• Journal of the Society of Naval Architects of Korea
• /
• v.38 no.3
• /
• pp.93-106
• /
• 2001

T-joint and hopper knuckle joint models are typical welded joints in ship structure, which are very susceptible to fatigue damage under service condition. Fatigue test and fracture mechanical analysis were performed on these joints to find out characteristics of fatigue behavior. Unified S-N curve was developed from the test results of these two types of joint using hot spot stress concept, and also propagation life was also estimated using Paris' crack propagation law. Residual stress effect on propagation life was considered in calculating propagation life, as was done with thermo-elasto-plastic FE analysis and residual stress intensity factor calculation. Fatigue life of similar kinds of welded joint could be predicted with this unified S-N curve and fracture mechanical analysis technique.

• The Journal of Korean Academy of Prosthodontics
• /
• v.32 no.1
• /
• pp.120-147
• /
• 1994

This study was performed for the purpose of evaluating the stress distribution around threaded type implants, cylindrical type implants and teeth connected with rigid or non-rigid connector. The stress distribution around the surrounding bone was analyzed by three-dimensional photoelastic method. Twelve mandibular photoelastic epoxy resin models and a circular polariscope were used to record the isochromatic fringes. After the stress distribution around the implant and tooth was observed, the results were as follows ; 1. In threaded type implants, stress concentrated patterns were observed at the neck either vertical or 25 degree lateral force. 2. The stress concentrated patterns were observed at the tooth apical portion and neck portions of the implant and tooth when a threaded implant was connected with the tooth by either a rigid or non-rigid connector. More force was generated at the tooth neck portion by a rigid connector and more force at the implant neck portion by a non-rigid connector. 3. The stress concentrated patterns were observed at the apical portion of the implant and tooth when a cylindrical type ,implant was connected with the tooth either by a rigid or non-rigid connector. More force was generated at the tooth apical portion by a rigid connector and more force at the neck portion of the tooth and implant by a non-rigid connector. 4. The stress around the tooth was more equally distributed in a threaded type implant than in a cylindrical implant when the tooth was connected with either a rigid or non-rigid connector. 5. The stress around a threaded type implant was progressively more equally distributed in the following order : 1) when used a single implant, 2) a non-rigid connection with the implant and tooth, 3) a rigid connection with the implant and tooth, 4) a rigid connection with two implant fixtures.

• Journal of the KSME
• /
• v.34 no.11
• /
• pp.830-835
• /
• 1994

화재에 의해 손상을 입은 압력용기에 대해 유한요소법을 이용하여 응력해석을 수행하여 아래와 같은 결론을 얻었다. (1) 응력해석 결과, 압력용기의 자중, 열응력 및 바람의 영향은 내부압력에 비해 무시할 수 있을 정도로 미미하였다. (2) 기하학적 형상변화가 발생한 손상용기의 손상 부위에서의 부식 전\ulcorner후에서의 안전계수는 각각 3.5와 2.1로 손상이 없는 단순용기의 6.3과 4.6보다 상당히 작음을 알 수 있었다. 따라서, 손상 부위에서의 적절한 보강이 이루어져야 할 것이다. (3) 원형 링과 수직 보조대로 보강된 보강용기 모형의 등가 응력값은 상당히 감소되어 화재로 발생한 기하학적 형상 변화에 따른 응력 집중을 줄일 수 있었다. 앞서 정의된 안전계수를 이용 하면 부식 전의 안전계수는 5.3, 부식 후는 3.8 이상으로 증가하였다. (4) 안전계수는 운전 중의 부식 진행과 더불어 두께에 반비례하여 감소하므로, 운전중 부식의 진행을 억제 또는 최소화할 수 있는 방법이 강구되어야 하겠다. (5) 복구방안으로 본 연구에서 해석된 보강책을 채택하는 경우, 작업시 보조대 주위에서의 잔류 응력이 발생되지 않도록 특히 유의해야 하며, 복구 작업 후 철저한 시험검사(비파괴 검사, 스트 레인 측정)가 수반되어야 할 것으로 사료된다.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.1 no.1
• /
• pp.189-200
• /
• 1998

본 연구에서는 얇은 마레이징강으로 제작된 천마 연소관에 브라켓이 용접되어 비행 날개를 볼트로 체결한 경우, 압력과 공력하중에 의해 브라켓 부위에 집중되는 응력의 해석기법을 정립하기 위하여 선형해석과 기하학적 비선형 해석을 수행하였다. 높은 압력에 의해 발생한 얇은 연소관의 면내 응력이 구조물의 강성을 증가시키는 응력의 강성보강효과(stress stiffening effect)를 고려한 기하학적 비선형 해석을 수행하여 선형해석 결과와 비교하였으며, 압력과 공력하중을 동시에 적용할 수 있는 복합하중시험기로 변형률을 측정하여 해석치의 정확성을 검토하였다. 얇은 연소관에 압력과 공력하중이 동시에 작용하는 경우는 응력의 강성보강효과를 고려한 기하학적 비선형 해석을 수행함으로써 보다 정확한 응력을 구할 수 있다는 결론을 얻었다.

• Journal of Welding and Joining
• /
• v.7 no.1
• /
• pp.17-27
• /
• 1989

용접에 이와 같이 발생하는 용접잔류응력과 변형은 용접구조물의 제작시 여러 가지 장해를 유발 할 뿐만 아니고 그 구조물의 사용중에 있어서도 파괴의 발생 또는 파괴의 전파에 직.간접적으로 기여하여 악영향을 끼치게 된다. 용접잔류응력은 용접구조물의 피로감도를 저하시키거나, 취성균 열 및 응력부식균열의 진전을 용이하게 하며 용접변형은 구조물의 외관을 해치거나 국부적으로 스트레인집중을 초래하여 이 역시 취성파괴의 원인으로 작용하여 구조물의 파괴사고를 유발할 위험성을 내포하고 있다. 따라서 용접변형과 잔류응력을 극도화하기 위한 대책은 용접기술자로 서 용접시공시 유의해야 할 가장 큰 사항의 하나라고 할 수 있다. 보고에서는 이러한 용접변형 과 잔류응력현상에 대해 그 발생기구를 금속학적 측면에서 고찰하고 그 경감대책에 대해서는 구 조물의 형상이나 종류에 따라 각각별개의 대책이 수립되어야 하나 여기서는 보편적인 경우에 한 해 해설하고저 한다.

• The Journal of Korean Academy of Prosthodontics
• /
• v.48 no.3
• /
• pp.181-188
• /
• 2010

Purpose: The purpose of this study was to compare the stress distribution characteristics of four different abutment connections on SS-$III^{(R)}$ fixture under occlusal loading, using 3-dimensional finite element method. Materials and methods: The fixture of SS-$III^{(R)}$ (Osstem, Korea) with 4 mm diameter and 11.5 mm length and 4 types of abutments were analyzed; Solid, Com-Octa, ComOcta Gold, and Octa abutment. The models were placed in the area of first molar in the mandible. The 4 loading conditions were; (1) the vertical loading of 100 N on the central fossa, (2) the vertical loading of 100 N on the buccal cusp, (3) the $30^{\circ}$ inclined loading of 100 N to lingual side on the central fossa, and (4) the $30^{\circ}$ inclined loading of 100 N to the lingual side on the buccal cusp. The 3G.Author program was used, the von-Mises stress was calculated and the stress contours were plotted on each part of the implant systems and the surrounding bone structures. Results: Regardless of abutment types and loading conditions, higher stress concentration was observed at the cortical bone. In cancellous bone, the highest stress was observed at apical portion and the maximum stress occurred at the implant neck. The higher internal stress was observed in the fixtures than in the bone. The lowest stress was observed at loading condition 1 and the stress concentration was also lower than any other loading conditions. Conclusion: Within the limitation of the result of this study, it seems that the abutment connection type does not affect much on the stress distribution of bone structure.

• Journal of the Korea Convergence Society
• /
• v.8 no.4
• /
• pp.189-197
• /
• 2017

In the design of an automotive structural component, one of the more important tasks for a design engineer is to determine the life of the component and to ensure that the component will not fail prematurely. In order to accomplish this, a design engineer will first use simple section analysis to come up with a section shape in the concept design stage and use more advanced analysis for stress level. At this stage, the analysis should focus on understanding overall behavior in terms of load paths and gross stress levels. A model that is adequate for a stiffness analysis of the structure will usually provide an adequate level of stress information in the design process. To perform a detailed stress analysis, the structure models must have the detailed local areas such as stress concentrations or force(or displacement) distributions. This paper is to present the design considerations for the stress analysis of automotive structure.

• Journal of the Korean Society for Railway
• /
• v.10 no.5
• /
• pp.546-553
• /
• 2007

The objective of the present paper is to evaluate the effect of the evolution of contact surface profile by fretting wear on the contact stress distribution and fatigue crack initiation site of press-fitted shaft by means of an analytical method based on experimental data. A finite element analysis was performed to analyze the stress states of press-fitted shaft, considering the worn contact surface profiles of shaft. The evolutions of contact stress as wearing of contact surface were analyzed by finite element analysis and fatigue crack nucleation sites were evaluated by fretting fatigue damage parameter (FFDP) md multiaxial fatigue criteria. It is found that the stress concentration of a contact edge in press-fitted sha손 decreases rapidly at the initial stage of total fatigue life, and its location shifts from the contact edge to the inside due to fretting wear as increasing of fatigue cycles. Thus the transition of crack nucleation position in press-fitted shaft is mainly caused by stress change of a contact edge due to the evolution of contact surface profile by fretting wear. Therefore, it is suggested that the nucleation of multiple cracks on fretted surface of press fits is strongly related to the evolution of surface profile at the initial stage of total fatigue life.

• Nuclear Engineering and Technology
• /
• v.10 no.2
• /
• pp.65-72
• /
• 1978

In this paper, it is attempted to investigate the phenomena of iodine stress corrosion cracking of Zircaloy-4 cladding failures in reactor through the results of similar out-of-pile test in iodine vapour. The main result of this experiment is a finding of the relation between the threshold stress which can lead to iodine stress corrosion cracking of Zircaloy-4 tube and the iodine concentration. The values of critical stress and the critical iodine concentration are also obtained. A model which relates failure time of Zircaley-4 tube to failure stress and iodine concentration is suggested as follows: log t$_{F}$ =5.5-(3/2)log$_{c}$-4log $\sigma$ where t$_{F}$ : failure time, minutes c: iodne concentration, mg/㎤ $\sigma$: stress, 10$^4$psi.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.20 no.1
• /
• pp.37-42
• /
• 1984

This paper deals with the characterics of the stability of uncontinuous plate structures with cracks. The relation between the J-intergal of the cracks existing in the stress-concentrated regions and local strain are investigated experimentally and theoretically. The BEM(boundary element method)analysis and test results lead to the follow conclusions: 1. A non-dimensional J was computed in a plate stress and strain condition for several kind of loads and crack types. The J design curves are defined as follows: J sub(E)/$\sigma$ sub(y) super(2) a=3.345(e/e sub(y) ) super(2) at e/e sub(y)$\leq$1 J sub(E)/$\sigma$ sub(y) super(2) a=3.345(e/e sub(y) ) at e/e sub(y)$\geq$1 2. Use of this curve provides a good estimation for the uncontinuous plate structures with cracks existing in the stress and strain concentrated region. 3. The stability of the characteristics is mainly depenent upon not the length of cracks but the type of the cracks.