• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.228-228
• /
• 2010

pin-형 비정질 실리콘 태양전지에서 p-층은 창물질로서 전기 전도도가 크고, 빛 흡수가 작어야 한다. p층의 두께가 얇으면 i층에서 충분한 내부전위를 얻을 수 없어 개방전압이 작아진다. 반대로 p-층 두께가 두꺼워지면 p-층 자체에서 빛 흡수가 증가하고, 높은 불순물 농도(> $10^{20}/cm^3$)에 의한 표면재결합이 문제가 되어 변환효율이 감소한다. 밴드갭이 큰 물질로 창층을 만들면 짧은 파장의 입사광이 직접 i-층을 비추므로 단락전류와 곡선인자를 증가시킬 수 있다. 본 실험에서는 비정질 실리콘 증착과 박막 특성 분석을 위하여, $5cm{\times}5cm$ 크기의 eagle 2000 glass(유리)와 p형 실리콘 wafer가 사용되었다. 투과도, 흡수도, Raman, 암전도도 와 광전도도 특성 측정에 유리 기판에 증착된 박막을, 두께 측정, FTIR 측정에는 실리콘 기판에 증착된 박막이 각각 사용되었다. p형 비정질 실리콘 증착에는 $SiH_4$, $H_2$, $B_2H_6$ 가스를 사용하였고, 플라즈마 형성에는 13.56MHz의 RF 소스가 사용하였다.p층은 $SiH_4$ 가스와 $H_2$ 가스비가 1:5인 조건에서 $B_2H_6$을 도핑하여 형성하였다. $B_2H_6$가스량을 변화시키며 형성하였으며, $B_2H_6$가스량이 증가함에 따라 암전도도가 증가하였으나, 광학적 밴드갭이 감소하였다. $H_2/SiH_4$ 가스 비가 0.001일 때 밴드갭은 1.76으로 i층보다 높게 형성되었으며, 암전도도는 $10^{-7}$이었다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.265-265
• /
• 2014

일반적으로 태양전지 및 반도체 공정에서 불순물 주입 과정인 도핑(Doping)공정은 크게 몇 가지 방법으로 구분해 볼 수 있다. 소성로(Furnace)를 이용하여 열을 통해 불순물을 웨이퍼 내부로 확산시키는 열확산 방법과 진공 챔버 내부에서 전자기장을 걸어 이온을 극도로 가속시켜 진행하는 이온 주입(Ion implantation)이나 이온 샤워(Ion shower)를 이용한 도핑 방법이 있다. 또한 최근 자외영역 파장의 레이저광을 조사하여 광화학 반응에 의해 도펀트 물질를 분해하는 동시에 조사 부분을 용해하여 불순물을 도포하는 기법인 레이져 도핑(Laser doping) 방법이 개발중이다. 그러나 레이져나 이온 도핑 공정기술은 고가의 복잡한 장비가 필요하여 매출 수익성 및 대량생산에 비효율적이며 이온 주입에 의한 박막의 손상을 치료하기 위한 후속 어닐링(Post-annealing) 과정이 요구되는 단점을 가지고 있고 열확산 도핑 방법은 정량적인 불순물 주입 제어가 어렵고 시간 대비 생산량의 한계가 있다. 반면 대기압 플라즈마로 도핑을 할 경우 기존에 진공개념을 벗어나 공정상에서 보다 저가의 생산을 가능케 할 뿐아니라 멀티 플라즈마 소스 개발로 이어진다면 시간적인 측면에서도 단연 단축시킬 수가 있어 보다 대량 생산 공정에 효과적이다. 따라서 본 연구에서는 새로운 도핑 방법인 대기압 플라즈마를 이용한 도핑 공정기술의 가능성을 제안하고자 도핑 공정 시 웨이퍼 내 전류 패스(Current path)에 대한 메카니즘을 연구하였다. 대기압 플라즈마 방전 시 전류가 웨이퍼 내부에 흐를 때 발생되는 열을 이용하여 도핑이 되는 형식이란 점을 가정하고 이 점에 대한 원리를 증명하고자 실험을 진행하였다. 실험 방식은 그라운드(Ground) 내 웨이퍼의 위치와 웨이퍼 내 방전 위치에 따라 적외선 화상(IR image: Infrared image) 화상을 서로 비교하였다. 적외선 화상은 실험 조건에 따라 화상 내 고온의 표식이 상이하게 변하는 경향성을 나타내었다. 이 고온의 표식이 전류 패스라는 점을 증명하고자 시뮬레이션을 통해 자기장의 전산모사를 한 결과 전류 패스의 수직 방향으로 자기장이 형성이 됨을 확인하였으며 이는 즉 웨이퍼 내부 전류 패스에 따라 도핑이 된다는 사실을 명백히 말해주는 것이며 전류 패스 제어의 가능성과 이에 따라 SE(Selective Emitter) 공정 분야 응용 가능성을 보여준다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.4
• /
• pp.333-339
• /
• 2011

In this work, electrochemical characteristics and optical transmittance of carbon nanotubes (CNTs) counter electrodes which had different amount of CNTs in CNTs slurries were analyzed. Two-step heat treatment processes were applied to achieve well-fabricated CNTs electrode. Three sets of CNTs electrodes and dye-sensitized solar cells (DSSCs) with CNTs counter electrodes were prepared. As the amount of CNTs increased, sheet resistance of CNTs electrode decreased. CNTs electrode with low sheet resistance had low electrochemical impedance and fast redox reaction. On the other hand, in case of CNTs counter electrode with low density of CNTs, performance of the dye-sensitized solar cell was improved due to its high optical transmittance. We found that the transmittance of CNTs counter electrode influence the performance of dye-sensitized solar cells.

• KEPCO Journal on Electric Power and Energy
• /
• v.2 no.1
• /
• pp.49-54
• /
• 2016

The large scaled lead-acid battery is widely used for efficient operation of the photovoltaic system in many islands. However, lithium-ion battery is now being introduced to mitigate the fluctuation of wind power and to replace lead-acid battery. Therefore, hybrid ESS (Energy Storage system) that combines lithium-ion battery with lead-acid battery is being required because lithium-ion battery is costly in present stage. Under this circumstance, this paper presents the optimal algorithm to create composition rate of hybrid ESS by considering fixed and variable costs in order to maximize advantage of each battery. With minimization of total cost including fixed and variable costs, the optimal composition rate can be calculated based on the various scenarios such as load variation, life cycle and cost trend. From simulation results, it is confirmed that the proposed algorithms are an effective tool to produce a optimal composition rate.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.5
• /
• pp.3391-3398
• /
• 2015

Recently, the large scaled lead-acid battery is widely introduced to efficient operation of the photovoltaic system in many islands. but the demand of lithium-ion battery is getting increased by the operation of wind power and replacement of the lead-acid battery. And also, under the renewable portfolio standard(RPS) and energy efficiency resource standard(EERS) policy of Korea government, the introduction of energy storage system(ESS) has been actively increased. Therefore, this paper presents the operation algorithm of hybrid battery management system(BMS) using the lead-acid and lithium-ion batteries, in order to maximize advantage of each battery. In other words, this paper proposed the algorithm of state of charge(SOC) and hybrid operation algorithm to calculate the optimal composition rate considering the fixed cost and operation cost of each battery. From the simulation results, it is confirmed that the proposed algorithms are an effective tool to evaluate SOC and to optimally operate hybrid ESS.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.3
• /
• pp.246-251
• /
• 2013

Screen printing is commonly used to form the front/back electrodes in silicon solar cell. But it has caused high resistance and low aspect ratio, resulting in decreased conversion efficiency in solar cell. Recently the plating method has been combined with screen-printed c-Si solar cell to reduce the resistance and improve the aspect ratio. In this paper, we investigated the effect of light induced silver plating with screen-printed c-Si solar cells and compared their electrical properties. All wafers were textured, doped, and coated with anti-reflection layer. The metallization process was carried out with screen-printing, followed by co-fired. Then we performed light induced Ag plating by changing the plating time in the range of 20 sec~5min with/without external light. For comparison, we measured the light I-V characteristics and electrode width by optical microscope. During plating, silver ions fill the porous structure established in rapid silver particle sintering during co-firing step, which results in resistance decrease and efficiency improvement. The plating rate was increased in presence of light lamp, resulting in widening the electrode with and reducing the short-circuit current by shadowing loss. With the optimized plating condition, the conversion efficiency of solar cells was increased by 0.4% due to decreased series resistance. Finally we obtained the short-circuit current of 8.66 A, open-circuit voltage of 0.632 V, fill factor of 78.2%, and efficiency of 17.8% on a silicon solar cell.

• Current Photovoltaic Research
• /
• v.7 no.3
• /
• pp.65-70
• /
• 2019

As a demand of higher power photovoltaic modules, shingled, multi-busbar, half-cell, and bifacial techniques are developed. Multi-busbar module has advantage for large amount of light havesting. And, half-cell is high power module for reducing resistive losses and higher shade tolerance. Recently, researches on multi-busbar is focused on reliability according to adhesion and intermetallic compound between Sn-Pb solder and Ag electrode. And half-cell module is researched to comparing with full-sized cell module for structure difference. In this study, we investigated the factors affecting to efficiency and adhesion of multi-wires half-cell module according to wire thickness, solder thickness, and flux. The results of solar simulator and peel test was that peel strength and efficiency of soldered cell is not related. But samples with flux including high solid material showed high efficiency. The results of FE-SEM and EDX line scan on cross-section between wire and Ag electrode for different flux showed thickness of solder joint between wire and Ag electrode is increasing through solid material increasing. Flux including high solid material would affect to solder behavior on Ag electrode. Higher solid material occurred lower growth of IMC layer because solder permeate to sider of wire ribbon than Ag electrode. And it increased fill factor for high efficiency. In soldering process, amount of solid material in flux and solder thickness are the factor related with characteristic of soldered photovoltaic cell.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.15 no.1
• /
• pp.71-78
• /
• 2020

In the case of power generation using renewable energy, power production may not be smooth due to the influence of the weather. The energy storage system (ESS) is used to increase the efficiency of solar and wind power generation. ESS has been continuously fired due to a lack of battery protection systems, operation management, and control system, or careless installation, leading to very big casualties and economic losses. ESS stability and battery protection system operation management technology is indispensable. In this paper, we present a battery level calculation algorithm and a failure prediction algorithm for ESS optimization and stable operation. The proposed algorithm calculates the correct battery level by accumulating the current amount in real-time when the battery is charged and discharged, and calculates the battery failure by using the voltage imbalance between battery cells. The proposed algorithms can predict the exact battery level and failure required to operate the ESS optimally. Therefore, accurate status information on ESS battery can be measured and reliably monitored to prevent large accidents.

• Journal of Korean Society of Transportation
• /
• v.33 no.3
• /
• pp.284-293
• /
• 2015

The objective of this paper is to determine the conditions of road surface by utilizing the images collected from closed-circuit television (CCTV) cameras installed on roadside. First, a technique was examined to detect wet surfaces at nighttime. From the literature reviews, it was revealed that image processing using polarization is one of the preferred options. However, it is hard to use the polarization characteristics of road surface images at nighttime because of irregular or no light situations. In this study, we proposes a new discriminant for detecting wet and dry road surfaces using CCTV image data at night. To detect the road surface conditions with night vision, we applied the wavelet packet transform for analyzing road surface textures. Additionally, to apply the luminance feature of night CCTV images, we set the intensity histogram based on HSI(Hue Saturation Intensity) color model. With a set of 200 images taken from the field, we constructed a detection criteria hyperplane with SVM (Support Vector Machine). We conducted field tests to verify the detection ability of the wet road surfaces and obtained reliable results. The outcome of this study is also expected to be used for monitoring road surfaces to improve safety.

• Current Photovoltaic Research
• /
• v.4 no.3
• /
• pp.108-113
• /
• 2016

III-V compound semiconductor based thin film solar cells promise relatively higher power conversion efficiencies and better device reliability. In general, the thin film III-V solar cells are fabricated by an epitaxial lift-off process, which requires an $Al_xGa_{1-x}As$ ($x{\geq}0.8$) sacrificial layer and an inverted solar cell structure. However, the device performance of the inversely grown solar cell could be degraded due to the different internal diffusion conditions. In this study, InGaP/GaAs double-junction solar cells are inversely grown by MOCVD on GaAs (100) substrates. The thickness of the GaAs base layer is reduced to minimize the thermal budget during the growth. A wide band gap p-AlGaAs/n-InGaP tunnel junction structure is employed to connect the two subcells with minimal electrical loss. The solar cell structures are transferred on to thin metal films formed by Au electroplating. An AlAs layer with a thickness of 20 nm is used as a sacrificial layer, which is removed by a HF:Acetone (1:1) solution during the epitaxial lift-off process. As a result, the flexible InGaP/GaAs solar cell was fabricated successfully with an efficiency of 27.79% under AM1.5G illumination. The efficiency was kept at almost the same value after bending tests of 1,000 cycles with a radius of curvature of 10 mm.