• Journal of Korean Society of Steel Construction
• /
• v.19 no.1
• /
• pp.117-127
• /
• 2007

In this study, we evaluate the strength of steel box beam-to-column connections subjected to axial loads in steel frame piers. The T-connection strength was reduced due to the column axial force in the two-story pier structure. To examine this phenomenon, non-linear FEM analysis was carried out and the analytical procedure was verified by comparing it with experimental results. To clarify the effect of the axial force and major design parameters in connection with strength, influence of panel zone width-thickness ratio, sectional area, and axial force was investigated using FEM analysis. Also, the theoretical strength equations were suggested by stress distribution of panel zone. The strength of the T-connection was compared with one of the one-story pier structure connections. As a result, the strength evaluation equations are proposed in consideration of the panel zone width-thickness ratio and sectional area ratio for the T-connections.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.19 no.6
• /
• pp.98-104
• /
• 2015

Excessive thrust acting on the rotor of pump can cause the damage of pump or the decrease of pump lifetime. Therefore, for ensuring the safety of LOX pump of a liquid rocket engine, the thrust of pump rotor is estimated by similarity tests. Axial thrust is indirectly measured by an axial thrust measurement unit positioned outside pump. Radial thrust is calculated based on pressure distribution of volute scroll. As a result, axial and radial thrust are increased when the flowrate of pump decreases. However, both thrusts do not affect the stability of pump rotor since their values are not large.

• Journal of the Korea Concrete Institute
• /
• v.13 no.3
• /
• pp.251-260
• /
• 2001

It is required to evaluate the axial strain of reinforced concrete beams in order to predict the ductility of reinforced concrete beams subjected to reversed cyclic loading. A model was proposed to determine the axial strains In reinforced concrete beams by analysing the behavior of reinforced concrete sections and comparing with published test results. The proposed axial strain model inclusively reflected four kinds of paths : Path 1-steel bar in an elastic stage or a unloading region; Path 2-after flexural yielding; Path 3-a slip region; and Path 4-a reversing loading region. The equations to predict the axial strains of each path were proposed. The proposed equations took into account the effects of the loading program. Comparison of axial strains between experimental results and the results from proposed equations showed to be in a good agreement with experimental results.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.4
• /
• pp.64-69
• /
• 2002

Dynamic analysis of laminated beams with a embedded damping layer under tension or compression axial load is investigated. Improved Layer-Wise Zig-Zag Beam Theory and Interdependent Kinematic Relation using the governing equations of motion are incorporated to model the laminated beams with a damping layer and a corresponding beam zig-zag finite element is developed. Flexural frequencies and modal loss factors under tension or compression axial load are calculated based on Complex Eigenvalue Method. The effects of the axial tension and compression load on the frequencies and loss factors are discussed.

• Aerospace Engineering and Technology
• /
• v.3 no.2
• /
• pp.149-159
• /
• 2004

Dynamic analysis of laminated beams with a embedded damping layer under tensional and compressive axial load is investigated. Improved Layer-Wise Zig-Zag Beam Theory and Interdependent Kinematic Relation are incorporated to model the laminated beams with a damping layer and a corresponding beam zig-zag finite element is developed. Flexural frequencies and modal loss factors under tension or compression axial load are calculated based on Complex Eigenvalue Method. The effects of the axial tensional and compressive load on the frequencies and loss factors are discussed.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.3 no.1
• /
• pp.51-62
• /
• 2001

In-situ stress measurement using AE (Acoustic Emission) and DRA (Deformation Rate Analysis) is usually carried out under uniaxial loading in the laboratory and it consumes delay time from drilling to testing. Therefore, it should be considered how the lateral stress and delay time influence on the test results for the in-situ stress determination. As the delay time increased, the accuracy of estimating the pre-stress decreased. The pre-stress of the specimen loaded only axially was determined within an error of less than 9% (using AE) and 4% (using DRA). And the specimen on which axial pre-stress and the confining pressure were loaded had an error of less than 17% (using AE) and 14% (using DRA). The results of AE and DRA for field specimens were very similar with each other but smaller than those of hydraulic fracturing method.

• Journal of Korean Society of Steel Construction
• /
• v.19 no.2
• /
• pp.201-210
• /
• 2007

Double-angle connections should be designed with enough stiffness and strength to properly resist various applied loads. Therefore, structural engineers should be able to predict some influential variables and take their effects into account in design. This study was performed to establish the effects of the number of bolts and bolt gage distance on the stiffness and strength of a double-angle connection under tension. Six experimental tests were conducted to describe the effects of these variables by comparing load-displacement relationship curves. In addition, two prediction models were proposed to estimate the initial stiffness and the maximum allowable tensile load based on the results of experimental tests. In the development of these prediction models, the effect of prying action was considered.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1997.10a
• /
• pp.365-372
• /
• 1997

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.1
• /
• pp.157-162
• /
• 2000

The ball bearings are the widely-used machine elements in many machineries. They support not only the radial and the axial force but also the moment in many cases. To simply determine the limit load which can be maintained on an ball bearing or survived in wanted life, the combined the radial and axial force with the moment is converted to the equivalent radial or axial load. However, it is not easy to calculate the equivalent load on the ball bearings. So the simplified equations to evaluate the dynamic and static equivalent load considering the axial force and moment are proposed in this analysis. And the modified equation for the static equivalent radial load with the moment and the axial load is proposed. It is desired that these equations are effectively refered in designing the machineries where the ball bearings are installed.

• Computational Structural Engineering
• /
• v.11 no.3
• /
• pp.229-239
• /
• 1998

복합재료는 강도-무게비가 다른 재료들에 비해 훨씬 크기 때문에 부재의 좌굴문제가 대단히 중요하게 취급되며, 본 논문에서는 축방향 압축력을 받는 복합재료로 된 쉘 부재의 좌굴해석이 수행된다. 이 재료는 일반적으로 이방성 재료 특성을 나타내 보이나, 섬유들이 한 방향으로만 배치되어 있는 경우 섬유방향에 연직한 평면에서의 강도나 탄성계수들은 모두 일정한 횡 등방성 재료성질을 가진 것으로 간주할 수 있다. 9 절점 degenerate 쉘 유한요소를 사용한 선형안정해석, LUSAS 범용 프로그램을 이용한 구조해석, 그리고 고전적 쉘 좌굴방정식에 의한 해석들을 수행하였으며, 그 결과들을 서로 비교, 분석하였다. 고려된 등방성 재료나 횡 등방성 재료의 경우 모두, degenerate 유한요소해석으로 계산한 임계하중들은 고전적 이론해에 의한 결과들 보다 낮았으며, LUSAS 결과들과는 거의 같았다. 이는 degenerate 유한요소에 의한 선형안정해석 결과들이 안전측에 듬을 의미하며, 복합재료로 된 쉘 구조물의 좌굴해석에 degenerate 유한요소를 효율적으로 적용할 수 있음을 의미한다.