• Journal of Korean Ophthalmic Optics Society
• /
• v.10 no.3
• /
• pp.185-191
• /
• 2005

Photo-reactive $TiO_2$ thin films on soda-lime-silica slide glass were prepared by spin coating technique with a Ti-naphthenate precursor. Optical, structural and photo-catalytic properties of the films after annealing at $500^{\circ}C{\sim}600^{\circ}C$ were evaluated. As increase with annealing temperature, absorption bands and total transmittance of the films showing an average transmittance (about 80%) at visible spectra range were shifted to UV spectra range and slightly decreased. Refractive index and thickness of the films were increased from 2.16 to 2.63 and decreased from 484 nm to 439 nm, respectively, with increase of annealing temperature. Anatase phase was visible at all annealing temperature. More rougher surface structure was obtained at $600^{\circ}C$ than those of films annealed at $500^{\circ}C$ and $550^{\circ}C$. The hydrophilic conversion was found within 45 min by UV stimulation and optical activation was UVC>UVA>UVB at the case of $500^{\circ}C{\sim}550^{\circ}C$ and UVA>UVC>UVB at the annealing temperature of $600^{\circ}C$. The lowest initial contact angle was obtained at $600^{\circ}C$.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.11a
• /
• pp.463-466
• /
• 2006

직접 알콜 연료전지는 액체인 알콜을 직접 연료전지에 공급하여 연소시킴으로써 높은 효율을 갖는 휴대용전원으로 주목받는 장치이다. 직접 알콜 연료전지에 담지체로 사용되는 탄소 소재는 넓은 표면적과 우수한 전기전도도를 가지고 있다는 장점 있으나 금속 촉매와의 상호작용이 약하여 촉매 활성에 영향을 주지 못한다. 산화물을 담지체로 사용할 경우 이러한 금속-담지체 간의 상호작용으로 인한 촉매활성 증가 및 입자성장 억제의 효과를 기대할 수 있다. 본 연구에서는, 안티몬 도핑된 주석산화물 (Sb-doped SnO2 : ATO nanoparticle)을 직접 메탄올 연료전지용 담지체어 적용하였으며 합성 과정은 다음과 같다. SnC14 5H2O SbC13, NaOH, HCl 수용액 혼합물을 삼구 플라스크에 넣고 $100^{\circ}C$ 온도에서 환류(reflux) 시킨 후 세척 및 건조하여 Air 분위기에서 열처리하였다. 합성된 산화물 수용액에 폴리올 방법으로 합성된 백금 콜로이드를 담지하였으며, 세척과 건조를 통하여 산화물에 담지된 백금 촉매를 촉매를 합성하였다. 촉매의 구조분석을 위해 XRD, TEM을 사용하였으며, 전극촉매로서의 활성을 평가하기 위해 cyclic voltammetry을 평가하였다. 본 연구에서는 백금의 담지량에 따른 Costripping voltammetry특성과 메탄올 및 에탄올 산화 반응 특성에 대하여, 탄소를 담지체로 사용한 Pt/C 촉매와 비교 평가하였다. 알콜 산화반응 평가결과, 주석산화물에 담지한 촉매가 탄소를 담지체로 사용한 촉매보다 우수한 활성을 나타내었으며 활성증가는 메탄올에 비해 에탄올 산화 반응의 경우 크게 증가하였다. 막과 비교해 보았다. $ZrO_2$ 입자는 전도성이며 동시에 친수성을 나타내기 때문에 상용 막에 비하여 함수율 및 수소이온 전도도가 우수하게 나타났다. 복합막의 이러한 물성은 $100^{\circ}C$이상의 고온에서 전해질 막 내의 물 관리를 용이하게 한다. 단위 전지 운전 온도 $130^{\circ}C$, 상대습도 37%의 운전 조건에서도 상당히 우수한 전지 성능을 보임에 따라 고온/저가습 조건에서 상용 Nafion 112 막보다 우수한 막 특성을 나타냄을 확인하였다.소/배후방사능비는 각각 $2.18{\pm}0.03,\;2.56{\pm}0.11,\;3.08{\pm}0.18,\;3.77{\pm}0.17,\;4.70{\pm}0.45$ 그리고 $5.59{\pm}0.40$이었고, $^{67}Ga$-citrate의 경우 2시간, 24시간, 48시간에 $3.06{\pm}0.84,\;4.12{\pm}0.54\;4.55{\pm}0.74 $이었다. 결론 : Transferrin에 $^{99m}Tc$을 이용한 방사성표지가 성공적으로 이루어졌고, $^{99m}Tc$-transferrin의 표지효율은 8시간까지 95% 이상의 안정된 방사성표지효율을 보였다. $^{99m}Tc$-transferrin을 이용한 감염영상을 성공적으로 얻을 수 있었으며, $^{67}Ga$-citrate 영상과 비교하여 더 빠른 시간 안에 우수한 영상을 얻을 수 있었다. 그러므로 $^{99m}Tc$<

• Membrane Journal
• /
• v.33 no.4
• /
• pp.191-200
• /
• 2023

Polyethersulfone (PES) is a widely employed membrane material for water and industrial purification applications owing to its hydrophilicity and ease of phase separation. However, PES membranes and filters prepared using the nonsolvent induced phase separation method often encounter significant flux decline due to pore clogging and cake layer formation on the dense membrane surfaces. Our investigation revealed that tight microfiltration or loose ultrafiltration membranes can be subject to physical fouling due to the formation of a dense skin layer on the bottom side caused by water intrusion to the gap between the shrank membrane and the substrate. To investigate the effect of the bottom surface porosity on membrane fouling, two membranes with the same selective layers but different sub-layer structures were prepared using single and double layer casting methods, respectively. The double layered PES membrane with highly porous bottom surface showed high flux and physical fouling tolerance compared to the pristine single layer membrane. This study highlights the importance of physical optimization of the membrane structure to prevent membrane fouling.

• KSBB Journal
• /
• v.20 no.4
• /
• pp.253-259
• /
• 2005

This study was accomplished using attached $A^2/O$ process that contains nonsurface-modified and surface-modified polyethylene media inside the Anaerobic/Anoxic, Oxic tank, respectively. We could make the hydrophobic polyethylene media have hydrophilic characteristics by radiating ion beam on the surface of the media. The objectives of this study is to investigate the removal efficiencies of the organics and nitrogen when the step feed ratio of raw wastewater into anaerobic and anoxic tank is changed. In this case, we assumed that the denitrification rate can be improved because the nitrifiers in anoxic tank can perform denitrification using RBDCOD instead of artificial carbon sources (for example, methanol, etc.). The wastewater injection rate into anaerobic/anoxic tank was set up by the ratio of 10 : 0, 9 : 1, 8 : 2, 6 : 4, and the results of BOD removal efficiency showed similar trends with $93.3\%,\;92.6\%,\;92.4\%\;and\;91.6\%$, respectively. But the BOD removal efficiency (utilization of the organics) in the anoxic tank was in the order of 9 : 1 $(84.8\%)$, 10 : 0 $(77.0\%)$, 8 : 2 $(75.3\%)$, and 6 : 4 $(61.1\%)$. The T-N removal efficiency was most high when the ratio is 9 : 1 $(67.4\%)$, and other conditions, 10 : 0, 8 : 2, 6 : 4, showed $61.3(\%),\;60.7\%,\;55.5\%$, respectively; the ratio 6 : 4 was found to be lowest T-N removal efficiency, lower than the ratio 9 : 1 by $12\%$. Though the nitrification rate of the ratio 10 : 0, 9 : 1, and 8 : 2 showed similar levels, the ratio 6 : 4 showed considerable inhibition of nitrification, ammonia was the great portion of the effluent T-N. The advantages of this process is that this process is cost-saving, and non-toxic methods than injecting the artificial carbon source.

• Economic and Environmental Geology
• /
• v.53 no.2
• /
• pp.213-220
• /
• 2020

When CO₂ foam is injected into the saline aquifer, the relative permeability of CO₂ decreases and its viscosity increases, thereby reducing mobility in porous media and ultimately improving CO₂ storge with enhanced sweep efficiency. In general, surfactants were used to fabricate CO₂ foam. Recently, nanoparticles have been used to form stable foam than surfactant. This paper introduces CO₂ storage technology using nanoparticle stabilized CO₂ foam. If the surface of the hydrophilic nanoparticles is partially modified into a CO₂-philic portion, the particles have an affinity for CO₂ and water, thus forming a stable CO₂ foam even in deep saline aquifers under high temperature and high salinity conditions, thereby it can be stored in the pores of the rock. In terms of economics, injection method using nanopaticle-stabilized CO₂ foam is more expensive than the conventional CO₂ injection, but it is estimated that it will have price competitiveness because the injection efficiency is improved. From an environmental point of view, it is possible to inject chemical substances such as surfactants and nanomaterials into aquifers or reservoirs for specific purposes such as pollutant removal and oil production. However, some studies have shown that nanoparticles and surfactants are toxic to aquatic animals, so environmentally proven substances should be used. Therefore, further research and development will be needed to study the production and injection of nanoparticle-stabilized CO₂ foam that are environmentally safe and economically reasonable.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.38 no.1
• /
• pp.75-82
• /
• 2012

Natural moisturizing factors (NMFs) are hydrophilic and water-soluble components in stratum corneum of the skin. NMFs absorb water from outer environment and enhance the water-holding capacity of stratum corneum and thereby, prevent the dryness and increase flexibility and plasticity of skin. NMFs are mainly composed of amino acids and their metabolites that are produced from the degradation of filaggrin. Here we established a simultaneous quantification method for 22 amino acids in tape-stripped stratum corneum samples using UPLC-PDA. With this method, we analyzed amino acid contents from tape-stripped stratum corneum samples of forearm and forehead regions from 15 healthy volunteers. Amino acid contents of inner (or upper) region were higher than outer (or lower) region of stratum corneum. Amino acid contents of stratum corneum of forearm were higher by 1.5 fold than forehead region. Of note, total amino acid contents were significantly and inversely correlated with trans-epidermal water loss (TEWL), an index for skin barrier function. Especially, Ser, Glu, Gly, Ala and Thr were determined to positively affect skin mositurizing activities. In conclusion, we could demonstrate that amino acid contents of stratum corneum are closely linked with skin barrier and moisturizing function, providing an important and fundamental methodology for the study of amino acids in skin physiology.

• Korean Chemical Engineering Research
• /
• v.46 no.4
• /
• pp.799-805
• /
• 2008

In general, anionic and cationic surfactants are incompatible because their mixtures form insoluble complexes and precipitate in the water. There are, however, some equimolar complexes of anionic and cationic surfactant that are soluble and behave like regular surfactants, specifically like nonionic surfactants, thus named pseudo-nonionic surfactant complexes. Pseudo-nonionic complexes are more effective and efficient in surface activities than their ionic surfactant components as shown by their equilibrium and dynamic surface tensions. They pack at the interface more than their ionic components. When a novel cationic surfactant, diglyceryl dodecyl dimethyl ammonium chloride(DGDAC), having the polyhydroxyl group at the hydrophilic head group, was mixed with a conventional anionic surfactant (sodium dodecyl sulfate; SDS) at equimolar ratio, we found that the aqueous equimolar mixture showed strong positive synergism in which molecular interaction parameter ${\beta}^M$ was very low, -17.2. According to the studies of equilibrium phase behavior and microscopy, this mixed system could form homogenous solutions containing vesicles.

• Polymer(Korea)
• /
• v.29 no.5
• /
• pp.440-444
• /
• 2005

An increase in the surface area of drugs by reducing particle sizes from microns to nanometers has been known as an efficient method to improve the bioavailability of water-insoluble drugs. To prevent drug nanoparticles from aggregation during the processes of drug formulation, a limited number of pharmaceutical inactive ingredients such as hydroxypropyl cellulose has been employed as stabilizers or dispersants. In this study, copolymers of hydrophilic and hydrophobic amino acids were synthesized by the ring opening polymerization of their N-carboxyanhydride monomers and evaluated as novel candidates to stabilize the nanoparticles of a water insoluble drug, naproxen. Naproxen nanoparticles stabilized by synthesized amino acid copolymers were successfully prepared in the size of $200\~500nm$ in 60 min by a wet comminution process. Particle size analysis showed that the effective stabilization performance of copolymers required the hydrophobic moiety content to be higher than $10 mol\%$. However, the molecular weight and morphology of copolymers was not the critical parameters in determining the particle size reduction. Their particle size was found to be stable up to 14 days without significant aggregation.

• Restorative Dentistry and Endodontics
• /
• v.30 no.6
• /
• pp.435-441
• /
• 2005

The purpose of this study was to evaluate the effect of increasing application time of single bottle adhesives (SBA) to microtensile bond strength (MTBS) of dried dentin. To expose the superficial dentin surfaces, human molars were sectioned perpendicular to the long axis of tooth. $32\%$ phosphoric acid gels were applied for 15s and rinsed. The teeth were randomly assigned to 3 groups ; S group (Single Bond), O group (One-Step), P group (Prime & Bond NT). Each group was divided to 3 subgroups (W: dentin wipe with wet gauge and light cured immediately, D, dentin dried for 30s and light cured immediately, 30: dentin dried for 30s and light cured after applying SBA for 30s). Composite resin was built up on the dentin surface and sectioned to obtain 20 specimens with $1mm^2$ cross sectional area and the MTBS was measured. For Single Bond, the mean MTBS of S-W and S-30 group were higher than that of S-D group statistically (P<0.05). For One-Step, the mean MTBS of O-D group was statistically lower than that of O-W group (P<0.05). For Prime & Bond NT, the mean MTBS of P-30 group was statistically lower than that of P-D group (P<0.05).

• Journal of the Mineralogical Society of Korea
• /
• v.32 no.3
• /
• pp.201-211
• /
• 2019

The particle size and crystallinity of fault gouge generally decreases with slip. Phyllosilicates including talc are known to be present in fault gouge and play an important role in fault weakening. In particular, the coefficient of friction varies depending on the presence of a water molecule on the surface of mineral. The purpose of this study is to investigate the effect of talc on fault weakening by changing the water content and dehydration behavior of talc before and after grinding, which systematically varied particle size and crystallinity using high energy ball mill. Infrared spectroscopy and thermal analysis show that the as-received talc is hydrophobic before grinding and the water molecule is rarely present. After grinding up to 720 minutes, the particle size decreased to around 100 ~300 nm, and in talc, where amorphization proceeded, the water content increased by about 8 wt.% and water molecule would be attached on the surface of talc. As a result, the amount of vaporized water by heating increased after grinding. The dihydroxylation temperature also decreased by ${\sim}750^{\circ}C$ after 720 minutes of grinding at ${\sim}950^{\circ}C$ before grinding due to the decrease of particle size and crystallinity. These results indicate that the hydrophobicity of talc is changed to hydrophilic by grinding, and water molecules attached on the surface, which is thought to lower the coefficient of friction of phyllosilicates. The repeated slip throughout the seismic cycle would consistently lower the coefficient of friction of talc present in fault gouge, which could provide the clue to the weakening of matured fault.