• Journal of IKEEE
• /
• v.20 no.2
• /
• pp.152-162
• /
• 2016

Electrical resistivity tomography (ERT) is a technique to reconstruct the internal resistivity distribution using the measured voltages on the surface electrodes. ERT inverse problem suffers from ill-posedness nature, so regularization methods are used to mitigate ill-posedness. The reconstruction performance varies depending on the type of regularization method. In this paper, an interacting dual-mode regularization method is proposed with two different regularization methods, L1-norm regularization and total variation (TV) regularization, to achieve robust reconstruction performance. The interacting dual-mode regularization method selects the suitable regularization method and combines the regularization methods based on computed mode probabilities depending on the actual conditions. The proposed method is tested with numerical simulations and the results demonstrate an improved reconstruction performance.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.22 no.6
• /
• pp.725-733
• /
• 1998

The pressure fluctuation on the surface of a submerged body has been recognized as a dominant noise source. There have been many studies concerning the flow induced noise on a flat plate. However, the noise over an axisymmetric body has not been well reported. This paper addresses the way in which we have investigated the mechanism of noise generation due to an axisymmetric body. The associated experiments and signal processing methods are introduced. A 3-dimensional axisymmetric body whose length and diameter were 2 m and 10.4 cm, was prepared as a test specimen. The wall pressure on the surface of the body was measured in a large scale low noise wind tunnel at KIMM(Korea Institute of Machinery and Metals). To measure the wall pressure, we used two microphone arrays which were tangential and normal to the flow. Based on the measured signal, frequency-wavenumber spectrum which explains the structure of turbulence noise, was estimated. Tangential to the flow, there exists convective ridge at a relatively higher wavenumber region; this can cause spatial aliasing. To circumvent this problem, the cross spectrum was interpolated. The interpolation has been performed by unwrapping the phase and smoothing the cross spectrum. The phase unwrapping was done based on the Corcos model; the phase of cross spectrum decreases linearly with the distance between microphones. Aforementioned signal processings are possible by employing the experimental results that the estimated wavenumber spectrum quite resembles the Corcos model. We try to modify the Corcos model which is applicable to the flat plate, by altering the magnitude of cross spectrum to fit the experimental data more accurately. We proposed that this wavenumber spectrum model is suitable for the 3-dimensional axisymmetric body. Normal to the flow, there exists a little correlation between signals of different microphones. The circumferential wavenumber spectrum contains uniform power along the wavenumbers.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.43 no.5 s.311
• /
• pp.68-79
• /
• 2006

Electrical capacitance tomography (ECT) is a non-invasive imaging reconstruction technique that aims at visualization of cross sectional permittivity distribution of dielectric object based on the measured capacitance. There are lots of iterative image reconstruction methods to accelerate convergence rate and enhance quality of reconstructed image, Among them iterative Landweber method is one of the widely used reconstruction algorithm in En. In this paper, modified generalized Landweber method is proposed to accelerate convergence rate. In doing so, acceleration term is considered to the generalized Landweber method with shaping matrix and an optimal step length is determined analytically. Extensive computer simulations are provided to illustrate the reconstruction performance of the proposed algorithm.

• Journal of Life Science
• /
• v.13 no.1
• /
• pp.83-89
• /
• 2003

To investigate the function of chloroplast small heat shock protein (HSP), transgenic tobacco plants (Nicotiana tabacum L, cv. SR-1) that constitutively overexpress the rice chloroplast small HSP (Oshsp26) were generated. Effects of constitutive expression of the Oshsp26 on thermotolerance were investigated with the chlorophyll fluorescence. After 5-min incubation of leaf discs at high temperatures, an increase in the Fo level, indication of separation of LHCII from PSII, was mitigated by constitutive expression of the chloroplast small HSP When tobacco plantlets grown in Petri dishes were incubated at $20^{\circ}C$/TEX> for 45 min and subsequently incubated at $20^{\circ}C$/TEX> leaf color of wild-type plant became gradually white and all plantlets were finally died. Under the conditions in which all the wild-type plants died, more than 80% of the transformants remained green and survived. It was also found that the levels of Oshsp26 protein accumulated in transgenic plants were correlated with the degree of thermotolerance. These results suggest that the chloroplast small HSP plays an important role in protecting photosynthetic machinery, as a results, increases thermotolerance of whole plant during heat stress.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.4 s.119
• /
• pp.398-407
• /
• 2007

In this paper we proposed the tag antenna with a low performance distortion from an attached surface material using the asymmetric dual-arm dipole antenna(ADDA) structure. The tag is designed to exhibit low performance changes when the tag is attached on a target object(the medical litter receptacle, ${\varepsilon}_r=1.7,\;tan\;{\delta}=0.002$). Detail design parameters for the proposed antenna are optimized to maintain a good readable range in free-space as well as on a target object. The size of the optimized antenna is $100\;mm{\times}50\;mm$. The antenna shows the matching bandwidth($S_{11}$< -10 dB) of 3.7 % and the radiation efficiency of 80 % at the operating frequency. Finally we confirmed the readable range of the tag antenna by measurement and it shows about 5.3 m in free space and 5.5 m on the target object.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.45 no.6
• /
• pp.108-116
• /
• 2008

In this paper, we propose an algorithm that can estimate the distance using disparity based on stereo vision system, even though the obstacle is located in long ranges as well as short ranges. We use sub-pixel interpolation to minimize quantization errors which deteriorate the distance accuracy when calculating the distance with integer disparity, and also we use enhanced adaptive fuzzy strong tracking Kalman filter(EAFSTKF) to improve the distance accuracy and track the path optimally. The proposed method can solve the divergence problem caused by nonlinear dynamics such as various vehicle movements in the conventional Kalman filter(CKF), and also enhance the distance accuracy and reliability. Our simulation results show that the performance of our method improves by about 13.5% compared to other methods in point of root mean square error rate(RMSER).

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.4 no.3
• /
• pp.174-181
• /
• 2011

A new registration method for IR image and EO image is proposed in this paper. IR sensor is applicable to many area because it absorbs thermal radiation energy unlike EO sensor does. However, IR sensor has difficulty to extract and match features due to low contrast compared to EO image. In order to register both images, we used modified SIFT(Scale Invariant Feature Transform) and block processing to increase feature distinctiveness. To remove outlier, we applied RANSAC(RANdom SAample Concensus) for each block. Finally, we unified matching features into single coordinate system and remove outlier again. We used 3~5um range IR image, and our experiment result showed good robustness in registration with IR image.

• Journal of Korea Multimedia Society
• /
• v.12 no.9
• /
• pp.1262-1272
• /
• 2009

In computer graphics, there exist many studies about illumination and radiance for a realistic description of the 3D modeling and rendering. When we see a scene, the scene is lit by a source of light and the radiance of the points by a source in the scene. The radiance has direct light and glight component. The direct light gets lights directly from light source, but the global light gets lights indirectly by interreflections among complicated geometrical components. In this paper, we studied a method for increasing the accuracy of separating direct light and global light components from a scene by using high frequency illumination pattern. For experiments, we applied the separating method of Nayar's and found the best configurations for the separation through the experiments. We improved the separation accuracy of direct and global light by measuring the value of unilluminated area, which depends on the characteristics of object. Furthermore, we enhanced invisible scene of the global light by applying the image filtering technique.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.10
• /
• pp.1897-1904
• /
• 2006

Home service robot must recognize and build map for indoor and components of the house such as furniture and chair etc. The previous researcher has developed a indoor map building system by using CCD camera and ultra sonic sensor. %no stems have some problem in such a way that (1) a distun resolution can be changed according to the number of pixel when we use a CCD camera system, (2) a measured distance can be decreased when it transmitted to the rubber because of being absorbed the sound energy. This paper represents an intelligent sensor controller of module has been developed by using optic PSD(Position Sensitive Detector) sensor any at a low price. To deduce the switching noise from beam power module and diffused reflection noise, we proposed a heuristic soft filter. The performance of the developed system was compared with ultra sonic sensor system by detecting the indoor wall environment. Some experiments were illustrated for the validity of the developed system.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.3 no.4
• /
• pp.867-873
• /
• 1999

Camera calibration is a procedure which calculates internal and external parameters of a camera with the Down world coordinates of the control points. Accurate camera calibration is required for achieving accurate visual measurements. In this paper, we propose a simple and flexible camera calibration using neural networks which doesn't require a special knowledge of 3D geometry and camera optics. There are some applications which are not in need of the values of the internal and external parameters. The proposed method is very useful to these applications. Also, the proposed camera calibration has advantage that resolves the ill-condition as object plane is near parallel image plane. The ill-condition is frequently met in product inspection. For little more accurate calibration, acquired image is divided into two regions according to radial distortion of lens and neural network is applied to each region. Experimental results and comparison with Tsai's algorithm prove the validity of the proposed camera calibration.