• Proceedings of the KSR Conference
• /
• 2004.06a
• /
• pp.994-1000
• /
• 2004

대형시험장비가 설치되는 실험실의 계획에서 장비의 진동은 간과할 수 없는 고려사항이다. 따라서 시험장비를 지지하는 구조물과 기초의 설계시 시험장비의 운행 중 발생하는 공진을 피할 수 있는 구조적 체계의 진동특성에 대한 적절한 평가가 요구된다. 본 논문은 동적특성을 얻기 위해 바닥구조물의 FE 모델링에 관하여 기술하였다. 또한 진동저감을 위한 시험장비기초의 설계를 위해 tuning, 진동기준. 방진시스템을 검토하였다. 시험장비의 진동을 줄이는 최선의 방법은 low tuning 이였으며 이의 구현을 위해 방진스프링과 함께 단단한 콘크리트 블록위에 시험장비를 설치하였다. 총체적인 방진시스템의 구조적 진동특성은 이동성, 힘, 속도 스펙트라를 이용해 표현되었다. 전달과 지점이동 FRF의 비를 시뮬레이션을 통해 비교함으로서 바닥 슬래브의 진동전달 정도가 관찰되었다.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.10 no.1
• /
• pp.139-148
• /
• 2006

The dynamic characteristics of a bridge deduced by using the modeling techniques depend on its stiffness and mass calculated from its geometric model. This research develops the FE modeling techniques for a steel plate girder bridge with composite section. and proves their validity by comparing the results with those from actual measurement. The FE modeling techniques are divided into two categories--a simplified one and two-dimensional model and a detailed three-dimensional model. In the meantime, the dynamic responses of the bridge tested for this research were measured by the ambient vibration some of accelerometers were been attached to its upper slab girder under normal traffic load. The Cross Power Spectrum obtained from the measurement was used to analyze the dynamic characteristics by natural excitation techniques. The analytic results are compared to those of each FE modeling, and thereby the modeling techniques were proved to be valid.

• The Journal of the Acoustical Society of Korea
• /
• v.31 no.3
• /
• pp.142-150
• /
• 2012

The waveguide finite element (WFE) method is a useful numerical technique to investigate wave propagation along waveguide structures which have uniform cross-sections along the length direction ('x' direction). In the present paper, the vibration and radiated noise of the submerged pipe with fluid is investigated numerically by coupling waveguide finite elements and wavenumber boundary elements. The pipe and internal fluid are modelled with waveguide finite elements and the external fluid with wavenumber boundary elements which are fully coupled. In order to examine this model, the point mobility, dispersion curves and radiated power are calculated and compared for several different coupling conditions between the pipe and internal/external fluids.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.565-573
• /
• 2007

This paper is concerned with the dynamic modeling, active vibration controller design and experiments for a cylindrical shell equipped with MFC actuators. The dynamic model was derived by using Rayleigh-Ritz method based on Donnel-Mushtari shell theory. The actuator and sensors for the MFC actuator equations were derived based on pin-force model. The equations of motion were then reduced to modal equations of motion by considering the modes of interest. The sensor equations were also converted to a reduced form. An aluminum shell was fabricated to demonstrate the effectiveness of modeling and control techniques. The boundary conditions at both ends of the shell were assumed to be shear diaphragm. Theoretical natural frequencies were calculated and compared to experimental result. It was observed that the theoretical result is in good agreement with experimental result for the first two modes. The multi-input and multi-output positive position feedback controller, which can cope with first two modes, was then designed based on the blockinverse theory and implemented using DSP. It was found from experiment that vibrations can be successfully suppressed.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.18 no.4
• /
• pp.465-472
• /
• 2008

An automotive windshield wiper system is modeled mainly for vibration analysis purpose. The model is composed of solid links, ideal joints, imperfect joints to simulate unavoidable manufacturing defects and bushings having stiffness, contact between a wiper blade and a wind screen glass, friction, a spring and an actuator. Main stream of wiper dynamics analysis has been obtaining a closed form of system of equations using Newton's or Lagrange's formula and doing a numerical simulation study to understand and predict the behavior of it. However, the modeling process is complex since a wiper system is of multibody and a contact problem occurs. When imperfection, such as dead zone of a joint and stiffness of a rubber bushing, should be included, the added complexity makes the modeling difficult. Since the imperfection is understood as main cause of problematic vibration, the dynamics model of a wiper system aiming vibration analysis should include such unavoidable manufacturing defects in the model. An open form of dynamic model of a automotive windshield wiper system with imperfect joints using a commercial software is obtained and a simulation analyssis is conducted for vibration reduction study.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.6
• /
• pp.3435-3441
• /
• 2014

A dynamic modeling and prediction of polyurethane foam material, which is used as the seat in vehicles is very important for improving the ride quality of vehicle occupants. In this study, parameters to define the nonlinear stiffness and time-variant characteristics of the viscoelasticity of polyurethane foam were obtained using a static compression test. Polynomial functions and convolution integral were used to model the nonlinear and viscoelastic characteristics of polyurethane foam mathematically. The dynamic behaviors excited by the seat floor displacement were analyzed using a numerical integration method for the nonlinear vibration model. As a result, the viscoelastic characteristics of polyurethane foam was found to be an important parameter for improving the ride quality.

• Journal of the Korean Society for Railway
• /
• v.18 no.3
• /
• pp.194-202
• /
• 2015

In this paper, dynamic modeling with viscoelastic properties of a human body resting on a seat is presented to quantitatively analyze ride quality of passengers exposed to vertical vibrations. In describing the motions of a seated body, a 5 degree-of-freedom multibody model from the literature is investigated. The viscoelastic characteristics of seats used in railway vehicles are mathematically formulated with nonlinear stiffness characteristics and convolution integrals representing time delay terms. Transfer functions for the floor input are investigated and it is found that these are different in accordance with the input magnitude due to nonlinear characteristics of the seat. Measured floor input at the railway vehicle is used to analyze realistic human vibration characteristics. Frequency weighted RMS acceleration values are calculated and the effects of the seat design parameters on the frequency weighted RMS acceleration values are presented.

• Journal of the Korean Society for Railway
• /
• v.16 no.2
• /
• pp.85-92
• /
• 2013

An important source of noise from railways is rolling noise caused by wheel and rail vibrations induced by acoustic roughness at the wheel-rail contact. The main contributors to rolling noise are the sleepers, rail, and wheels. In order to analyze and predict rolling noise, it is necessary to understand the vibrating behaviors of railway tracks, as well as of the wheels. In the present paper, theoretical modeling methods for railway track are reviewed in terms of rolling noise; these methods are applied for the three representative types of domestic railway tracks operated: the conventional ballasted track, KTX ballasted track and KTX concrete track. The characteristics of waves propagating along rails are investigated and compared among the types of tracks. The tracks are modeled as discretely supported Timoshenko beams and are compared in terms of the averaged squared amplitude of velocity, which is directly related to the sound radiation from the rails.

• Computational Structural Engineering
• /
• v.5 no.3
• /
• pp.139-146
• /
• 1992

Vibrational behaviors of highway girder bridges due to heavy traffics are discussed, and empirical formulae for impact factors are suggested in this paper. Appropriate vehicle model for vibration analysis is found and impact factors are calculated with different surface roughnesses, vehicle speeds and span lengths. It is shown that the present codes tend to underestimate impact factors.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.05c
• /
• pp.458-463
• /
• 1996

수송용기가 운반 트레일러에 의해 정상수송될 때, 국내 도로 상태에서 발생되는 반복적인 진동 흑은 충격하중을 측정하기 위해 국도 및 고속도로에서 차량수송시 가속도량를 기록하였으며, 이 측정결과를 주파수분석기로 분석하여 전산진동해석을 위한 입력자료를 생산하였다. 수송용기의 기계구조에 대한 건전성을 평가하기 위한 전산해석은 ABAQUS 코드로 KSC-7 수송용기를 3차원 보요소로 모델링하여 응력평가를 수행하였다.