• Proceedings of the Korea Water Resources Association Conference
• /
• 2023.05a
• /
• pp.315-315
• /
• 2023

급격한 기후변화에 기인하여 전 세계적으로 거듭되는 돌발홍수로 인한 피해가 급격히 증가하고 있는 실정이다. 우리나라에서도 최근 중소 규모의 하천 뿐 아니라 도시 생활하천, 도심지 저지대에서 갑작스런 홍수와 침수로 인해 많은 인명과 재산 피해를 경험하고 있다. 이런 문제를 인식하여 최근 정부차원에서 다양한 센서와 인공지능에 기반하는 많은 인프라 및 연구 투자가 이루어지고 있지만, 높은 설치 및 운영 비용과 우리나라의 복잡한 하천 환경 특성으로 인해 소하천이나 도심지 저지대에서는 그 효율성을 제대로 발휘하지 못하고 있다. 따라서 본 논문에서는 주변환경의 변화에 강인한 복합 센서단말을 통해, 하천 정보(유량, 유속, 수위 등)을 실시간 측정하고, 해당지역의 특성을 고려한 하천 또는 저지대의 위험도를 스스로 판단할 수 있는 기술을 제안한다. 또한, 본 논문에서는 제안한 저비용 초소형의 단말 장치로 지점의 하천 정보를 실시간 측정하여 IoT망을 통해 3차원 하천 디지털트윈 모델로 전달하여, 유속과 수위를 그대로 재연함으로써, 하천 침수 위험 감시의 효율성을 검증하였다. 3차원 DEM(Digital Elevation Models) 데이터와 실제 하천을 관측한 데이터를 이용한 디지털트윈 검증 결과, 데이터 전송 지연시간을 감안하여 3초 이내에 하천의 수위와 유속이 3차원 모델에 반영되는 것을 확인하였다. 이 결과로부터 열악한 환경에서도 실시간 하천 상황을 원거리에서 모니터링 할 수 있으며, 강우와 유출에 따른 하천 홍수 메카니즘을 새롭게 시뮬레이션할 수 있는 방법론을 제시할 수 있을 것으로 기대한다.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.22 no.6
• /
• pp.31-36
• /
• 2022

In this paper, we present the design, manufacture and test results of Backend unit for SAR(Synthetic Aperture Radar) that can be applied on a small satellite. The Backend unit for SAR was designed with a control/storage board, TRX(transmission and receiving) board and a power supply board as a single unit in consideration of the applying of a small satellite. The control/storage board uses RFSoC to generate wideband chirp signal, generate operating timings, and perform control and calculations for SAR operation. The TRX board is designed to convert the wideband chirp signal generated by the control/storage board to the operating frequency of X-band by up-converting the frequency. Since small size, light weight, and low cost are important consideration for small satellite, MIL/Industrial grade components were appropriately applied and the at the same time it was designed to ensure mission life through the radiation test, analysis and space environment tests.

• Journal of the Institute of Convergence Signal Processing
• /
• v.16 no.3
• /
• pp.90-95
• /
• 2015

This study presents a method to test quite small-sized and light-weighted micro-drill bits which are used to make holes in printed circuit boards(PCB). After getting images of micro-drill bits through the high resolution microscope, we developed image processing algorithms to detect fiducial points, and then measured diverse factors of the drill-bit based on these points. We also developed the window-based inspection system to automatically discriminate normal and abnormal status. For the relative comparison of its performance, the system was compared with an existing inspection system using test images. Experimental results showed that the proposed system slightly improved performance, and also classified correctly some misjudged errors which were occurred in the existing system.

• Journal of the Microelectronics and Packaging Society
• /
• v.10 no.1
• /
• pp.19-24
• /
• 2003

A very small size 2.4 GHz ISM band BPF(Band Pass Filter) is realized using LTCC Multi-layer technology. Proposed design method enables to achieve BPF size $2.0\times1.2\times0.8mm^3$. A $lambda/4$ resonator with shunt-to-ground loaded capacitor is used to shorten resonator length, achieving higher quality factor. Also this resonator enables BPF to improve out-of-band rejection. Coupling coefficients between coupled strip-line resonators and external quality factor (Qe) of a resonator are derived and applied to the filter design. The measured results show good agreement with simulated data.

• Korean Journal of Optics and Photonics
• /
• v.17 no.4
• /
• pp.354-358
• /
• 2006

A silicon lens and an insulator of pyrex, components of a micro-electron column, should be assembled by aligning and stacking simultaneously. An optical alignment of a diffraction beam and a laser welding were employed for the assembly of a source lens and an Einzel lens with precision within $\pm$4% for the maximum aperture size. The experimental condition for optical alignment and laser welding are explained. Anodic bonding was used to assist in stacking lenses. A micro-electron column of smaller apertures assembled with precise alignment and fabrication was tested with a current image of a Cu grid of 9$\mu$m in linewidth, and showed a higher resolution in acceleration mode.

• Aerospace Engineering and Technology
• /
• v.9 no.2
• /
• pp.98-104
• /
• 2010

The moisture in the atmosphere exerts a lot of influence upon Gas turbine engine performances. There is a noticeable influence of wet air at the summer sea level, high flight mach number and low engine rpm increasingly. An altitude Engine Test Facility is used to accomplish the engine performance tests at dry air condition and wet air condition, through which engine performance results is revealed. Also, Gas turbine Simulation Program is used to predict the variation of engine performance due to inlet humidity. In the result, net thrust and specific fuel consumption measured -2.826% and 1.325%, respectively at wet air condition compared to dry air condition.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.05a
• /
• pp.137-142
• /
• 2002

The fluid mechanics and operating conditions of gas-lubricated proceeding bearings in micro rotating machinery such as micro polarization modulator and micro gas turbine are different from their larger size ones. Due to non-continuum effects, there is a slip of gas at the walls. Thus in this paper, the slip flow effect is considered to estimate the pressure distribution and load-carrying capacity of micro gas-lubricated proceeding bearings as the local Knudsen number at the minimum film thickness is greater than 0.01. Based on the compressible Reynolds equation with slip flow, the static characteristics of micro gas-lubricated proceeding bearings are obtained. Numerical predictions compare the pressure distribution and load capacity considering slip flow with the performance of micro proceeding bearings without slip f]ow for a range of bearing numbers and eccentricities. The results clearly show that the slip flow effect on the static characteristics is considerable and becomes more significant as temperature increases.

• Transactions of Materials Processing
• /
• v.18 no.7
• /
• pp.544-549
• /
• 2009

This study aimed to elucidate the deformation mechanism during low-temperature superplasticity of fine-grained Ti-6Al-2Sn-4Zr-2Mo-0.1Si alloy in the context of constitutive equation. For this purpose, initial coarse equiaxed microstructure was refined to $2.2{\mu}m$ via dynamic globularization. Globularized microstructure exhibited large superplastic elongations(434-826%) at temperatures of $650-750^{\circ}C$ and strain rate of $10^{-4}s^{-1}$. It was found that the main deformation mechanism of fine-grained material was grain boundary sliding accommodated by dislocation motion with both stress exponent (n) and grain size exponent (p) values of 2. When the alpha grain size, not sub-grain size, was considered to be an effective grain size, the apparent activation energy for low-temperature superplasticity of the present alloy(169kJ/mol) was closed to that of Ti-6Al-4V alloy(160kJ/mol).

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.9 no.1
• /
• pp.23-28
• /
• 2008

Due to the modem MEMS technologies, the electron lenses that are used in the microcolumn can have much smaller optical aberrations compared with conventional electron lenses for the bulky electron columns. Since the electron lens system have great effect on the performance of the microcolumn, it is important to study the dependence of image quality on the configuration of the electronic imaging system, among which the source-lens part is most sensitive. In this work, we investigated the electron beam characteristics according to the shapes of extractor and limiting aperture that are elements of the source-lens part. By analyzing the data obtained, we proposed the optimum configuration of the electron lens system.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.10
• /
• pp.875-883
• /
• 2007

The objective of this research was to develop a coaxial rotor MAV which is suitable for a indoor reconnaissance mission. Preliminary design parameters were determined, based on the dimensions of other reference MAVs. The designed rotor performance was estimated by Blade Element Momentum Theory, and the analyses were compared against the measurements. Stability and vibration issues of the prototype were circumvented by making parts of vehicle with NC machine, as well as equipped with teetering rotor and stabilizer. The designed coaxial rotor MAV showed successfully flight equipped with video camera. However, it was founded that further research activities should be focused on efficient rotor design to obtain better performance.