• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.33-33
• /
• 2003

• Proceedings of the KIEE Conference
• /
• 2006.07d
• /
• pp.1791-1792
• /
• 2006

이 논문에서는 저속 회전체의 불균일 질량측정을 위한 새로운 신호처리 방법을 제안하고 이를 이용한 자동차 타이어의 보정(balancing) 방법에 관해 설명한다. 타이어를 포함한 시스템의 동력학 모델을 기반으로 타이어의 불균일 질량에 의해 발생되는 진동과 이로 인해 로드셀에 작용하는 힘의 관계식을 유도하고, 센서의 측정계수(scale factor)를 포함한 매개변수를 실험 데이터로부터 계산한다. 또한, 기존 방법과 달리 불균일 질량의 크기와 위치를 정확하고 효율적으로 측정할 수 있는 방법을 소형 마이크로 프로세서를 이용하여 구현하고 실험을 통해 그 성능을 검증한다.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.4
• /
• pp.39-45
• /
• 1995

본 논문은 복수 집중질량을 갖고 제어 종동력을 받는 자유 Timoshenko보의 동적 안정성에 관한 것으로, 비행중의 미사일이나 로켓의 연료탱크, Payload등의 기계장치부를 복수의 집중질량으로 간주하여 이러한 항공우주 구조물들이 추진력인 종동력을 받을때에 대한 계의 동적 안정성을 판별한다. 수학적 모델에 대한 운동방정식은 확장된 해밀톤 원리를 이용한 유한요소법에 의해 유도되며, 복수 부가질량의 위치 및 크기변화, 센서의 위치 및 게인(gain)의 변화에 따른 계의 안정성 지도(stability maps)를 보여준다. 또한 보의 전단 변형이나 회전관성의 효과 뿐만아니라, 추질력의 방향이 제어되는 경우와 제어되지 않는 경우에 대한 최대 추진력 값이 수치 시뮬레이션을 통해 예측된다.

• 대한공업교육학회지
• /
• v.32 no.2
• /
• pp.171-187
• /
• 2007

The purpose of this study is to measure the lathe tool vibration and verify its usefulness using the fiber optic interferometeric sensor instead of using common accelerometer. To compare two vibration signals a Fabry-Perot fiber optic sensor(FOS) is directly attached to the left-side surface of the lathe tool and an accelerometer is attached near to the fiber optic sensor. Measurement signals from the FOS and theoretical results of receptance simulation are compared. When the amplitude of tool vibration increased the frequency shift phenomena was occurred. This means that mass effect occurred and vibration spectrum moved to the low frequency region. Generally this results is agreement to the regenerative chatter. The chatter frequency is not same as the natural frequency of the tool itself. The FOS can also applied to laboratory experiments for students. This experimental technique is perhaps the first attempts because of directly attachment technique. Therefore, suggested Fabry-Perot fiber optic sensor can be used to monitoring the tool wear and vibration.

• Proceedings of the Acoustical Society of Korea Conference
• /
• spring
• /
• pp.319-322
• /
• 2004

본 연구에서는 DNA의 상보적인 결합을 이용하여 DNA 혼성화 반응을 감지할 수 있는 SH형 SAW 센서를 개발하였다. 측정에 사용된 DNA는 15개의 염기를 가진 올리고 뉴클레오티드를 사용하였으며 이에 대해 상보적 결합이 가능한 염기서열을 가진 것과 그렇지 않은 미스매치 형태의 DNA 올리고뉴클레오티드를 이용하여 DNA 혼성화 반응 특성을 측정하였다. SH형 SAW 센서는 압전 단결정 $LiTaO_{3}$를 사용하여 100 MHz 발진되는 형태로 제작하였으며, 센서의 지연선 위에 Ti/Au 층을 증착하여 SH기가 수식된 탐침 DNA의 고정화가 가능하게 하였다. 제작된 센서는 Au가 증착된 박막위에 탐침 DNA를 SAM 방법으로 고정화 시켰을 경우와 고정화된 탐침 DNA와 표적 DNA와의 혼성화 반응을 시키고 난 후의 센서의 주파수 변화를 각각 측정하였다. 개발된 DNA 혼성화 반응 측정용 SH형 SAW센서는 DNA 혼성화 특성에 기인한 질량하중 효과에 따른 안정적인 주파수 변화를 나타내었다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.31 no.10
• /
• pp.876-883
• /
• 2007

Numerical simulations are conducted for the design of a micro thermal mass air flow sensor (MAFS), which consists of a microfabricated heater and thermopiles on the silicon-nitride ($Si_3N_4$) thin membrane structure. It is important to find the proper locations of these thermal elements in the design of MAFS with improved sensitivity. Three heating modes of the micro-heater are considered: constant temperature, constant power and heating pulses. The analyses are focused on the membrane temperature profile near the sensing section. Considered are the practical flow velocities, ranging from 3 m/s to 35 m/s, and the corresponding Reynolds numbers from 1000 to 10000. The results show that one of optimum sensing locations is about $100{\mu}m$ away from the microheater. It is concluded that the heating mode and configurations of thermal elements are the main factors for the MAFS with higher sensitivity.

• The Journal of the Acoustical Society of Korea
• /
• v.42 no.3
• /
• pp.233-242
• /
• 2023

In this paper, the effect of mass injection on the control of tip vortex cavitation was studied experimentally. A mass injection system for a 3D hydrofoil was designed to control the location of injection as well as the injection rate. A series of cavitation tests were carried out in a cavitation tunnel for different injection locations and rates. The cavitation behaviour was observed using a high-speed camera and the corresponding noise was measured using a hydrophone installed in the observation window. The results showed that the tip vortex cavitation was suppressed under certain conditions and the noise was reduced in some frequency bands. It was also found that there is a location where the effect of mass injection could be maximized and hence the noise reduction.

• Analytical Science and Technology
• /
• v.18 no.6
• /
• pp.483-490
• /
• 2005

Mass resolution of the time of flight aerosol mass spectrometer for an aerosol component analysis depends on the initial direction and the initial energy of the ions. We have found that the shape of the optimum post focusing electric field is not linear. The maximum electric potential should be applied to the ions whose initial direction is 90 degree. To check on the post focusing effects, we have installed a laser ablation mass spectrometer. By using this LA-MS, we have found that the average energy distribution of the laser ablated ions is 8 eV. To establish the optimum mass resolution, a time delay and a high voltage are needed, and the results of the study show that 1500 nsec, and 3.7 kV are the optimum parameters for our system respectively. The isotope mass signals of copper show a good resolution.

• Korean Journal of Optics and Photonics
• /
• v.13 no.1
• /
• pp.9-14
• /
• 2002

A surface plasmon sensor has been fabricated for detection of concentration and refractive-index of a mixed solution. Based on the Kretschmann-Raether attenuated-total-reflection configuration, the sensor consists of 54 nm-thick Ag metal layer under a prism and a cell containing the mixed solution. We have observed a nonlinear refractive-index change as the ethanol-water concentration increased. The experimental results show us that the detection limit of the SPR sensor is 3$\times$10$^{-2}$ % in ethanol mass ratio. The concentration-to-index curve shows a linear increase in the range of ethanol concentration from 0% to 50%, but a nonlinearity is observed beyond 50%. We have modeled the nonlinearity and compared it with the experimental results.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.04a
• /
• pp.83-84
• /
• 2014