• 한국신재생에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.63.1-63.1
• /
• 2011

To analyze the phenomenon of corrosion in the PV module, we experimented damp heat test at $85^{\circ}C$/85% relative humidity(RH) and $65^{\circ}C$/85% RH for 2,000 hours, respectively. We used 30 mini-modules designed of 6inch one cell. Despite of 2,000 hours test, measured $P_{max}$ is not reached failure which is defined less than 80% compared to initial $P_{max}$. Therefore, we calculate proper curve fitting over 2,000 hours. Data less than 80% $P_{max}$ is found and B10 lifetime is calculated by the number of failure specimens and weibull distribution. Using B10 lifetime that the point of failure rate 10% and Peck's model, the predictable equation of lifetime was derived under temperature and humidity condition.

• Journal of the Korean Solar Energy Society
• /
• v.36 no.2
• /
• pp.65-72
• /
• 2016

PV module is installed in various outdoor conditions such as solar irradiation, ambient temperature, wind speed and etc. Increase in solar cell temperature within PV module aggravates the behaviour and durability of PV module. It is difficult to measure temperature among respective PV module components during PV module operating, because the temperature within PV module depends on thermal characteristics of PV module components materials as well as operating conditions such as irradiation, outdoor temperature, wind etc. In this paper, simulation by using finite element method is conducted to predict the temperature of each components within PV module installed to outdoor circumstance. PV module structure based on conventional crystalline Si module is designed and the measured values of thickness and thermal parameters of component materials are used. The validation of simulation model is confirmed by comparing the calculated results with the measured temperatures data of PV module. The simulation model is also applied to estimate the thermal radiation of PV module by front glass and back sheet.

• 한국태양에너지학회:학술대회논문집
• /
• 2012.03a
• /
• pp.457-462
• /
• 2012

Daylighting software is an important component to predict the performance of daylighting system in advance of a field demonstration study with installing them in buildings. PHOTOPIA is a powerful software to generate a candela distribution curve(CDC) of an active daylighting system like a tracking dish concentrator. With PHOTOPIA, a set of candela distribution curves was generated under clear sky conditions and different solar altitude angles. The candela distribution curves were then imported to RADIANCE for rendering and analysis on the daylighting performance of a tracking dish concentrator when it installed in a actual class room without windows. As a result, the daylight collection efficiency of the dish concentrator was 68.4% when we assumed that there was no tracking error. It was found that candela(cd) and total lumens(lm) increased with solar altitude rising, whereas the distribution angle was fixed. The illuminance uniformity on the work plane in the class room was relatively low, 0.12, while the illuminance uniformity on the area of $2.7m^2$ to which the light was illuminated was considerably high, 0.60. The maximum illuminance was 1,340lux with a solar altitude angle of 80 degrees.

• Journal of the Korean Solar Energy Society
• /
• v.32 no.3
• /
• pp.104-113
• /
• 2012

A set of candela distribution curves(CDCs) were generated for a fiber optic dish daylighting system by Photopia under clear sky conditions at different solar altitudes. The candela distribution curves were then exported to Radiance for photometric analysis of a windowless lecture room. Observations were made on the Radiance rendered illuminance images, which provided photo realistic scenes varying with solar altitudes. If no tracking error were assumed, the daylight collection efficiency of the system remained at a constant value of 68.4% during its operation. Higher the solar altitude angle, greater in photometric quantities were observed, which are represented by candela(cd) and total lumens(lm). In all cases considered, however, the angle of light distribution remained fixed reflecting the solar tracking feature of the system. The illuminance uniformity on the workplane lingered around 0.12, which is quite low. This is quite a contrast to its average value of 0.68 of the $2.7m^2$ area directly below the terminal device (diffuser) of the system. The maximum illuminance of 1,340lux was obtained at a solar altitude of 80 degrees.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.79-79
• /
• 2010

다른 물질에 비해 많은 우수한 특성을 가지고 있는 CuInSe2(CIS)박막 태양전지는 많은 연구자들에 의해 개발되어 오고 있다. CIS의 대표적인 장점으로는 직접천이형 밴드갭, 높은 흡수계수, 열 안정화상태 및 p형으로의 전도성물질의 가능성 등 다양하다. 또한 간단한 구조를 이용하여 유리같은 싼 기판을 이용하기 때문에 저가형 태양전지로서 많은 각광을 받고 있다. CIGS태양전지는 CIS의 In 사이트에 Ga을 도핑함으로서 만들어지는데 밴드갭은 약 1.4eV이다. CIS박막을 만드는 많은 방법이 존재하나 구성원소로부터 최적화된 조성을 찾을수 있는 방법이 가장 중요한 요소 중의 하나로 인식되고 있으며, 이런점에서 증발법 및 스퍼터링법 등 같은 진공방식이 비진공방식에 비해 훨씬 간편하게 조성비를 맞출수 있다. 그 중에 스퍼터링법은 대면적 박막태양전지로의 가능성으로 비출어 볼때 산업화를 위한 좋은 후보군이 될 수 있다. Selenization을 하기전에 Cu-In-Se의 전구체 조합은 여러개의 타겟으로부터 동시 스퍼터링법이나 다층 전구체법을 사용하여 준비되는데 어떤 방법이 되던지 Se의 부가적인 공급은 불가피하다. 지금까지 많은 관련 연구의 대부분인 구조적, 조성비적 그리고 광학적인 특성평가에 집중되어 오고 있는데, 전기적특성평가의 경우는 면저항, 비저항 같은 간단한 결과 위주로 보고되어 오고 있다. 또한 캐리어농도와 이동도에 대한 보고가 있음에도 불구하고 이해되기에는 충분치 못한 면이 많다.본 발표에서는 태양전지 제조 전단계로서 소다라임유리기판(SLG)위에 Mo의 유무에 따라 CIS박막의 전기적인 특성 변화에 대한 내용을 담고 있다. 소다라임유리($2cm{\times}2cm$)를 기판으로 사용하여 아세톤-에탄올 용액에 초음파세척을 수행하고, Mo 후면전극을 DC 스퍼터링방식을 이용하여 증착을 한다. SLG와 Mo이 코팅된 SLG를 각각 RF 스퍼터 챔버에 이송한 후 수증기 제거를 위해 약 10분간 예열을 한다. 샘플에 대한 전기적특성은 Hall효과 측정장치에 의해 측정이 되며 전기전도도, 캐리어농도, 이동도 및 전도형에 대한 정보가 각각의 변수에 따라 조사된돠. 부가적으로 구조적, 조성비적인 특성을 SEM,XRD 및 EDX를 통해 조사를 하여 전기적 특성에 따른 관계성을 검토한다. SLG와 Mo가 코팅된 SLG위의 CIS박막은 전기적으로 약간 다른 특성을 보일 것으로 예측되며, 이러한 기대를 바탕으로 조성비가 이상적인 화학양론에 근접할 때 p형으로서 제시될 수 있다는 것을 보여줄 것이다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.816-819
• /
• 2007

국내에서 IGCC 플랜트의 복합발전시스템의 평가는 여러 분야별로 진행되어 왔다. 크게 살펴보면 다음과 같다. 첫 번째는 가스터빈 쪽의 기술이다. 즉, 기존 천연가스를 이용하는 가스터빈을 어떻게 하면 석탄가스를 사용하는 IGCC 플랜트에 적합하게 맞출 것인가 하는 문제이다. 두 번째는 효율을 어떻게 하면 높일 수 있는가의 문제로서 석탄의 종류, 가스화 방법을 효율적으로 선택, HRSG(heat recovery steam generator)를 효율적으로 설계, 그리고 정제공정에서의 에너지 소비를 줄이는 분야였다. 세 번째는 어떻게 하면 오염을 줄일까의 문제로서 질소나 스팀 분사를 연계하여 NOx를 감소시키고 정제 공정에 사용되는 촉매를 개발한다던지 공정을 발달시키는 분야였다. 이 외에도 여러 종류의 연구가 이 분야에서 있었으나 주로 설계 분야의 연구가 주되였다. 이것은 발전소의 건설을 위한 초기 단계로서 당연한 결과일 수 있다. 그러나, 지금 IGCC 플랜트가 건설되는 과정에 있으므로 우리나라 전력계통 연계와의 문제도 생각해보아야 한다고 생각한다. 따라서 이번 연구에서는 IGCC 플랜트 운영의 불확실성이 약간이라도 존재하기에 이 플랜트가 기저발전 보다는 첨두발전 쪽이나 태양열/광발전, 풍력발전 등 다른 신재생에너지 자원처럼 독립된 전력 시스템으로 운영될 것이라 생각하고 이렇게 운영될 때는 발전소의 부하률의 변화가 심할 수 있다는 가정하에 플랜트의 부하률에 따른 석탄의 합성가스, 연료가스 전환량 및 전환효율 및 발전량 및 발전효율을 전산모사를 통해 예측해보았다.

• Journal of the Korean Solar Energy Society
• /
• v.27 no.3
• /
• pp.117-125
• /
• 2007

This study proposes a CFD(Computational Fluid Dynamics) analysis as a method of verification of the designed-data and a supplement of the insufficient experiences in geothermal system, which shows a rapid growth among the renewable energies. The followings are the results. FLUENT 6.2.12 is used as a CFD tool on this study, with the equations of continuity, motion, energy for unsteady flow through pipes and k-epsilon turbulent model. S-type model which has one borehole with diameter 12m by depth 206m and T-type model which has 3 boreholes with $12m{\times}20m{\times}206m$ are proposed, and also the boundary conditions are described. The temperature differences between temperatures by CFD analysis and by on-site measurement are less than 1.5%, this shows a high reliability of CFD analysis process which this study proposes. After 11 days simulation operated 12 hours interval On/Off mode, it is clearly predicted that the outlet temperatures of geothermal pipes are increased by $1.2^{\circ}C$, and $2.2^{\circ}C$ after 4 months. And the outlet temperatures of geothermal pipes increased with increase of the mass flow rates through the pipes. T-type model shows that the 4m distance between boreholes are reasonable because the temperatures at 2m and 6m from boreholes are nearly same.

• Journal of the Korean Solar Energy Society
• /
• v.32 no.3
• /
• pp.138-145
• /
• 2012

Because of the climate changes and the development of building technologies, the cooling loads have been increased. Among the various renewable energies, geothermal energy is known as very useful and stable energy for heating and cooling of building. This study proposes a road snow-melting system of which heat is supplied from GSHP(Ground source heat pump) in viewpoint of the initial investment and annual running performance, which is also operating as a main facility of heating and cooling for common spaces. The results of this study is as followings. From the site measurement, it is found out that the road surface temperature above the geothermal heating pipe rose up to $5^{\circ}C$, which is the design temperature of road snow-melting, after 2 hours' operation and average COP(Coefficient of performance) was estimated as 3.5. The reliability of CFD has confirmed, because the temperature difference between results of CFD analysis and site measurement is only ${\pm}0.4^{\circ}C$ and the trend of temperature variation is quite similar. CFD analysis on the effect of pavement materials clearly show that more than 2 hours is needed for snow-melting, if the road is paved by ascon or concrete. But the road paved by brick is not reached to $5^{\circ}C$ at all. To evaluate the feasibility of snow-melting system operated by a geothermal circulation which has not GSHP, the surface temperature of concrete-paved road rise up to $0^{\circ}C$ after 2 hour and 40 minutes, and it does never increase to $5^{\circ}C$. And the roads paved by ascon and brick is maintained as below $0^{\circ}C$ after 12 hours geothermal circulation.

• Journal of the Korean Solar Energy Society
• /
• v.32 no.3
• /
• pp.33-41
• /
• 2012

As the wind farms in large scale demand enormous amount of construction cost, minimizing the economic burden is essential and also it is very important to measure the wind resources and forecast annual energy production correctly to judge the economic feasibility of the proposed site by way of installing a Met mast at or nearby the site. Wind resources were measured by installing a 80[m] high Met mast at WangdeungYeo Island to conduct the research incorporated in this paper and offshore wind farm was designed using WindPRO. Wind farm of 100[MW] was designed making use of 3 and 4.5[MW] wind generator at the place selected to compare their annual energy production and capacity factor applying the loss factor of 10[%] and 20[%] respectively to each farm. As a result, 336,599[MWh] was generated by applying 3[MW] wind generator while 358,565 [MWh] was produced by 4.5[MW] wind generator. Difference in the energy production by 3[MW] generator was 33,660 [MWh] according to the loss factor with the difference in its capacity factor by 3.8[%]. On the other hand, 23 units of 4.5 [MW] wind generators showed the difference of annual energy production by 35,857 [MWh] with 4.0[%] capacity factor difference.

• Journal of the Korean Solar Energy Society
• /
• v.31 no.5
• /
• pp.1-8
• /
• 2011

In this study, we performed a sensitivity analysis to see how the true north error of a wind direction vane installed to a meteorological mast affects predictions of the annual-average wind speed and the annual energy production. For this study, two meteorological masts were installed with a distance of about 4km on the ridge in complex terrain and the wind speed and direction were measured for one year. Cross predictions of the wind speed and the AEP of a virtual wind turbine for two sites in complex terrain were performed by changing the wind direction from $-45^{\circ}$ to $45^{\circ}$with an interval of $5^{\circ}$. A commercial wind resource prediction program, WindPRO, was used for the study. It was found that the prediction errors in the AEP caused by the wind direction errors occurred up to more than 20% depending on the orography and the main wind direction at that site.