• Computational Structural Engineering
• /
• v.6 no.2
• /
• pp.95-102
• /
• 1993

A modeling method is described to provide a smaller structural dynamic model which can be used to compare finite element model of a structure with its experimental counterpart. A structural dynamic model is assumed to be represented by dynamic stiffness matrix. To validate a finite element model, it is often necessary to condense a large degrees of freedom (dofs) to a relatively small number of dofs. For these purpose, static reduction techniques are widely used. However, errors in these techniques are caused by neglecting frequency dependent terms in the functions relating slave dofs and master dofs. An alternative method is proposed in this paper in which the frequency dependent terms are considered by expressing the reduced dynamic stiffness matrix with orthogonal polynomials. The reduced model has finally a minimum set of dofs, such as sensors and excitation points and it is under the same condition as the physical system. It is proposed that the reduced model can be derived from finite element model. The procedure is applied to example structure and the results are discussed.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.35 no.4
• /
• pp.801-814
• /
• 2015

In this study, a statically simple indeterminate strut-tie model is proposed for the rational analysis and design of simply supported prestressed concrete beams by reflecting all characteristics of nonlinear structural behavior and load transfer mechanisms. In addition, a load distribution ratio that allows to transform the proposed indeterminate strut-tie model to a determinate model is also suggested to help structural designers conduct the structural analysis and design of simply supported prestressed concrete beams by using the strut-tie model method of current design codes. For verifying of the validity of the proposed model and load distribution ratio, the ultimate strengths of 47 simply supported prestressted concrete beams tested to failure were estimated and the results were compared with those by the strut-tie model methods of current design codes.

• Journal of the Korea Concrete Institute
• /
• v.19 no.5
• /
• pp.655-664
• /
• 2007

The inherent characteristic of concrete tensile cracks, directional nonlocal crack damage, causes so-called rotating tensile crack damage and softening of compressive strength. In the present study, a plasticity model was developed to describe the behavior of reinforced concrete planar members In tension-compression. To describe the effect of directional nonlocal crack damage, the concept of microplane model was combined with the plasticity model. Unlike existing models, in the proposed model, softening of compressive strength as well as the tensile crack damage were defined by the directional nonlocal crack damage. Once a tensile cracking occurs, the microplanes of concrete are affected by the nonlocal crack damage. In the microplanes, microscopic tension and compression failure surfaces are calculated. By integrating the microscopic failure surfaces, the macroscopic failure surface is calculated. The proposed model was implemented to finite element analysis, and it was verified by comparisons with the results of existing shear panel tests.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.27 no.5
• /
• pp.529-534
• /
• 2009

In this study, we investigate the feasibility of modeling entire image strips that has been acquired from the same orbital segments. We tested sensor models based on satellite orbit and attitude with different sets(Type1 ~ Type4) of unknowns. We checked the accuracy of orbit modeling by establishing sensor models of one scene using control points extracted from the scene and by applying the models to adjacent scenes within the same orbital segments. Results indicated that modeling of individual scenes with 1st or 2nd order unknowns was recommended. We tested the accuracy of around control points, digital map using the HIST-DPW (Hanjin Information Systems & Telecommunication Digital Photogrammetric Workstation) As a result, we showed that the orbit-based sensor model is a suitable sensor model for making 1/25,000 digital map.

• Journal of Aerospace System Engineering
• /
• v.15 no.1
• /
• pp.72-79
• /
• 2021

In this study, as part of the development of an autonomous flying personal aircraft, an equivalent model of the main wing assembly of an Optionally Piloted Personal Air Vehicle (OPPAV) was developed. Reliability of the developed equivalent model was verified by eigenvalue analysis. The main wing assembly consisted of a main wing, an inboard pod, and an outboard pod. First, for developing an equivalent model of each component, components to produce the equivalent model were divided into several sections. Nodes were then created on the axis of the equivalent model at both ends of each section. In addition, static analysis with unit force and unit moment was performed to calculate the deformation or the amount of rotation at the node to be used in the equivalent model. Equivalent axial, bending, and torsional stiffness of each section were calculated by applying the beam theory. Once the equivalent stiffness of each section was calculated, information of a mass and moment of inertia for each section was entered by creating a lumped mass in the center of each section. An equivalent model was developed using beam element. Finally, the reliability of the developed equivalent model was verified by comparison with results of mode analysis of the fine model.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.29 no.7
• /
• pp.828-835
• /
• 2023

Vessel traffic service operators (VTSOs) need to quickly and accurately analyze the maritime traffic situation in the vessel traffic service (VTS) area and provide information to the vessels. However, if traf ic increases rapidly, the workload of VTSOs increases, and they may not be able to provide adequate information. Therefore, it is essential to develop VTSO support technologies that can reduce their workload and provide consistent information. In this paper, we propose a model for automatically detecting abnormal vessels in the VTS area. The proposed model consists of a positional model and a contextual model and is specifically optimized for the traffic characteristics of the target area. The implemented model was tested by using real-world data collected at a test center (Daesan Port VTS). Our experiments confirmed that the model could automatically detect various abnormal situations, and the results were validated through expert evaluation.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.49 no.4
• /
• pp.273-279
• /
• 2021

Winglets are specialized wingtip devices to reduce induced drag, and they have been installed on Boeing-made aircraft since the 1980s, Airbus has also developed a winglet named 'Sharklet' since 2009 and has started providing them as an option to the A320 Family. The winglet has the effect of improving take-off performance, reducing fuel consumption, increasing payload, and increasing flight distance by reducing the induced drag generated at the tip of the wing. The purpose of this study is to analyze the actual flight data of the sharklet-installed and non-sharklet-installed models of the A321 aircraft to verify the fuel efficiency improvement due to the winglet installation, and to analyze the economic analysis accordingly. Through this, it can be used to determine the winglet installation when introducing an aircraft or to make a decision for upgrading the existing aircraft. To this end, a case study on the aerodynamic characteristics and effects of the winglet installation was conducted, and the economic analysis was verified.

• Asia Marketing Journal
• /
• v.9 no.2
• /
• pp.49-95
• /
• 2007

The "cause-related marketing (CRM)," generally defined as a mutually beneficial relationship between a company and a non-profit relationship or a social cause, which is perhaps the most progressive outgrowth of marketing trend. This paper contributes to, and looks at the practical issues of CRM and its effect on the brand attitude of the customer. To do so, following three broad research questions have been addressed. Which cause-related orientation is effective on customer's attitude of the brand? Which type of cause-related message provides crucial impact on customer's attitude of the brand? How product category acts upon and brings about different consequences on CRM? To address these questions, a causal model has been developed incorporating message type, product relevance, social significance, and brand attitude. The study model was tested with survey data collected from 400 career professionals and students in Seoul and statistically processed the 176 valid ones. The results of the study considerably supported the conceptual model. The analysis also revealed that the study population was not able to detect the differences in CRM strategies but tend to conceptualize them as a whole.

• 한국전산유체공학회:학술대회논문집
• /
• 1995.10a
• /
• pp.31-36
• /
• 1995

비유선형의 물체 주위의 유동은 정체유동, 경계층 박리 및 주기적 와열 생성 등의 복잡한 유동현상이 공존한다. 본 연구에서는 비교적 단순한 형상인 정사각주 주위의 비정상 난류 유동을 2-방정식 와점성 난류모델인 표준 $k-{\varepsilon}$ 모델과 RNG $k-{\varepsilon}$ 모델을 이용하여 예측할 수 있는지를 검증하였다. 정교하게 수행된 최근의 실험과 대와류모사(LES)의 결과를 검증을 위한 비교의 자료로 삼았다. 적절한 난류모델의 선정과 더불어 시간 정확도, 공간 정확도 및 대류항 처리법 등이 해석결과에 미치는 영향도 살펴보았다. 기존의 표준 $k-{\varepsilon}$모델은 정체점 부근에서 난류 운동에너지를 과도하게 생성하는 근본적인 문제점 때문에 실험 및 LES의 결과를 제대로 예측할 수 없었다. 난류운동에너지의 초과 예측에 따른 운동량의 과도한 혼합으로 인해, 항력계수 및 양력계수의 비정상성 뿐 아니라 평균 항력계수도 부정확하게 예측하였다. RNG $k-{\varepsilon}$ 모델을 사용한 경우에는 정체점 주위 유동현상의 예측이 상당히 향상되어 항력계수 및 양력계수의 평균치, 진폭 및 비정상성의 주기 등을 정확하게 예측하는 것이 가능하였다. 그러나 이 경우에도 예측의 정확도가 시간 증분과 격자의 크기 및 대류항 처리법등에 영향을 받으며, 특별히 대류항 처리법에 상당히 민감하게 변하는 것을 알 수 있었다. 향상된 유동예측은 RNG $k-{\varepsilon}$ 모델의 난류에너지 소산율 방정식의 개선된 항이 과도하게 생성된 난류에너지를 정체점 부근에서 제거하기 때문에 가능하다는 것을 알 수 있었다.의 20세 이하 골절 및 탈구가$30.3\%까지 감소하게되어 년도가 증가함에 따라 청장년 층에 비하여 소아골절 및 탈구가 전체적으로 감소하는 경향을 보였다. 스키골절의 부위별 발생빈도는 1990년 이전까지 하지골절 및 탈구가 많았으나 이후 점차 상지의 골절 탈구가 증가하였다 하지에서 가장 많은 골절은 경골 골절이었으며, 경골골절은 회전력에 의한 나선형골절이 $76.5\%로 가장 많았고 년도에 따른 변화는 보이지 않았다. 스키손상의 발생빈도는 초기에 비하여 점차 감소하는 경향을 보였으며, 손상의 특성도 부위별, 연령별로 다양한 변화를 나타내었다.해가능성을 가진 균이 상당수 검출되므로 원료의 수송, 김치의 제조 및 유통과정에서 병원균에 대한 오염방지에 유의하여야 할 것이다. 확인할 수 있었다. 이상의 결과에 의하면 고농도의 유기물이 함유된 음식물쓰레기는 Hybrid Anaerobic Reactor (HAR)를 이용하여 HRT 30일 정도에서 충분히 직접 혐기성처리가 가능하며, 이때 발생된 $CH_{4}$를 회수하여 이용하면 대체에너지원으로 활용 가치가 높은 것으로 판단된다./207), $99.2\%$(238/240), $98.5\%$(133/135) 및 $100\%$ (313)였다. 각각 두 개의 요골동맥과 우내흉동맥에서 부분협착이나 경쟁혈류가 관찰되었다. 결론: 동맥 도관만을 이용한 Off pump CABG를 시행하여 감염의 위험성을 증가시키지 않으면서 영구적인 신경학적 합병증을 일으키지 않았고 좋은 혈관 개존율을 보여주었다. 따라서 동맥 도관을 이용한 Off pump CABG는 관상동맥의 협착의 정도에 따라 효율적으로 시행

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.4A
• /
• pp.304-311
• /
• 2005

OCSP has specific characters which can suspend, close, and correct in real time. But, as more clients use the OCSP server verification, more updated information is needed, which can lead to jamming in the OCSP server. To apply this technique of Distributed OCSP server so as to reduce the certificate verification OCSP from jamming. Also, the Distributed OCSP server will solve the problems of the intensive central structure. Simulation results show that the average reply time of certificate verification request and server load are reduced in the case using distributed OCSP. In addition to this advantage, resource distribution and fault tolerance are acquired because of multiple OCSP.