• Proceeding of EDISON Challenge
• /
• 2013.04a
• /
• pp.393-397
• /
• 2013

관내의 유량을 제어하는 볼 밸브(ball valve)는 개폐각도(opening degree)가 커짐에 따라 출구에서 유속이 증가하고 밸브(valve)의 입 출구 간 압력강하(pressure drop)가 증가한다. 출구에서의 압력이 작동유체의 포화증기압보다 낮아질 때 공동현상(cavitation)이 발생한다. 관내에서의 공동현상은 배관시스템의 진동 및 소음, 부식 등에 있어서 악영향을 미칠 수 있으므로 설계에 매우 중요한 요소이다. 버터플라이 밸브를 비롯한 다른 밸브에서는 공동현상감소에 대한 연구가 많이 이루어졌다. 이에 본 연구에서는 볼 밸브 내 유동 특성(characteristic of flow)과 볼 밸브의 입출구간 압력강하를 줄이는 연구를 수행하였다. 개폐 각도와 그에 따른 압력강하와의 관계를 Edison_전산열유체를 사용하여 분석하고 공동현상을 감소시킨 볼 밸브의 설계를 제시 하였다.

• Journal of the Korean Institute of Gas
• /
• v.12 no.4
• /
• pp.21-28
• /
• 2008

A numerical analysis is achieved to elucidate the behavior of lifted flames and characteristics of flow near flame zone according to the exit velocity of triple flame, Poiseuille and uniform distribution. For the cases of Poiseuille and uniform nozzle exit velocity, we reviewed previous results with the present numerical results and investigated characteristics of the flame structure near the flame zone comparing with liftoff height generalized by momentum flux. In addition, a close inquiry into the combustion flow characteristics near flame zone was made with the characteristics of velocity, pressure, temperature and chemical reaction. From nozzle to flame zone, center line velocity profile traced well with the velocity profile of typical cold jet flow, but very near the flame zone, this study examined phenomenon that flow velocity decreases very quickly before the flame zone and then increases very quickly after the flame zone. Because flame zone acts as a barrier at the flow region which is before the flame zone and accelerate the flow velocity when it pass through the flame zone. This phenomenon was not clarified previous cold jet flow.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.5 no.4
• /
• pp.94-101
• /
• 2001

The shock structure of dual coaxial jet is experimentally investigated. Eight different kinds of coaxial, dual nozzles are employed to observe the major features of the near field shock structure on the supersonic, coaxial, dual jets. Four convergent-divergent supersonic nozzles having the Mach number 2.0 and 3.0 are used to compare the coaxial jet flows discharging from two sonic nozzles. The primary pressure ratio is changed in the range between 1.0 and 10.0, and the assistant jet ratio from 1.0 to 4.0. The results show that the impinging angle, nozzle geometry and pressure ratio significantly affect the near field shock structure, Mach disk location and Mach disk diameter.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.269-273
• /
• 2011

In present paper focused on the influence of the inlet-outlet area ratio of counter flow manifold on the flow distribution and pressure drop characteristics of a tubular heat exchanger. The characteristics of flow distribution and pressure loss can be obtained depending on the inlet-outlet area ratio. In this paper, a tubular heat exchanger can be designed with minimum flow mal-distribution and better characteristic of pressure loss by choosing the optimum inlet-outlet area ratio.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.11 no.4
• /
• pp.19-25
• /
• 2007

A LNG safety valve functions to control a constant pressure inside the LNG line of transportation, and the flow through it accompanies with noise and vibration which affect adversely on the system. The present study aims at understanding the flow physics of LNG safety valve for a practical design of LNG safety valve. A computational work using the two-dimensional, axisymmetric, compressible, Navier-Stokes equations is carried out to simulate the gas flow through the LNG safety valve, and compared with the theoretical results. It is found that the shape of valve sheet and the gap size are the key parameters in determining the gas dynamic forces on the valve sheet, and there exists a distance between nozzle exit and valve sheet in which the thrust coefficient at the valve sheet increases abruptly.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1998.10a
• /
• pp.11-11
• /
• 1998

최적의 액체 램제트 연소기 설계를 위하여 흡입공기와 분무, 혼합 그리고 이에 따른 연소의 일련의 과정이 일어나는 램제트 연소기의 유동해석을 2차원 및 3차원으로 수행하였다. 격자구성은 연소기에 공기를 공급하고 연료를 분무하는 공기 유입관 영역과 연소실 및 노즐 영역, 그리고 출구 대기 영역으로 나누어 독자적으로 격자를 생성시켰다. 연소실 내의 유동 특성에 있어서 2차원과 3차원의 유동해석 결과는 선회영역 유동특성이 크게 차이가 남을 알 수 있었다. 따라서 실제 액체 램제트 연소기의 설계를 위해서는 3차원 유동해석과 실험이 반드시 필요하다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.977-980
• /
• 2011

In this paper, explain to development of low pressure axial compressor performance test rig in KARI. Performance test rig consist of a entrance section, rotor, stator, shaft, rig housing, bearing housing and exit section. Test rig design structural optimization to rotor dynamics analysis of the simplified rotor-shaft assembly and flow analysis of entrance/exit section.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.1
• /
• pp.1-7
• /
• 2006

Linear stability analysis of 2-dimensional wall jet is conducted by using parabolized stability equation (PSE). Wall jet is found to be modelled well by boundary layer approximation except for the neighborhood of the nozzle exit, and the introduction of local similarity variable makes the streamwise basic flow Reynolds number independent. Stability characteristics of the wall jet obtained

• Journal of Biomedical Engineering Research
• /
• v.22 no.1
• /
• pp.35-40
• /
• 2001

압력기반의 유한체적법과 k-$\varepsilon$난류모델을 이용하여 신생아 보육기 내의 삼차원 정상난류유동해석과 대류현상에 의한 열전달을 해석하였다. 보육기 내의 주된 공기유동은 입구에서 유입된 공기가 보육기 위쪽을 지나 출구로 이동하며 각진 구석에서 작은 와류들이 관찰되었다. 보육기의 입구부를 제외한 대부분에서의 유속은 0.1m/s 이하로 나타났으며, 신생아의 다리부분에서의 속도가 머리부분보다 다소 크게 관찰되었다. 입구쪽의 온도가 출구쪽의 온도보다 1~2$^{\circ}C$ 높게 나타났으며 속도 크기가 큰 다리부분에서의 온도가 머리 또는 목부분보다 다소 낮았다. 보육기 내의 온도변화는 약3~4$^{\circ}C$로 다소 크게 나타났는데 이는 입구에서 유입된 공기가 상벽과 직각으로 만나며, 보육기 외벽의 각진 구석부분에 의한 영향으로 생각된다. 따라서 입구속도를 적절히 줄이거나 유선형의 유동을 갖도록 설계하여 열손실을 최소화한다면 보다 효율적인 보육기가 될 것으로 생각된다.

• Journal of the Korea Society of Computer and Information
• /
• v.19 no.2
• /
• pp.161-171
• /
• 2014

In this paper the flow dynamics of the flue gas equipment in the desulfurization system was numerically analyzed by simulating the problems for the turbulent and combustion flow from Induced Draft Fan(I.D.Fan) outlet to Booster Up Fan(B.U.Fan) inlet using the commercial CFD software of CFD-ACE+ in CFDRC company for Computational Fluid Dynamic Analysis. The guide vane of this section was examined for the minimum pressure loss and the uniform flow dynamic to B.U.Fan with the proper velocity from I.D,Fan exit to B,U,Fan inlet section at the boiler both the maximum continuous rating and the design base. The guide vanes at I,D.Fan outlet and B.U.Fan inlet were removed and modified by numerical simulation of the CFD analysis. The flue gas at the system had the less pressure loss and the uniform flow dynamics of the flow velocity and flow line by comparing with the old design equipment.