• Korean Journal of Agricultural Science
• /
• v.25 no.2
• /
• pp.260-270
• /
• 1998

The field tests were performed to suggest the rational method for stability evaluation of soft clay. The behavior of settlement-displacement obtained by field monitoring system was to compare and analyze the results of the observationed method, and to investigate the complex behavior of soft clay with filling height. The results of this study are summarized as follows. 1. The horizontal displacement was suddenly increased when physical properties of soft clay showed maximum values and the part of the turning point. The values of these properties were available to the fundamental data for stability evaluation. The shear deformation appeared that difference of the horizontal displacement was maximum values. 2. Although the stability of embankment by step filling showed the unstable part over the failure standard line, the embankment was confirmed stable. So the evaluation of the stability of embankment is reasonable to use the inclination of curve than failure standard line. 3. The horizontal displacement and relative settlement were increased as same ratio at improvement ground. Estimation of shear deformation using Terzaghi's modified bearing capacity should consider the relations of embankment load and undrained shear strength at nonimprovement ground, and minimum safety factor is recommended to use larger than 1.2. 4. Excess pore water pressure was increased with increasing of filling height and decreased with maintain the filling height. The embankment was unstable when filling height was exceed the evaluation standard line, and the behavior of excess pore water pressure and horizontal displacement could use as a standard of judgement of the filling velocity control because their behavior were agree with each other.

• The korean journal of orthodontics
• /
• v.35 no.2 s.109
• /
• pp.137-147
• /
• 2005

The purpose of this study was to investigate the stress distribution in the periodontal tissue and the displacement of teeth when active torque was applied to the maxillary incisors by three-dimensional finite element analysis A three-dimensional finite element model consisted of the maxillary teeth and surrounding periodontal membrane, $.022{\times}.028$ Roth prescription bracket and stainless steel, NiTi and TMA rectangular ideal arch wires which were modeled by hexahedron elements. Applied active torques were 2, 5 and 10 degrees ThHe findings of this study showed that the reaction force acting or the bracket was the extrusion force on the mesial side of the incisors and canine and the intrusion force on the distal side of the incisors and canine. The amount of force and moment was greatest at the lateral incisor. When active anterior labial crown torque was applied. labial crown and distal tipping and Intrusion of the incisors took place. and lingual crown distal tipping and extrusion of the canine occured. An excessive force was concentrated on the lateral incisor, when the stainless steel wire was used NiTi or TMA wire is desirable for torque control.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.15 no.2
• /
• pp.23-33
• /
• 2011

In this study, a CFPBS (Cone-type Friction Pendulum Bearing System) was developed which controls the acceleration delivered to the structure to prevent damage and degradation of the critical communication equipment in case of an earthquake. The isolation performance of the CFPBS was evaluated by numerical analysis. The CFPBS was manufactured in the shape of a cone differenced from the existing FPS (Friction Pendulum System), and a pattern was engraved on the friction surface. The natural frequencies of the CFPBS were evaluated from a free-vibration test with the seismic isolator system consisting of four CFPBSs. In order to verify its earthquake-resistant performance, a numerical analysis program was created from the equation of the CFPBS induced from the equations of motion. A simplified theoretical equation of the CFPBS was proposed to manufacture the equipment which could demonstrate the necessary performance. Artificial seismic waves satisfying the maximum earthquake scale of the Korean Building Code-Structural (KBC-2005) were created and verified to review the earthquake-resistant performance of the CFPBS by numerical analysis. The superstructural mass of the CFPBS and skew angle of the friction surface were considered for numerical analysis with El Centro NS (1940), Kobe NS (1995) and artificial seismic waves. The CFPBS isolation performance evaluation was based on the results of numerical analysis and the executed comparative analysis between the results from numerical analysis and the simplified theoretical equation under the same conditions.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.84-84
• /
• 2000

수소화된 비정질 실리콘(a-Si:H)과 미세결정질 실리콘 ($\mu$c-Si:H)은 저온.건식 공정인 PECVD로 값싼 유리 기판을 사용하여 넓은 면적에 증착이 가능하다는 큰 장점으로 인해 광전소자(photovoltaic device)와 박막 트랜지스터(TFTs)등에 폭넓게 응용되어 왔으며 최근에는 nm 크기의 실리콘 결정(nc-Si)에서 가시광선 영역의 발광 현상이 발견됨에 따라 광소자로서의 특성을 제어하기 위해서는 성장 조건과 공정 변수에 따른 구조 변화에 대한 연구가 선행되어야 한다. 본 연구에서는 UHV-ECR-PECVD 법을 이용하여 H2로 희석된 SiH4로부터 a-Si:H과 $\mu$c-Si:H를 증착하였다. 그림 1은 SiH4 20sccm/H2 50sccm/25$0^{\circ}C$에서 기판의 DC bias를 변화시키면서 박막을 증착시킬 때 나타나는 박막의 구조 변화를 raman spectrum의 To phonon peak의 위치와 반가폭의 변화로 나타낸 것이다. 비정질 실리콘 박막은 DC bias를 증가시킴에 따라 무질서도가 증가하다가 어떤 critical DC bias에서 최대치를 이룬후 다시 질서도가 증가한다. 이온의 충격력에 의해 박막내에 응력이 축적되면 박막의 에너지 상태가 높아지고 이 축적된 응력이 ordering에 대한 에너지 장벽을 넘을 수 있을 만큼 커지게 되면 응력이 풀리면서 ordering이 가능해지는 것으로 생각된다. 그림 2는 수소 결합 형태의 변화이다. 박막의 무질서도가 증가할 경우 알려진 바와 같이 2000cm-1근처의 peak은 감소하고 2100cm-1 부근이 peak이 증가하는 현상을 보였다. 본 논문에서는 여러 공정 변수, 특히 DC bias에 따르는 박막의 구조 변화와 다른 성장 조건(온도, 유량비)이 critical DC bias나 결정화, 결정성 등에 미치는 영향에 대한 분석결과를 보고하고자 한다.등을 이용하여 광학적 밴드갭, 광흡수 계수, Tauc Plot, 그리고 파장대별 빛의 투과도의 변화를 분석하였으며 각 변수가 변화함에 따라 광학적 밴드갭의 변화를 정량적으로 조사함으로써 분자결합상태와 밴드갭과 광 흡수 계수간의상관관계를 규명하였고, 각 변수에 따른 표면의 조도를 확인하였다. 비정질 Si1-xCx 박막을 증착하여 특성을 분석한 결과 성장된 박막의 성장률은 Carbonfid의 증가에 따라 다른 성장특성을 보였고, Silcne(SiH4) 가스량의 감소와 함께 박막의 성장률이 둔화됨을 볼 수 있다. 또한 Silane 가스량이 적어지는 영역에서는 가스량의 감소에 의해 성장속도가 둔화됨을 볼 수 있다. 또한 Silane 가스량이 적어지는 영역에서는 가스량의 감소에 의해 성장속도가 줄어들어 성장률이 Silane가스량에 의해 지배됨을 볼 수 있다. UV-VIS spectrophotometer에 의한 비정질 SiC 박막의 투과도와 파장과의 관계에 있어 유리를 기판으로 사용했으므로 유리의투과도를 감안했으며, 유리에 대한 상대적인 비율 관계로 투과도를 나타냈었다. 또한 비저질 SiC 박막의 흡수계수는 Ellipsometry에 의해 측정된 Δ과 Ψ값을 이용하여 시뮬레이션한 결과로 비정질 SiC 박막의 두께를 이용하여 구하였다. 또한 Tauc Plot을 통해 박막의 optical band gap을 2.6~3.7eV로 조절할 수 있었다. 20$0^{\circ}C$이상으로 증가시켜도 광투과율은 큰 변화를 나타내지 않았다.부터 전분-지질복합제의 형성 촉진이 시사되었다.이것으로 인하여 호화억제에 의한 노화 방지효과가 기대되었지만 실제로 빵의 노화는 현저히 진행되었다. 이것은 quinua 대체량 증가에 따른 반죽의 안정성이 저하되어 버린 것으로 생각되어진다. 더욱이 lipase를 첨가하면 반죽이 분화하는 경향이 보여졌지만 첨가량 75ppm에 있어서 상당히 비용적의 증대가 보였다. 이것은 lipase의 가수분해에 의해

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2000.04a
• /
• pp.48-48
• /
• 2000

효율적인 wet-end시스템의 적용으로 중성 초지시스템의 이점을 최대한 구현하고 이에 따른 초지계의 안정성 및 원가절감 등을 얻기 위해서는 중성 초지 시스템에서 사용되는 사 이즈제 및 사이징 공정에 대한 연구가 매우 중요하다. 현재 중성 사이즈제로는 AKD와 A ASA가 가장 널리 사용되고 있는데, 유럽에서는 주로 AKD가 쓰이고 있으며, 미국에서는 A ASA가 50%정도 사용되고 있다 .. AKD에 비해서 ASA는 사이즈도의 발현이 매우 빨라 사이 즈 프레스에서 사이즈도가 발현되므로 사이즈 프레스에서의 픽엽 조절 및 지절감소에 유리 한 장점을 가지고 있다. 하지만 ASA는 AKD에 비해 반웅성 높아 습부에서의 가수분해되어 초지 조업성을 악화시키는 문제점을 지니고 있다. 이러한 문제를 극복하기 위해서는 ASA 유화액의 정착성을 개선시키기 위한 연구가 시급히 요청되고 있으며 여기에는 ASA의 유화 에 사용되는 양성전분의 최적화가 가장 핵심적인 기술로 평가된다. 현재 ASA용 유화제로는 양성전분이 가장 많이 사용되고 있다. ASA 에멀션 제조에 있 어서 양성전분의 역할은 음전하를 가지고 있는 ASA 입자에 홉착되여 양전하를 부여함으로 써 콜로이드 업자의 안정성을 부여할 뿐만 아니라 섬유와의 정전기적 인력을 유도하여 정착 을 증진시키는 효과를 나타낸다. ASA 유화용으로 쓰이는 양성전분 중에서는 감자전분이 가 장 효과적인 것으로 알려져 있으며 옥수수나 타피오카 둥도 쓰이고 있다. 그러나 국내의 경 우 감자전분은 옥수수전분보다 가격이 비싸다는 단점이 있으므로 저렴한 옥수수 전분을 이 용하여 ASA 유화용 변성전분의 개발이 국내 제지산업의 경쟁력 강화를 위해 시급히 요망 되고 있다. 본 연구의 목표는 옥수수 전분을 이용한 ASA용 유화안정제를 개발하고 그 효과를 극대 화시킬 수 있는 적용기술을 확립하는데 있다. 옥수수전분을 이용한 ASA 유화용 변성전분은 외국에서 소개된 바가 있기는 하지만 사이즈도 발현이 감자전분의 절반 수준으로 효과적이 지 못한 것이 문제점으로 지적된 바 있다. A ASA 유화용 전분으로는 감자전분과 옥수수전분으로 제조된 외국산 기존 제품과 본 연 구를 통해 개발된 옥수수 전분을 이용하였다. 먼저 실험실적으로 최적의 ASA 에멸션의 유 화가 가능하도록 유화조건을 설정하여 유화액의 입도가 1µm 정도가 되도록 하였다. 이들 A ASA 사이즈제를 Hw. Sw-BKP로 조성된 지료에 투입하여 수초한 후 Hercules 사이즈도 측정기를 이용하여 수초지의 사이즈도를 측정하였다. 또 사이정 효과를 극대화시키기 위한 방안을 모색하기 위해 ASA 에말션의 입도, 제타전위, 탁도 등의 평가를 병행 실시하였다. 실험 결과 기존의 방법으로 유화한 경우 수입감자양성전분이 가장 높은 사이즈도를 보였 다. 그러나, 적절한 전분변성법과 유화조건을 개선함으로써 옥수수전분을 이용하여 수입 감 자전분이나 수입 옥수수전분보다 더 우수한 ASA 사이정 효과를 나타내는 양성전분이 개발 될 수 있음을 확인하였다.

• Journal of Navigation and Port Research
• /
• v.42 no.6
• /
• pp.507-517
• /
• 2018

The probability of T/S cargo volume to decrease is the most notable problem associated with inappropriate mix of terminal operators in Busan port. Other problems include, the deterioration of the national carriers' competitiveness from non-operation of own terminal, excessively high proportion of financial operators in the engagement of operation which may result in their passiveness in timely investment, additional cost burden to carriers' in the handling inter-terminal T/S cargo transportation and inefficiency in terminal operation by the multiplicity of operators proved to be same recognized as so through the analysis. Therefore, in order to provide solutions for the problems and to strengthen Busan port's competitiveness, this research suggests the restructuring of operators mix as follows. To achieve sustainable growth of T/S cargo, global carriers' participation in terminal operation should be of utmost priority. To enhance the operational efficiency, the operators should be integrated. Similarly, the integration of operators will play a key role in verifying that national carriers' own terminal operation is an important factor in raising its competence. Finally, BPA's active engagement in the entire operation of port is also critical in public-oriented operation of the port. Whereas in the interactive analysis by taking the merits of Busan port into consideraion, global carrier's participation in operation, integration of operators and BPA's engagement in operation proved to contribute to the increase of T/S cargo and strengthening of operational efficiencies of Busan port.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.39 no.3
• /
• pp.189-196
• /
• 2003

In this study, the vertical opening of the non-float midwater pair trawl net was maintained by controlling the length of upper warp. This was because the head rope was able to be kept linearly and the working depth was not nearly as changed with the variation of flow speed as former experiments in this series of studies have demonstrated. We confirmed that the opening efficiency of the non-float midwater pair trawl net was able to be developed according to the increase in front weight and wing-end weight. In this study, we described the opening efficiency of the non-float midwater pair trawl net according to the variation of front weight and wing-end weight obtained by model experiment in circulation water channel. We compared the opening efficiency of the proto type with that of the non-float type. The results obtained can be summarized as follows：1. The hydrodynamic resistance was almost increased linearly in proportion to the flow speed and was increased in accordance with the increase in front weight and wing-end weight. The increasing rate of hydrodynamic resistance was displayed as an increasing tendency in accordance with the increase in flow speed. 2. The net height of the non-float type was almost decreased linearly in accordance with the increase in flow speed. As the reduced rate of the net height of the non-float type was smaller than that of the net height of the proto type against increase of flow speed, the net height of the non-float type was bigger than that of the proto type over 4.0 knot. The net width of the non-float type was about 10 m bigger than that of the proto type and the change rate of net width varied by no more than 2 m according to the variation of the front weight and wing-end weight. 3. The mouth area of the non-float type was maximized at 1.75 ton of the front weight and 1.11 ton of the wing-end weight, and was smaller than that of the proto type at 2.0∼3.0 knot, but was bigger than that of the proto type at 4.0∼5.0 knot. 4. The filtering volume was maximized at 3.0 knot in the proto type and at 4.0 knot in the non-float type. The optimal front weight was 1.40 ton.

• Composites Research
• /
• v.12 no.4
• /
• pp.71-78
• /
• 1999

To determine the effect of chemical structure of linear amine curing agents on thermal and mechanical properties, standard epoxy resin DGEBA was cured with diaminodiphenyl methane (DDM), diaminodiphenyl sulphone (DDS) in a stoichiometrically equivalent ratio. From this work, the effect of aromatic amine curing agents. In contrast, the results show that the DGEBA/DDS cure system having the sulfone structure between the benzene rings had higher values in the conversion of epoxide, density, shrinkage (%), glass transition temperature, tensile modulus and strength, flexural modulus and strength than the DGEBA/DDM cure system having methylene structure between the benzene rings, whereas the DGEBA/DDM cure system presented higher values in the maximum exothermic temperature, thermal expansion coefficient, and thermal stability. These results are caused by the relative effects of sulfone group having strong electronegativity and methylene group having (+) repulsive property and stem from the effect of the conversion ratio of epoxide group. The result of fractography shows that the each grain size of the DDM/DGEBA system with feather-like structure is larger than that of the DDS/DGEBA system.

• Journal of Energy Engineering
• /
• v.29 no.2
• /
• pp.68-78
• /
• 2020

According to the new climate change agreement, technology development to reduce greenhouse gases is actively conducted worldwide, and research on energy efficiency improvement in the field of power generation and transmission and distribution is underway [1,2]. Economic analysis of the operation method of storing and supplying surplus electricity using energy storage devices, and using energy storage devices as a frequency adjustment reserve power in regional cogeneration plants has been reported as the most profitable operation method [3-7]. Therefore, this study conducted an economic analysis for the installation of energy storage devices in the combined heat and power plant in the Czech Republic. The most important factor in evaluating the economics of battery energy storage devices is the lifespan, and the warranty life is generally 10 to 15 years, based on charging and discharging once a day. For the simulation, the ratio of battery and PCS was designed as 1: 1 and 1: 2. In general, the primary frequency control is designed as 1: 4, but considering the characteristics of the cogeneration plant, it is set at a ratio of up to 1: 2, and the capacity is simulated at 1MW to 10MW and 2MWh to 20MWh according to each ratio. Therefore, life was evaluated based on the number of cycles per year. In the case of installing a battery energy storage system in a combined heat and power plant in the Czech Republic, the payback period of 3MW / 3MWh is more favorable than 5MW / 5MWh, considering the local infrastructure and power market. It is estimated to be about 3 years or 5 years from the simple payback period considering the estimated purchase price without subsidies. If you lower the purchase price by 50%, the purchase cost is an important part of the cost for the entire lifetime, so the payback period is about half as short. It can be, but it is impossible to secure profitability through the economy at the scale of 3MWh and 5MWh. If the price of the electricity market falls by 50%, the payback period will be three years longer in P1 mode and two years longer in P2 and P3 modes.

• The korean journal of orthodontics
• /
• v.41 no.5
• /
• pp.324-336
• /
• 2011

Objective: The aim of this study was to conduct three-dimensional finite element analysis of individual tooth displacement and stress distribution when a posterior retraction force of 200 g was applied at different positions of the retraction hook on the transpalatal arch (TPA) of a molar, and over different lengths of the lever arm on the maxillary anterior teeth in lingual orthodontics. Methods: A three-dimensional finite element model, including the entire upper dentition, periodontal ligaments, and alveolar bones, was constructed on the basis of a sample (Nissan Dental Product, Kyoto, Japan) survey of Asian adults. Individual movement of the incisal edge and root apex was estimated along the x-, y-, and z-coordinates to analyze tooth displacement and von Mises stress distribution. Results: When the length of the lever arm was 15 mm and 20 mm, the incisal edge and root apex of the anterior teeth was displaced lingually, with a maximum lingual displacement at the lever arm length of 20 mm. When the posterior retraction hook was on the root apex, the molars showed distal displacement. When the length of the lever arm was 20 mm, anterior extrusion was reduced and the crown of the canine displaced toward the buccal side, in which case, the retraction hook was on the edge, rather than at the center, of the TPA. Conclusions: The results of the analysis showed that when 6 anterior teeth were retracted posteriorly, lateral displacement of the canine and lingual displacement of the incisal edge and root apex of the anterior teeth occur without the extrusion of the anterior segment when the length of the lever arm is longer, and the posterior retraction hook is in the midpalatal area.