• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.3
• /
• pp.195-202
• /
• 2004

This paper presents a current control strategy to reduce torque ripple of Brushless DC Motor during con)mutation. The torque ripple is mainly caused by the inequality in the rate of change between rising current and decaying one during commutation. And also it is influenced by the shape of real back EMF Therefore, in the proposed control strategy, considering real back EMF a compensation voltage is generated to equalize the rate of change in these commutating currents. And then, by providing the compensation voltage during commutation, the torque ripple can be reduced. The simulation md experimental results verify that the proposed method can reduce the torque and the current ripples significantly.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.969-970
• /
• 2011

본 논문은 표면부착형 영구자석 동기전동기(Surfacemounted Permanent Magnet Synchronous Motor)의 영구자석 offset의 변화와 노치(notch)의 적용에 따른 코깅토크 저감 특성을 분석하고, 중심합성계획법(Central Composite Design)을 이용한 최적 모델 설계에 대한 연구이다. 영구자석 offset만 적용한 모델의 경우 코깅토크의 피크-피크값은 95%로 크게 저감되었지만 정격전류 인가시 평균토크의 감소율이 12.3%로 출력 손실이 크기 때문에 최적 설계를 통해 추가적으로 노치를 적용하고 영구자석 Offset을 조절함으로써 코깅토크 저감율을 96.5%로 개선시킬 수 있었고, 평균토크의 감소율은 7.7%로 영구자석 offset만 적용한 모델보다 평균토크의 감소량이 작아진 것을 확인할 수 있었다.

• Journal of Power System Engineering
• /
• v.12 no.5
• /
• pp.20-26
• /
• 2008

양산되는 승용차용 토크 컨버터 내부의 유동을 LDV 측정 기술을 이용하여 정량화했다. 속도비 0.4와 0.8 경우에 대한 속도 측정을 통해 임펠러 유로 중간과 출구 영역의 질량 유동율 특성을 분석했다. 측정 단면의 속도 분포는 유로의 위치와 속도비에 따라 많은 차이를 보이며, 특히 속도비 0.8 조건에서 임펠러 유로 중간영역 흡입면 부근의 유동은 유동박리에 의한 재순환 현상을 나타내며, 이와는 대조적으로 출구 영역에서는 흡입면을 따라 역류 현상이 발생한다. 임펠러 유로 내부의 유동은 각 영역에서 속도비에 따라 개별적 유동 특성을 보인다. 질량 유동율은 모든 속도비와 측정단면에서 주기적인 변화를 보이며, 또한 터빈의 순간적인 위치가 임펠러 유로 측정단면의 질랑 유동율에 매우 큰 영향을 미치는 것이 밝혀졌다 따라서 토크 컨버터 임펠러의 유로 방향 유동 특성 변화는 컨버터 설계에 중요하게 고려되어야 할 것으로 보인다.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.28 no.1
• /
• pp.27-36
• /
• 2012

As the popularity of implant treatment using a variety of problems have been reported. The proper torque values recommended by the manufacturer and the actual tightening force applied to the observed differences. Period for each product used in this study using different torque controllers accuracy for each of the comparisons, were analyzed. Error rate varies by the manufacturer, but all the products used in the reference period for increasing the error rate increased. Repeat the initial tightening, but the reference, showed a value close to the reference value for the width of change was larger. However, increasing the number of repeated tightening of the reference value for the error rate increased, but has reduced the width of the observed changes.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.3
• /
• pp.231-237
• /
• 2007

The torque ripple of the hydraulic pumps for the Electro-hydrostatic Actuators can disturb the cylinder position control under slewing speed operation condition. In principle, the periodic change of the reaction torque generated by a piston type pump is highly dependent on the waveform of its cylinder chamber pressure. In case of uni-directional pumps operating at constant speed, the transient overshoot and rising slope of the cylinder pressure can be adjusted by the precompression angle and notch shape of their valve plates. Therefore, the influence of the valve plate geometry on the torque ripple magnitude of a bent-axis type piston pump for EHA application was investigated in this study. The results showed that any improvement of the torque ripple of such a bi-directional pump can not be achieved by modifying the valve plate geometry, regardless of its operation speed.

• Journal of the KSME
• /
• v.31 no.1
• /
• pp.51-59
• /
• 1991

본 글에서는 일반적인 공간 매니퓰레이터에 관한 가속도 이론을 서술하였다. 즉, 주어진 매 니퓰레이터에 대하여 액튜에이텨 토크집합 T에 대한 치역 $S_t$와 관절변수변화율집합 F에 대한 지역 $S_q$를 정의하였다. 또한 상태공간에서의 한 점 u에서의 상태가속도 집합 $S_u$를 정의하였다. 치역 $S_t$를 결정하고 그 성질인 최대가속도와 동방가속도를 결정하였다. 아울러, 가속도이론의 하나의 적용례로서 정해진 동방기동가속도를 얻을 수 있는 최소한의 액튜에이터 토크의 크기를 결정하는 방법을 도시하였다. 본 결과의 다양한 응용예는 기존연구를 참조하기 바란다.

• Journal of the Korean Society of Safety
• /
• v.12 no.4
• /
• pp.214-219
• /
• 1997

The mechanical seals, which are installed in rotating machines like pump and compressor, are generally used as sealing devices in the many fields of industries. The failure of mechanical seals such as leakage, crack, breakage, fast and severe wear, excessive torque, and squeaking results in big problems. To identify abnormal phenomena on mechanical seals and to propose the proper monitoring parameter for the failure of mechanical seals, sliding wear experiments were conducted. Acoustic emission, torque, and temperature were measured during experiments. Optical microstructure was observed for the wear processing after every 10 minute sliding at rotation speed of 1750 rpm and scanning electron microscopy was also observed. Except for the initial part of every experiment, the variation of acoustic emission was well coincided with torque variation during the experiments. This study concludes that acoustic emission and torque are proper monitoring parameters for the failure of mechanical seals. The intensity of acoustic emission signals is measured in root mean square voltage. Temperature of sealing face will be used as a parallel parameter for increasing the reliability of monitoring system.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.17 no.1
• /
• pp.83-88
• /
• 2011

There are various environmental conditions under which ship may navigate over ocean or in harbor. Ship's torque and speed change frequently under the voyage conditions. In this case, harmonics is created in the electrical power systems. The major adverse impacts of voltage and current harmonics in the electrical power systems on generator, transformer, converter, inverter and propulsion motor lead to the increase of machine heating caused by iron and copper losses which are dependent on frequency. In this paper, an analysis of THD(total harmonic distortion) for currents and voltages in the propulsion equipment was carried out. The THD and torque ripple in the input currents of the propulsion motor have been confirmed by the simulation results.

• Polymer(Korea)
• /
• v.35 no.4
• /
• pp.342-349
• /
• 2011

The effect of the amount of vinyltriethoxysilane (VTEOS) in precipitated silica filled silicone rubbers was extensively investigated in terms of the change of mechanical properties, heat resistance, oil resistance, compression set, resilience, and curing characteristics. As the content of VTEOS increased from 0 to 2.0 phr, the hardness of the silicone rubber increased, however, tensile strength, elongation at break, and tear strength decreased. From heat resistance test, the change of mechanical properties was pronounced for silicone rubber treated with more VTOES. The best heat resistance was achieved at 2.0 phr VTOES. In addition, oil resistance was proportionally improved with VTEOS content. From oil resistance test. it was found that the decrease in hardness and maximum elongation was reduced for VTEOS-added systems. Finally, resilience, compression set, degree of cure and crosslink density were significantly enhanced with the amount of VTEOS.

• Korean Journal of Agricultural Science
• /
• v.17 no.1
• /
• pp.45-51
• /
• 1990

This study was conducted to obtain basic data for the design of cooling system by the test of engine performance of the power tiller being used widely in the rural area. Among the various factors affecting engine performance, the flow rate of cooling water was considered as the major factor in this study. Motoring loss, output, fuel consumption ratio, torque, heat absorption of cooling water, and thermal efficiency were measured and analyzed based on three flow rates of cooling water such as 15, 20, and $25{\ell}/min$. The results obtained were as follows : 1. Motoring loss of the engine was 1.371 kW at 2,200 rpm., and mechanical efficiency was 79.1% at rated output level. 2. Output power of the engine increased with the flow rate of cooling water increased. 3. BSFC was 282.9g/kW-h at the flow rate of $20{\ell}/min$, and the temperature of cooling water at outlet was $80.9^{\circ}C$. 4. There was a little variation of torque of the engine depending on the flow rate of cooling water. 5. Absorption of heat by cooling water was increased with the increase of flow rate. 6. The highest thermal efficiency of 32.3% at the flow rate of $20{\ell}/min$ was observed.