• Polymer(Korea)
• /
• v.37 no.6
• /
• pp.685-693
• /
• 2013

The foams of a poly(lactic acid) modified by the reactive compounding were produced with the batch foaming technique using supercritical $CO_2(scCO_2)$. Experiments were performed at $105{\sim}135^{\circ}C$ and 12~24 MPa. The blowing ratio and foam structure were significantly affected by changing the temperature and pressure conditions in the foaming process. The blowing ratio first increased with increasing foaming temperature and saturation pressure, reached a maximum and then decreased with a further increase in the foaming temperature and saturation pressure. Decreasing the rate of depressurization permitted a longer period of cell growth and therefore larger microcellular structures were obtained.

• Journal of Advanced Marine Engineering and Technology
• /
• v.28 no.1
• /
• pp.65-74
• /
• 2004

The heat transfer coefficient and pressure drop of $CO_2$(R-744) during gas cooling Process of carbon dioxide in a horizontal tube were investigated experimentally and theoretically. The experiments were conducted without oil in the refrigerant loop. The main components of the refrigerant loop consist of a receiver. a variable-speed pump. a mass flowmeter, an evaporator. and a gas cooler(test section). The main components of the water loop consist of a variable-speed Pump. an constant temperature bath. and a flowmeter. The gas cooler is a counterflow heat exchanger with refrigerant flowing in the inner tube and water flowing in the annulus The test section consists of smooth, horizontal stainless steel tube of 9.53 mm outer diameter and 7.75 mm inner diameter. The length of test section is 6 m. The refrigerant mass fluxes were 200 ~ 300 kg/($m^2{\cdot}s$) and the inlet pressure of the gas cooler varied from 7.5 MPa to 8.5 MPa. The main results were summarized as follows : The predicted correlation can evaluated the R-744 exit temperature from the gas cooler within ${\pm}10%$ for most of the experimental data, given only the inlet conditions. The predicted gas cooley capacity using log mean temperature difference showed relatively food agreement with gas cooler capacity within ${\pm}5%$. The pressure drop predicted by Blasius estimated the pressure drop on the $CO_2$ side within ${\pm}4.3%$. The predicted heat transfer coefficients using Gnielinski's correlation evaluated the heat transfer coefficients on the $CO_2$ side well within the range of experimental error. The predicted heat transfer coefficients using Gao and Honda's correlation estimated the heat transfer coefficients on the coolant side well within ${\pm}10\;%$. Therefore. The predicted equation's usefulness is demonstrated by analyzing data obtained in experiments.

• Polymer(Korea)
• /
• v.36 no.1
• /
• pp.1-8
• /
• 2012

In this study, we employed hydroxypropyl-${\beta}$-cyclodextrin (HP-${\beta}$-CD) as an excipient to produce poly(lactic-$co$-glycolic acid) (PLGA) fine particles by a supercritical fluid process, called aerosol solvent extraction system (ASES), and investigated the effect of HP-${\beta}$-CD content on the morphology of the particles. The influence of HP-${\beta}$-CD on the drug release characteristics of paclitaxel-loaded PLGA particles was also evaluated. Fine particles were obtained when the HP-${\beta}$-CD content in PLGA/HP-${\beta}$-CD mixtures was greater than 40% and 30%, respectively, for PLGA(75:25) and PLGA(50:50), whereas a film-like precipitate was obtained for lower HP-${\beta}$-CD content. The release rate for paclitaxel loaded PLGA(75:25)/HP-${\beta}$-CD particles was found to increase with HP-${\beta}$-CD content.

• Polymer(Korea)
• /
• v.36 no.1
• /
• pp.34-40
• /
• 2012

The foaming of poly(butylene succinate) (PBS) using supercritical $CO_2(scCO_2)$ was studied. In order to improve the melt strength, PBS was modified using the reactive compounding technique. Rapid decompression of $scCO_2$-saturated PBS at a temperature above the depressed $T_m$ yielded expanded microcellular foams. The resulting foam structure could be controlled by manipulating process conditions. Experiments varying the foaming temperature while holding other variables constant showed that higher temperatures produced larger cells and reduced cell densities. Higher saturated pressures led to higher nucleation densities and smaller cell sizes. Decreasing the rate of depressurization permitted a longer period of cell growth and therefore larger cells were obtained.

• Food Engineering Progress
• /
• v.15 no.3
• /
• pp.203-208
• /
• 2011

Effects of particle size and high pressure processing on the extraction rate of oil compounds from soybean powder were evaluated by Soxhlet method using hexane and supercritical fluid extraction (SFE) using $CO_{2}$. SFE was carried out at 4,000 psi and $50^{\circ}C$ for 4 hr. The mean particle sizes were varied from 26.7 to 862.0 ${\mu}m$ by controlling milling time. Saturation solubility increased as the particle size decreased. At large particle size, high pressure processing (HPP) showed higher extraction yield in both hexane extraction and SFE, but, as the particle size decreased, the HPP was irrelevant to the extraction yield in SFE. The higher extraction rate obtained from the smaller particle size. The scanning electronic microscopy of soybean powder treated by HPP showed pores on the surface of the particle. The higher extraction rate and yield from HPP treatment might be due to the less internal resistance of transferring the solvent and miscellar in the solid matrix by collapsing of tissues.

• Applied Chemistry for Engineering
• /
• v.33 no.1
• /
• pp.44-49
• /
• 2022

Essential oil was separated from Dendropanax morbiferus (DM) by means of hot water extraction and supercritical extraction, respectively, and the separated essential oil was analyzed qualitatively and quantitatively, and the antioxidant effect of essential oil was investigated. In addition, yields of essential oil and Caryophyllene according to the drying and extraction methods for each part of DM were obtained and compared, respectively. The yield of essential oil was found to be high in the order of bark > leaves > twigs > limb. When the freeze-dried DM leaves were supercritically extracted, the yields of essential oil and Caryophyllene were 23.2 g/kg DM and 429.6 mg Caryophyllene/kg DM, respectively. The essential oil of DM showed an antioxidant effect even at a low concentration, and the concentration of the essential oil of SC₅₀, which means 50% of 2,2-diphenyl-1-picrylhydrazyl (DPPH) radical scavenging activity, was about 0.34%.

• Journal of the Korean GEO-environmental Society
• /
• v.24 no.6
• /
• pp.5-11
• /
• 2023

The engineering industry heavily relies on fossil fuels such as coal and petroleum to generate energy through combustion. However, this process emits carbon dioxide into the atmosphere, leading to global warming. To mitigate this issue, researchers have explored various methods to reduce carbon dioxide emissions, one of which is carbon dioxide underground storage technology. This innovative technology involves capturing carbon dioxide from industrial plants and injecting it into the saturated ground layer beneath the earth's surface, storing it securely underground. Despite its potential benefits, carbon dioxide underground storage efficiency needs improvement to optimize storage in a limited space. To address this challenge, our research team has focused on improving storage efficiency by utilizing surfactants. Furthermore, we evaluated how different carbon dioxide states, including gaseous, liquid, and supercritical, impact storage efficiency based on their respective pressures and temperatures within the underground reservoir. Our findings indicate that using surfactants and optimizing the injection rate can effectively enhance storage efficiency across all carbon dioxide states. This research will pave the way for more efficient carbon dioxide underground storage, contributing to mitigating the environmental impact of fossil fuels on the planet.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.12
• /
• pp.1415-1420
• /
• 2014

Super-critical $CO_2$ ($S-CO_2$) Brayton cycle has been considered to replace the current steam Rankine cycle in Sodium-cooled Fast Reactor (SFR) in order to improve the inherent safety and thermal efficiency. Several austenitic alloys are considered as the structural materials for high temperature $S-CO_2$ environment.. Microstructural change after long-term exposure to high temperature $S-CO_2$ environment could affect to the mechanical properties. In this study, candidate materials (austenitic stainless steels and Alloy 800HT) were exposed to $S-CO_2$ to assess oxidation resistance and the change in tensile properties. Loss of ductility was observed for some austenitic stainless steels even after 250 h exposure. The contribution of $S-CO_2$ environment on such changes was analyzed based on the characterization of the surface oxide and carburization of the materials in which 316H and 800H showed different oxidation behaviors.

• 제어로봇시스템학회:학술대회논문집
• /
• 1991.10a
• /
• pp.669-675
• /
• 1991

Based on process analysis as well as extensive operation experience, two fuzzy expert control algorithms, for startup and control, are proposed for a supercritical fluid extraction process which has high interacting multivariable structure. In the proposed algorithms, a new simple defuzzification method which only requires four fundamental arithmetic rules is also presented. Through numerical simulations, control performance using the proposed control algorithm is compared with that of a different fuzzy algorithm by an other researcher and that of conventional PID-type controllers which are tuned by well-known optimal criteria. Also, the proposed control algorithm has been tested to the bench scale supercritical fluid extraction process. As a consequence, the proposed fuzzy expert controller has shown fast and robust control performance while the other controllers show sluggish and/or highly oscillatory responses.

• Korean Journal of Acupuncture
• /
• v.26 no.4
• /
• pp.211-223
• /
• 2009

초임계추출법과 수증기증류법을 이용하여 황련해독탕의 정유성분을 추출하여 성분 패턴을 비교하였다. 이때 초임 계추출조건은 압력 200 atm, $45^{\circ}C$ 그리고 추출시간 25분 이었다. 이때의 추출된 성분의 93.9%인 37개의 성분을 가스크로마토그래피/질량분석기로 확인하였다. 주요성분으로는 tetradecenoic acid (11.7%), Vanillin (5.9%), dl-Limonene (5.5%) 및 Eicosane (4.6%)으로 나타났다. 수증기증류법으로 추출한 정유에서는 34개 성분을 확인할수 있었다. 주요성분으로는 tetradecenoic acid (8.9%), Vanillin (5.8%)및 Eicosane (4.7%)를 확인 할 수 있었다. 또한 구강내의 12균주를 이용하여 항균효과를 측정하여 최소엑제농도(MIC)와 사멸농도(MBC) 0.025 - 12.8 mg/ml와 0.05 - 12.8 mg/ml 각각 나타났다.