• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.12 s.103
• /
• pp.1171-1178
• /
• 2005

Multi-code code division multiple access(MC-CDMA) has been proposed for providing the various service rates with different quality of service requirement by assigning multiple codes and increasing the capacity. However, it suffers from the serious problem of high peak to average power ratio(PAPR). So, it requires large input back-off, which causes poor power consumption in high power amplifier(HPA). In this paper, we propose a new method that can reduce PAPR efficiently by constraint codes based on the opposite correlation to the incoming information data in MC-CDMA. PAPR reduction depends on the length and indices of constraint codes in MC-CDMA system. There is a trade-off between PAPR reduction and the length of constraint codes. From the simulation results, we also investigate the BER improvement in AWGN channel with HPA. The simulation results show that BER performance can be similar with linear amplifier in two cases: 1) Using exact constraint codes without input back-off and 2) a few constraint codes with small input back-off.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.9 no.6
• /
• pp.136-150
• /
• 2010

Due to the effect of indoor coverage problem, the QoS of the indoor users will be degraded dramatically, with the number of indoor users. The femto cell is a popular solution for such problems. Since the price of the femto base station is usually cheap enough, one can sets up huge number of base stations in a small indoor area to reduce the size of communication cell. In this way, the QoS of the indoor users can be improved significantly. Moreover, the data rate can also be increased. However, how to decide an ideal transmitting power according to the surrounding radio environment is not a trivial problem, that still has not been addressed well. If the transmit power of femto base station is too large, the interference to the macro users will be increased. Conversely, if the transmit power of femto base station is too small; the coverage of femto base station will be reduced. To address this problem, we propose a power configuration method in femto base station using Genetic Algorithm by investigating a new fitness function. Furthermore, we adopt the weighted sum approach to improve the user performance in different modes. The simulation results show that the proposed power configuration method can not only improves the downlink SINR, but also enhance the channel capacity for both the Macro cell systems and Femto cell systems compared with some conventional methods.

• Journal of Biomedical Engineering Research
• /
• v.19 no.3
• /
• pp.251-260
• /
• 1998

The Holter monitoring system is a widely used noninvasive diagnostic tool for ambulatory patient who may be at risk from latent life-threatening cardiac abnormalities. In this paper, we design a high performance intelligent holter monitoring system which is characterized by the small-sized and the low-power consumption. The system hardware consists of one-chip microcontroller(68HC11E9), ECG preprocessing circuit, and flash memory card. ECG preprocessing circuit is made of ECG preamplifier with gain of 250, 500 and 1000, the bandpass filter with bandwidth of 0.05-100Hz, the auto-balancing circuit and the saturation-calibrating circuit to eliminate baseline wandering, ECG signal sampled at 240 samples/sec is converted to the digital signal. We use a linear recursive filter and preprocessing algorithm to detect the ECG parameters which are QRS complex, and Q-R-T points, ST-level, HR, QT interval. The long-term acquired ECG signals and diagnostic parameters are compressed by the MFan(Modified Fan) and the delta modulation method. To easily interface with the PC based analyzer program which is operated in DOS and Windows, the compressed data, that are compatible to FFS(flash file system) format, are stored at the flash memory card with SBF(symmetric block format).

• Journal of Ginseng Research
• /
• v.31 no.2
• /
• pp.79-85
• /
• 2007

Compound K (CK) is a final metabolite of panaxadiol ginsenosides. Although panax ginseng is known to have anti-diabetic activity, the active ingredient is not yet fully identified. Therefore, it would be interesting to know whether and how CK has an anti-diabetic activity. First, insulin secretion-stimulating activity of CK was examined using RIN-m5F cell line and primary cultured islets. CK enhanced the insulin secretion in a concentration dependent manner. This effect, however, was almost completely abolished in the presence of diazoxide, $K^+$ channel opener, indicating that the insulin secretion-stimulating activity of CK is presumably due to blockade of ATP sensitive $K^+$ channel. In addition, effects of CK on gene expressions of hepatic enzymes (phosphoenolpyruvate carboxykinase[PEPCK], glucose-6-phos-phatase[G6Pase]) and on adipocyte differentiation in H4IIE and 3T3-Ll cells, respectively, were examined. CK suppressed the induction of PEPCK and G6Pase mRNA expressions under the dexamethasone/cAMP stimulation condition. CK also reduced the $PPAR-{\gamma}$ mRNA expression and triglyceride accumulation in a dose dependent manner as compared to the control. The present study suggests that CK deserves to examine whether it shows an anti-diabetic activity in animal and human studies.

• Journal of the Institute of Electronics Engineers of Korea CI
• /
• v.38 no.6
• /
• pp.106-112
• /
• 2001

Unfortunately, the area without economical efficiency, especially the far distance sea, is much lower than that of a urban area-built-up area. It should be promoted the equivalent level to a urban area in the light of future-oriented universal service. Actually, Because propagation environment of mobile communication in the sea is greatly different from that for inland focused on built-up area, a propagation prediction model in the sea should be distinguished from inland-based one. Accordingly, the purpose of this study is to suggest the propagation prediction model for the sea service as a method to minimize unnecessary facilities investment and maintenance caused by additional or new building of a base station. If mobile phone service for far distance sea is provided by expanding limited communication zone of narrow band CDMA mobile communication whose spread band FA is 1.2288MHz. Suggested propagation prediction model includes five parameters to minimize facilities investment of a base station and maximize channel capacity: equivalent line of sight, chip delay by PN code, antenna altitude, power of base station and gain of antennas. Finally, suggested propagation prediction model is simulated and, the results are examined for its utility by comparing with loss of free space.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.7
• /
• pp.18-25
• /
• 2014

To increase wireless capacity, the concurrent use of multiple wireless interfaces on different frequency bands, called aggregation, can be considered. In this paper, we focus on aggregation of multiple Wi-Fi interfaces with packet-level traffic spreading between the interfaces. Two aggregation schemes, link bonding and multipath TCP (MPTCP), are tested and compared in a dualband Wi-Fi radio system with their Linux implementation. Various test conditions such as traffic types, network delay, locations, interface failures and configuration parameters are considered. Experimental results show that aggregation increases throughput performance significantly over the use of a single interface. Link bonding achieves lower throughput than MPTCP due to duplicate TCP acknowledgements (ACKs) resulting from packet reordering and filtering such duplicate ACKs out is considered as a possible solution. However, link bonding is fast responsive to links' status changes such as a link failure. It is shown that different combinations of interface weights for packet spread in link bonding result in different throughput performance, envisioning a spatio-temporal adaptation of the weights. We also develop a mathematical model of power consumption and compare the power efficiency of the schemes applying different power consumption profiles.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.6A
• /
• pp.555-567
• /
• 2010

Unlike single-hop systems, multi-hop systems that use relay nodes assign a part of the overall resources to relay communications. If efficient resource allocation schemes are not adopted, this leads to a loss of resources. Moreover, because we may not be able to guarantee high-link performance due to the adjacent-cell interference in relay-based cellular systems, resource efficiency can be severely decreased. In this paper, we propose efficient resource allocation schemes for downlink relay-based networks in 3GPP (3rd Generation Partnership Project) LTE (Long Term Evolution)-Advanced systems. Unlike conventional schemes that have static resource regions for each data link, the proposed schemes dynamically allocate the resources of each link to resource blocks, by considering the channel state and the capacity of each link. We also propose resource overlapping schemes in which two different links overlap at the same resource region, so as to improve cell or user throughput performance. The proposed resource overlapping schemes do not require additional processes such as interference cancellation in users, thank to considering additional interference from resource overlapping in advance.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.4
• /
• pp.62-70
• /
• 2015

Recently the demand for projected capacitance touch screens is sharply growing especially for large screens for medical devices, PC monitors and TVs. Large touch screens in general need a controller of higher complexity. They usually have a larger number of driving and sensing lines, and hence it takes longer to scan one frame for touch detection leading to a low frame scan rate. In this paper, a novel touch screen control technique is presented, which scans each frame in two steps of simultaneous multi-channel driving. The first step is to drive all driving lines simultaneously and determine which sensing lines have any touch. The second step is to sequentially rescan only the touched sensing lines, and determine exact positions of the touches. This technique can substantially increase the frame scan rate. This technique has been implemented using an FPGA and an AFE board, and tested using a commercial 23-inch touch screen panel. Experimental results show that the proposed technique improves the frame scan rate by 8.4 times for the 23-inch touch screen panel over conventional methods.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.18 no.6
• /
• pp.169-180
• /
• 2018

White light-emitting diodes (LEDs) are more economical than fluorescent lights, and provide high brightness, a high lifetime expectancy, and greater durability. As LEDs are closely connected with people's daily lives, dimming control of LED is an important component in providing energy savings and improving quality of life. In visible light communications systems using these LEDs, multiple input multiple output (MIMO) technology has attracted a lot of attention, in that it can attain the channel capacity in proportion to the number of antennas. This paper analyzes the power performance of three kinds of modulation in visible light communications (VLC) systems applied space-time block code (STBC) techniques. The modulation schemes are return-to-zero on-off keying (RZ-OOK), variable pulse position modulation (VPPM), and overlapping pulse position modulation (OPPM), and dimming control was applied. The power requirements and power consumption were used as metrics to compare the power efficiency in $2{\times}2$ STBC-VLC environments under the three kinds of modulation. We confirm that dimming control affects the communications performance of each modulation scheme. VPPM showed greater consumption among the three modulations, and OPPM showed energy savings comparable to VPPM.

• Journal of Broadcast Engineering
• /
• v.16 no.1
• /
• pp.23-32
• /
• 2011

Design and Implementation of Clipcast Service via Terrestrial DMB This paper outlines the system design and the implementation process of clipcast service that can send clips of video, mp3, text, images, etc. to terrestrial DMB terminals. To provide clipcast service in terrestrial DMB, a separate data channel needs to be allocated and this requires changes in the existing bandwidth allocation. Clipcast contents can be sent after midnight at around 3 to 4 AM, when terrestrial DMB viewship is low. If the video service bit rate is lowered to 352 Kbps and the TPEG service band is fully used, then 320 Kbps bit rate can be allocated to clipcast. To enable clipcast service, the terminals' DMB program must be executed, and this can be done through SMS and EPG. Clipcast service applies MOT protocol to transmit multimedia objects, and transmits twice in carousel format for stable transmission of files. Therefore, 72Mbyte data can be transmitted in one hour, which corresponds to about 20 minutes of full motion video service at 500Kbps data rate. When running the clip transmitted through terrestrial DMB data channel, information regarding the length of each clip is received through communication with the CMS(Content Management Server), then error-free files are displayed. The clips can be provided to the users as preview contents of the complete VOD contents. In order to use the complete content, the user needs to access the URL allocated for that specific content and download the content by completing a billing process. This paper suggests the design and implementation of terrestrial DMB system to provide clipcast service, which enables file download services as provided in MediaFLO, DVB-H, and the other mobile broadcasting systems. Unlike the other mobile broadcasting systems, the proposed system applies more reliable SMS method to activate the DMB terminals for highly stable clipcast service. This allows hybrid, i.e, both SMS and EPG activations of terminals for clipcast services.