• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2007.10a
• /
• pp.180-184
• /
• 2007

For driving a sinusoidal type permanent magnet synchronous motor with a maximum continuous torque, a $120^0$ delayed three phase sinusoidal current input which matched with the absolute rotor position is needed at a stator coil. So, the detection of absolute rotor position is required inevitably. Thus the right angle relationship between stator magnetic field and rotor magnetic field has to be preserved at a stator by this commutation action. The detection of a absolute position for the commutation can be made generally by the output signal analysis of the encoder attached at a motor shaft. This study purposes to design signal processing logic circuits which can detect the absolute position of motor with a modem encoder system and generate the three reference wave for making sinusoidal current input at a stator coil.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.2
• /
• pp.119-125
• /
• 2004

This paper is described the indirect induction heated boiler system and induction heated hot air producer using the voltage-fed series resonant high-frequency inverter which can operate in the frequency range from 20〔KHz〕 to 50〔KHz〕. A specially designed Induction heater, which is composed of laminated stainless assembly with many tiny holes and interconnected spot welding points between stainless plates, is inserted into the ceramic type vessel with external working coil. This working coil is connected to the resonant inverter. In the induction heater, it's primary heating section creates low-pressure saturated steam and secondary heating section generates heat distribution evaporating fluid from the turbulence fluid which is flowing through the vessel. The operating performances of this unique appliance in next generation and its effectiveness are evaluated and discussed from the practical point of view.

• Journal of Biomedical Engineering Research
• /
• v.23 no.3
• /
• pp.227-233
• /
• 2002

The IME(implantable middle ear) system is Promising due to its ability to free from sound feedback and Produce a good sound quality and intelligibility with low distortion even if it is operated with high gain for severe hearing impaired. The differential electromagnetic vibration transducer. which was developed for using in IME system and has two small magnets attached the same Pole facing in the coil. is not influenced by environmental external magnetic field. Besides, it has high vibration efficiency and good frequency response characteristics. In this Paper, using acoustic model of the transducer and ear model of normal Person. the signal transfer characteristics of the IME system are analyzed and investigated From the differences of the characteristics between normal ear and the IME system, it is Possible that design of the IME system that have the signal transfer characteristics similar to normal person's ear.

• Journal of the Korean Vacuum Society
• /
• v.6 no.1
• /
• pp.85-90
• /
• 1997

A new ionized sputtering process was developed to fill small trench or via using additional ionizing mechanism of sputtered particles from 32cm $AlCu_x$(x=0.5%) cathode target with rotating magnet, then drawn toward substrate by small negative DC potential. The radial uniformity in RFI magnetron sputtering was studied by plasma diagnosis and appropriate RFI coil design to improve it. Optical emission intensities of excited species. $Ar^{\circ}, \;Ar^+;Al^+, \;Al^{\circ}$ are measured across the radial direction and showed close correlation with deposit's bottom to top thickness ratios in trenches and vias of submicron opening and 1.5 aspect ratio. After increase of the diameter of RF coil from 29 cm to 32 cm and improved the power leading feedthrough symmetry by removal of asymmetric single turn region, there was an increase of uniformity from 7.5% to 1.5% in bottom to top thickness ratio in 0.6 $\mu\textrm{m}$ vias.

• Journal of the Korean Magnetics Society
• /
• v.11 no.1
• /
• pp.38-44
• /
• 2001

The magnetic field standard below 1 mT with the resolution of 0.26 nT has been established. Earth magnetic field (EMF) is compensated automatically down to 0.1 nT/10 min. by a closed feedback system with Cs optical pumping magnetometer and 3-axis Helmholtz coils in nonmagnetic facilities. A multi-layer precision solenoid with the optimized single-current method generates the uniform magnetic field better than 1.0$\times$10$\^$-7/ within $\pm$ 1 cm region at its center. The coil constant of solenoid determined from Helium optical pumping magnetometer is 1.231 058 9 mT/A, and temperature coefficient is 0.38 nT/$\^{C}$. This standard system is used for calibration of low field magnetometers and testing relates to low field.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.2
• /
• pp.149-155
• /
• 2014

In this paper, we study the complex mobile antenna for WPT(Wireless Power Transfer) with NFC(Near Field Communication) of inductive coupling using FPCB which has half thickness compared with the existing coil type antennas. Considering the pattern thickness of loop antenna, the analysis of electromagnetic wave absorber and battery's influence, absorber thickness, the ranges of design parameters are obtained. The proposed antenna has 0.45 mm thickness using single layer 3 oz FPCB and absorber. From measurement, the characteristics of NFC antenna can be satisfied with the specifications of EMVCo. and domestic mobile telecommunication and the transmission efficiency of the proposed WPT antenna is 68.1 % which is competitive with the existing coil type antenna. From the results of this paper, it has been confirmed that the proposed antenna can be used as the WPT and NFC antenna for mobile phone. Key words: Wireless Power Transfer, Near Field Communication, Mobile Phone Antenna, Absorber, FPCB.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.19 no.9
• /
• pp.640-646
• /
• 2007

The cooling heat transfer coefficient of $CO_2$ (R-744) for tube and coil diameter (CD), inclined angle of tube and coil pitch of inclined helical coil type copper tubes were investigated experimentally. The main components of the refrigerant loop are a receiver, a variable-speed pump, a mass flow meter, a pre-heater and a inclined helical coil type gas cooler (test section). The test section consists of a smooth copper tube of 2.45 and 4.55 mm inner diameter (ID). The refrigerant mass flukes were varied from 200 to 800 [$kg/m^2s$] and the inlet pressures of gas cooler were 7.5 to 10.0 [MPa]. The heat transfer coefficients of $CO_2$ in inclined helical coil tube with 2.45 mm ID are $5{\sim}10.3%$ higher than those of 4.55 mm. The heat transfer coefficients of 41.35 mm CD are $8{\sim}32.4%$ higher than those of 26.75 mm CD. Comparison between $45^{\circ}\;and\;90^{\circ}$ of coil angle, the heat transfer coefficients of $45^{\circ}$ are higher than those of $90^{\circ}$. For coil pitch of gas cooler, the heat transfer coefficients of inclined helical coil gas cooler with coil pitch of 5 mm are similar to those of 10 and 15 mm.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.5
• /
• pp.1018-1024
• /
• 2011

For the driving of the sinusoidal type permanent magnet synchronous motor with a maximum continuous torque, the 1200 delayed three phase sinusoidal current inputs which matched with the absolute rotor position are needed at the stator coil. Therefore, the detection of a absolute rotor position is required inevitably. And the right angle relationship between stator magnetic field and rotor magnetic field has to be preserved at a stator by this commutation action. The detection of a absolute position for the commutation can be made generally by the output signal analysis of the encoder attached at a motor shaft. The purposes of this study are to design signal processing logic circuits which could detect the absolute position of motor with a modern encoder system and generate the three reference wave for making sinusoidal current input at a stator coil.

• Journal of the Korean Institute of Gas
• /
• v.7 no.4 s.21
• /
• pp.7-13
• /
• 2003

This study was carried out to optimize premixed burner and heat exchanger of the condensing gas boiler which can save energy by utilizing latent heat of combustion gas and reduce pollutant in exhaust gas. The heat exchanger of the gas boiler was composed of three parts, which were an upper, lower, and coil heat exchanger. The upper heat exchanger was placed outside of the premixed burner and a lower heat exchanger was located under the upper heat exchanger. And, coil heat exchanger rounded the outer surface of an upper and lower heat exchanger. The boiler designed by this research reaches turn-down ratio 4:1 in the domain of equivalence ratio 0.75${\~}$0.8 and thermal efficiency of $97\%$. Emission of NOx and CO concentration was under 20ppm and 140ppm at equivalence ratio 0.8. When diameter of the burner is replaced from 60mm to 50mm, emission of CO was reduced about 50ppm remarkably.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.25 no.5
• /
• pp.65-72
• /
• 2021

700 W class laboratory model Hall thruster, which can be used for the orbit control or station keeping of small satellites, was developed. The size of the discharge channel was determined using a scaling law, and the magnetic field was designed to be symmetric with respect to the midline of the discharge channel and to be maximized outside the discharge channel. Base pressure of a vacuum chamber was maintained below 2.0×10^-5 Torr during experiments, and the thrust was measured by a thrust stand. The anode flow rate and coil current were varied with the fixed anode voltage at 300 V. Under the operation condition at 2.36 mg/s anode flow rate and 2.4 A coil current, performance was optimized as 38 mN thrust, 1,540 s total specific impulse, and 50 % anode efficiency at 620 W anode power.