를 가진다. 금속의 일함수가 큰 Ag 금속은 열처리가 될 경우 AgOx가 될 경우 더욱 안정적인 쇼트키 장벽을 형성될 수 있을 것으로 판단된다. 본 연구에서는 쇼트키 접합을 형성하기 위해 금속의 일함수가 큰 Ag 금속을 사용하였으며, Al2O3 기판과 6H-SiC 기판위에 MgZnO(30 at.%) 박막을 증착하였다. 증착 후에 Ag를 증착 한 뒤 급속 열처리를 하였다. 열처리된 MgZnO의 경우 열처리 하지않은 소자보다 약 $10^5$ 이상의 우수한 on/off 특성을 보였다.

• Tunnel and Underground Space
• /
• v.20 no.6
• /
• pp.446-454
• /
• 2010

CAES-G/T (Compressed Air Energy Storage - Gas Turbine) power generation is a likely option for the buffer facility stabilizing the fluctuation of the renewable powers, such as wind and solar powers. Considering the geological conditions, the underground CAES facility is most probable if the CAES-G/T generation is planed in Korea. In this kind of facility, a concrete plug is installed to seal the compressed air in the container, so that the selection of the shape and dimension of concrete plug could be a critical design factor. The stability evaluation of two types of plug was carried out by investigating the distribution of the factor of safety in the plugs and the distribution of contact pressure over the contact surface. The analysis result shows that the taper-shaped plug is more structurally stable than the wedge-shaped plug for the given geological condition. Possible separation of the rock-concrete interface around the spring line of the wedge-shaped plug is anticipated, which means the possible leakage of compressed air through the side wall and also means the poor mobilization of frictional resistance on that area.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2011.11a
• /
• pp.31-31
• /
• 2011

섬유제품은 대부분은 흡수성 또는 흡유성을 가지고 있어 물이나 기름이 등을 쉽게 흡수하는 성질이 있다. 이러한 성질 때문에 물이나 기름 등의 접촉에 의한 얼룩과 오염이 잘 되는 단점을 가지고 있다. 이러한 문제점을 해소하기 위하여 원단에 대한 발수, 발유, 방오가공 등이 연구되어 왔으며 섬유의 고유한 화학적, 기계적 물성을 유지하면서 표면과 이면이 다른 특성을 가지도록 유도하여 기능성을 부여하는 편면가공을 주목을 받게 되었다. 본 연구에서는 불소계로 발수처리 된 PET직물에 저온 Plasma와 Sputter을 이용하여 직물의 한쪽 면에는 친수성과 다른 면에는 발수성이 동시에 나타나는 편발수에 관한 실험을 했다. 불소계로 발수처리 된 시료와 저온 Plasma처리된 시료와 Sputter처리된 시료(처리면, 미처리면)를 접촉각 5회 측정하여 평균값을 나타냈다. 발수처리 된 시료의 평균 접촉각 값은 $149^{\circ}$이며, 저온 Plasma의 평균값은 $45^{\circ}$(처리면) $128^{\circ}$(미처리면), Sputter는 $74^{\circ}$(처리면) $144^{\circ}$(미처리면) 으로 가공처리 된 시료에는 양면의 접촉각이 확연한 차이가 나타난 걸로 미루어 보아 편면발수효과가 얻어졌다고 판단된다. SEM 측정을 통하여 관찰한 경우, 발수처리 된 시료에서는 불소계 발수제의 흔적이 보였다. 저온 Plasma, Sputter 처리된 시료에서는 처리시간이 높아짐에 따라서 시료표면에 코팅된 불소계 발수제 막들이 점점 파괴되는 것을 관찰할 수 있었다. 그리고 건식가공으로 인하여 처리된 표면에는 Etching작용이 일어나 표면적이 넓어져 친수화가 일어난 것으로 생각된다. 이처럼 저온 Plasma가공과 Sputter가공으로 편발수를 얻을 수 있다면 에너지 절약, 처리공정과 시간단축 등 여러 가지 장점이 기대된다.

• Elastomers and Composites
• /
• v.33 no.4
• /
• pp.267-273
• /
• 1998

Isocyante terminated urethane prepolymers were synthesized by the reaction of 4,4'-dimethyl phenyldiisocyanate(MDI) and ester type polyols such as ethylene glycol/ butanediol adipate(EBA), neopentylglycol/butanediol adipate (NBA) and hexanediol adipate (HA) . All of the NCO-terminated urethane prepolymers are solid at room temperature, but they become mobile enough to be disposed onto a substrate upon heating about $80^{\circ}C$. Subsequently, they are solidified and cured through the reaction with moisture. Tensile behavior of the ore-thane hotmelt exhibits characteristic features depending on the type of polyol. The adhesive strength determined by single lap shear joint is higher in order of HA, NBA and EBA based ore thane hotmelt, which can be correlated with the magnitude of breaking energy of the cured films. The failure mode are cohesive for all cases and the adhesive strength increases as the test is performed faster. This indicates that the strength of the adhesive joint is primarily dependent upon the bulk properties of the adhesives.

• Cross-Cultural Studies
• /
• v.51
• /
• pp.45-71
• /
• 2018

This essay explores Louise Erdrich's politically resistant voice which interrogates and disrupts the long-lasting, pernicious misbelief about Native Americans as 'vanishing people'. This essay chiefly focuses on the two female characters-Lulu Nanapush and Marie Lazarre Kashpaw-in the author's widely acclaimed novel Love Medicine (1993). First, illustrating the Chippewas' multifaceted resistances against white Americans' colonialist dominance disclosed in their enforcement of governmental policy, law, religion, and culture, this essay investigates how Erdrich does not stop telling her story that the idea of 'vanishing people'-another version of 'Manifest Destiny'-is unfounded. Second, by referring to Freud's and Marcuse's speculation on 'Eros'-the great unifying energy that preserves all life-as an alternative to the predicament caused by an oppressive civilization, this essay illuminates Erdrich's vision of sustaining and regenerating the Chippewas' tribal life and heritage that center on the embracing power of love reified in Lulu and Marie. Their undying energy consolidating their communal love and ties, despite the destructive, oppressive colonialist milieu inflicted on the Chippewa Indian reservation, sheds light on the author's politics of 'Eros' predicated tightly upon her historical consciousness.

• Korean Journal of Materials Research
• /
• v.29 no.2
• /
• pp.73-78
• /
• 2019

Lead free $(Ba_{0.7}Ca_{0.3})TiO_3$ thick films with nano-sized grains are prepared using an aerosol deposition (AD) method at room temperature. The crystallinity of the AD thick films is enhanced by a post annealing process. Contrary to the sharp phase transition of bulk ceramics that has been reported, AD films show broad phase transition behaviors due to the nano-sized grains. The polarization-electric hysteresis loop of annealed AD film shows ferroelectric behaviors. With an increase in annealing temperature, the saturation polarization increases because of an increase in crystallinity. However, the remnant polarization and cohesive field are not affected by the annealing temperature. BCT AD thick films annealed at $700^{\circ}C/2h$ have an energy density of $1.84J/cm^3$ and a charge-discharge efficiency of 69.9 %, which is much higher than those of bulk ceramic with the same composition. The higher energy storage properties are likely due to the increase in the breakdown field from a large number of grain boundaries of nano-sized grains.