• 한국전기화학회:학술대회논문집
• /
• 2004.06a
• /
• pp.293-296
• /
• 2004

고용량 $LiNi_{1-y}M_yO_2$(M=Al, Zn and Ti, y=0.000, 0.005, 0.010, 0.025, 0.050 and 0.100) 양극재료를 합성하기 위하여 연소법을 사용하였다. 합성한 시료들을 X-선회절 분석, 미세구조관찰, 전자침미세분석(EPMA)을 하였다. battery 충${\cdot}$방전기를 사용하여 리튬의 삽입${\cdot}$추출 반응으로 인하여 나타나는 충${\cdot}$방전 곡선의 변화를 조사하였고, 합성한 각 시편에 대해 충${\cdot}$방전 싸이클 수에 따른 방전용량의 변화를 조사하였다. XRD pattern 분석결과 모든 조성에서 $R\bar{3}m$ 구조를 보여주었다. Ni 자리에 Al, Zn, Ti를 치환한 결과 방전용량은 감소하였으나 M=Al 시료는 싸이클 특성이 증가하였다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.9
• /
• pp.733-738
• /
• 1998

본 논문에서는 고체 리듐 전지를 개발하기 위하여 poly(ethylene oxide) [PEO] 에 $LiClO_4$, poly (vinylidene fluoride) [PVDF] 및 가소제로 propylene carbonate [PC] 와 ethylene carbonate[EC] 등을 혼합여 고분자 저해질을 제조하였다. 또한 고체 리듐 전지용 정극으로써 우수한 특성이 기대되는 $Li_xV_3O_8$을 졸-겔법에 의해 합성하여 $Li_xV_3O_8$SPE/Li cell 의 전기화학적 특성을 측정하였다. 고분자 matrix는 PEO와 PVDE를 혼합 사용한 결과 $PEO_4 PVDF_4LiCIO_4PC_5EC_5$ 고분자 전해질이 상온에서 $5.2 {\times} 10{-3}$ S/cm 의 높은 이온 전도도를 나타냈으며 리듐 이온 transference number는 0.3이었다. 졸-겔법에 의해 제조된 $Li_xV_3O_8$을 사용한 $Li_xV_3O_8$SPE/Li cell의 방전시 cell 저항이 방전 초기에는 비소한 증가를 하다가 방전 말기 전압인 2.0V에서 크게 증가하였다. $Li_xV_3O_8$ composite 정극의 첫 번째 방전 용량은 295㎃h/g이었으며 8번째 충방전 싸이클부터 방전 용량이 안정화 되었고 15번째 방전 용량도 212㎃h/g으로 고체 전지용 정극으로써 우수한 특성을 보였다.

• Journal of the Korean Electrochemical Society
• /
• v.11 no.2
• /
• pp.125-129
• /
• 2008

Rechargeable lithium-ion polymer batteries have been considered to be next-generation power sources for portable electronic devices and electric vehicles. In this work, we tried to improve the cycling performances of lithium-ion polymer cells by coating aluminum fluoride and acrylonitrile-methyl methacrylate copolymer to the polyethylene separator. It was found that the addition of aluminum fluoride to the surface-modified separator reduced the interfacial resistances and thus the cell exhibited a less capacity fading and better high rate performance. The cell showed an initial discharge capacity of 150 mAh/g and good capacity retention at 0.5 C rate.

• Journal of the Korean Electrochemical Society
• /
• v.5 no.1
• /
• pp.30-38
• /
• 2002

Disordered carbon and boron-substituted disordered carbons $C_{l-x}B_x(x=0.05,\;0.10,\;0.20)$ were synthesized by Pyrolysis of LPG(liquid Propane gas)and $BCl_3$. Their electrochemical properties as anode materials for Li-ion secondary batteries were then investigated. When PVDF is added to the sample in a weight ratio 5 : 95, the disordered carbon with x=0.00 had the first discharge capacity 374 mAh/g. Its cycling performance was relatively good from the second cycle and it had the discharge capacity 258 mAh/g at the 10th cycle. When PVDF is added to the sample in a weight ratio 5 : 95, the sample with x=0.05 among the samples $C_{l-x}B_x(x=0.05,\;0.10,\;0.20)$ exhibited the largest first discharge capacity 860 mAh/g and discharge capacity 181 mAh/g at the 10th cycle. All the samples had similar cycling performances from the second cycle. The sample $C_{0.90}B_{0.10}$ showed the best electrochemical properties as a anode materials fur Li-ion secondary battery from the view points of the first discharge capacity(853 mAh/g when $10w1.\%$ PVDF is used), cycling performance, discharge capacity(400mAh/g at the 10th cycle when $10wt.\%$ PVDF is used). All the samples showed generally larger charge and discharge capacities when $10wt.\%$ PVDF ratter than $5wt.\%$ PVDF is used. The plateau region in the range of voltage lower than 1.25V becomes larger probably since the structure becomes less disordered by the addition of boron. When boron is added, the charge and discharge capacities decreased suddenly at the second cycle. This may be become only a part of Li are reversibly deintercalated and intercalated and a part of Li which are strongly combined with B are not deintercalated. The increases in charge and discharge capacities are considered to be resulted from the increase in the potential of Li in the boron-added carbons, caused by the strengthening of the chemical bond between the intercalated Li and the boron-carbon host since the boron acts as electron acceptor.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.33 no.2
• /
• pp.198-204
• /
• 2013

Acoustic emission(AE) signal was detected during charge and discharge of lithium ion battery to investigate relationships among cumulative count, discharge capacity, and microdamages. AE signal was received during accelerated charge/discharge cycle test of a coin-type commercial battery. A number of AE signals were successfully detected during charge and discharge, respectively. With increasing number of cycle, discharge capacity was decreased and AE cumulative count was observed to increase. Microstructural observation of the decomposed battery after cycle test revealed mechanical damages such as interface delamination and microcracking of the electrodes. These damages were attributed to sources of the detected AE signals. Based on a linear correlation between discharge capacity and cumulative count, feasibility of AE technique for evaluation of battery degradation was suggested.

• Applied Chemistry for Engineering
• /
• v.10 no.3
• /
• pp.415-418
• /
• 1999

The characteristics of VRLA (valve regulated Iead-acid) battery with the tubular positive plate and gel type electrolyte were examined as a function of active material filling density. The filling density of positive plate was 3.2 g/mL, 3.4 g/mL, and 3.6 g/mL, respectively. These VRLA batteries were cycled with 100% DOD (depth of discharge) at the $C_5/5$ rate, followed by IU-type recharge with $I_{max}=0.2C_{10}/10$ and a final voltage V=2.40 V/cell. The test was performed in a thermostatic room at $25{\pm}1^{\circ}C$. The result indicated that the initial capacity was independent of active material filling density, i.e., the highest initial capacity was 3.4 g/mL of filling density and the lowest was 3.6 g/mL. On aspect of the cycle-life performance of the VRLA battery, the filling density of 3.6 g/mL was similar to that of 3.4 g/mL in the positive plate, and both were higher than that of 3.2 g/mL. Water-loss and degradation of the VRLA battery were decreased according to an increase of the filling density in the positive plate. The optimum filling density of the active material was 3.4~3.6 g/mL.

• Proceedings of the KAIS Fall Conference
• /
• 2007.11a
• /
• pp.144-147
• /
• 2007

최근, 2차전지로서는 타 전지에 비하여 고 에너지 밀도와 고 전압의 특성을 갖고 있는 리튬2차전지가 가장 많이 활용되고 있으며, 이 특성 때문에 전기자동차, 우주왕복선, 분산전원의 한 형태인 전력 저장장치에까지 그 이용이 증대되고 있다. 시스템의 최적성능을 보장하기 위해서는 용도별 싸이클 수명성능을 고려한 충방전 설계 및 이를 위한 전기적 등가모델의 정확성이 필수적이다. 따라서, 본 논문에서는 상용 리튬이차전지의 실제 실험 데이터에 근거하여 충/방전 심도 함수를 도출하고, 리튬이차전지의 수명성능평가를 위한 충/방전 특성 모델을 제안하고, 이의 타당성을 입증하였다.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.2002-2003
• /
• 2007

정보통신매체의 발달로 인한 이차전지의 사용이 증가됨에 따라 향상된 이차 전지의 개발이 요구되고 있는 현재에서 기존 이차전지의 충방전 특성을 시험의 중요성이 부각되고 있다. 이런 시점에서 이차전지의 충방전 특성과 싸이클 및 다이나믹 특성을 컴퓨터상의 시뮬레이션을 통해 신뢰할만한 모델링 기법을 제시하는 것이 이 논문의 목적이다.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.7 no.2
• /
• pp.284-291
• /
• 1997

The electrode characteristics of two kinds of metal hydride electrodes using V-Ti (V-rich) based alloy were studied, in which one electrode was prepared by sintering the mixture of V-Ti alloy and Ni powders by a rapid thermal annealing technique and the other one was prepared using V-Ti-Ni ternary alloy, The discharge capacities of all electrodes during the charge-discharge cycling were completely deteriorated within 10 cycles. It appeared that the deterioration of the electrodes was caused by the dissolution of V in the near-surface region into the electrolyte and the formation of $TiO_2$ layer on the alloy particle surface. This degradation mechanism was supported by the facts that V is main hydride forming element and $TiO_2$ has very low electrical conductivity and hydrogen diffusivity.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2003.11a
• /
• pp.157-160
• /
• 2003

mesocarbon microbeads (MCMB) 카본 분말에 제2상 첨가물로서 소량의 주석산화물$(SnO_2)$을 균일하게 분산 첨가시킴으로서 리튬이차전지의 부극재료로 사용되는 카본 분말의 전지 성능을 개선하였다. 주석산화물 첨가 방법는 전하적정법을 사용하여 Sn을 MCMB 분말에 삽입시키고, 다시 삽입된 Sn이 산화되도록 대기 중에서 $250^{\circ}C$로 1시간동안 후열처리를 하였다. 주석산화물이 첨가된 MCMB 카본분말로 Li/MCMB 전지 cell을 만들어 충방전시험을 수행한 결과, raw MCMB로 만든 전극보다 더 우수한 충방전 용량과 싸이클 특성을 나타내었다. 즉, 주석산화물 삽입에 의해 표면개질된 MCMB 카본 분말은 기존의 MCMB에 비해 높은 초기 방전용량과 충전용량을 나타내었고, 또한 높은 가역 특성과 좋은 cycleability를 보였다. 삽입된 $SnO_2$의 양이 증가할수록 높은 가역용량을 나타내었고 비가역용량 역시 높은 값을 나타내었다.