• Korean Journal of Environmental Agriculture
• /
• v.26 no.1
• /
• pp.69-76
• /
• 2007

The accumulation curves of phenol in the flesh of apples were measured at $5^{\circ}C$, $25^{\circ}C$ and $40^{\circ}C$ when they were exposed to phenol vapor, The effective diffusivities of phenol at the rind and flesh were determined by comparing its experimentally obtained accumulation curves with simulated ones. The simulation was carried out by the non-steady state diffusion rate equation. The diffusion model assumed the consecutive diffusion of phenol at the rind and flesh of apples. The detection time of phenol in the flesh of apples was shortened with increasing temperature, and it accumulated amount also increased rapidly. The estimated effective diffusivity of phenol at the rind of apples increased with temperature as like $1.1{\times}10^{-13}\;m^2/s$ at $5^{\circ}C$, $1.4{\times}10^{-13}\;m^2/s$ at $25^{\circ}C$ and $2.2{\times}10^{-13}\;m^2/s$ at $40^{\circ}C$, but those at the flesh of apples were invariant as $1.5{\times}10^{-10}\;m^2/s$ at this temperature range. The effect of temperature on the diffusivity of phenol was small, but the increase of the vapor pressure of phenol with temperature accelerated the penetration of phenol at the rind, resulting in the rapid accumulation at the flesh of apple.

• Economic and Environmental Geology
• /
• v.35 no.3
• /
• pp.221-227
• /
• 2002

Column experiments were performed to evaluate the removal efficiency of soil vapor extraction (SVE) iota TCE (trichloroethylene) and toluene in soil. Homogeneous Ottawa sands and real soils collected from contaminated area were used to investigate the effect of soil properties and SVE operation conditions on the removal efficiency. In column teats with two different sizes of Ottawa sand, the maximum effluent TCE concentration in a coarse sand column was 442 mg/L and 337 mg/L in a fine sand column. However, after 20 liter gas flushing, the effluent concentrations were very similar and more than 90% of initial TCE mass were removed from the column. For two real contaminated soil columns, the maximum effluent concentration decreased 50% compared with that in the homogeneous Ottawa coarse sand column, but 99% of initial TCE mass were extracted from the column within 40 liter air flushing, suggesting that SVE is very available to remove volatile NAPLs in the contaminated soil. To investigate the effect of contaminant existing time on the removal efficiency, an Ottawa sand column was left stable for one week after TCE was injected and the gas extraction was applied into the column. Its effluent concentration trend was very similar to those for other Ottawa sand columns except that the residual TCE after the air flushing showed relatively high. Column tests with different water contents were performed and results showed high removal efficiency even in a high water content sand column. Toluene as one of BTEX compounds was used in an Ottawa sand column and a real soil column. Removal trends were similar to those in TCE contaminated columns and more than 98% of initial toluene mass were removed with SVE in both column.

• Korean Journal of Medicinal Crop Science
• /
• v.10 no.3
• /
• pp.200-205
• /
• 2002

Platycodin D was isolated from n-butanol extract of Platycodi radix(Platycodon grandiflorum and identified by the spectroscopic analysis using $^1H$ and $^{13}C$ NMR techniques. A new method of analysis of platycodin D by high performance liquid chromatography(HPLC) was established using a reversed phase system with YMC-Pack ODS-AM( 250 X 4.6 mm) column and 30% acetonitrile as a mobile phase. Evaporative light scattering detector was used as detector. The kinds of extraction solvents and methods were examined to determine the efficient extraction condition and HPLC analysis was carried out to establish the optimum drying condition for the root of Platycodon grandiflorum. The contents of Platycodin D was highest as 0.083% when platycodon roots were dried at $60^{\circ}C$ using dry oven.

• Analytical Science and Technology
• /
• v.10 no.1
• /
• pp.1-8
• /
• 1997

We identified nicotine, cotinine and toluene in high school volunteer's urine by using GC/NPD, GC/FID and GC/MS. To analyze of nicotine and cotinine, urine samples were extracted with diethylether and centrifuged on a benchtop centrifuge for 5 min. The upper organic layer was injected into a GC. The distributions of nicotine and cotinine were $4{\sim}630{\mu}g/L$ and $63{\sim}1,602{\mu}g/L$ in smoking-group, respectively. To analyze of toluene, head space vial was filled with 2mL sodium citrate solution and 1mL of urine. The vial was warmed in a water bath at $55^{\circ}C$ for 20min, and then $250{\mu}L$ of head space air was injected into a GC. The result show that toluene was not detected in all of the volunteers' samples. However, the range of toluene was 0.1~28.0mg/L in glue sniffer's urine samples(NISI data).

• Parasites, Hosts and Diseases
• /
• v.29 no.2
• /
• pp.139-148
• /
• 1991

Cryptosporidium, a coccidian protozoa, commonly causes a self-limiting diarrheal illness in humans and animals. Fecal samples from various animals in Chonbuk district were observed using Sheather's aoatation technique, Kinyoun's modified acid-fast staining, and osmic acid pre-fixed Giemsa staining. The oocysts were detected in 74 cages(29.6%) out of 250 cages of mature mice, 26 (13.3%) out of 195 mature house rats, 75 (15.0%) out of 4-week-old 500 fowls, 98(19.9%) out of 6 to 8-month-old 500 pigs, and 111(22,2%) out of 2 to 5-year-old 500 dairy cattle, respectively. The degree of prevalence was slight in general, but actual prevalence was higher than infection rate because the detection rates were higher in repeated-preparation examinations in comparison to the first examination. Meanwhile, large and small types of oocysts were detected from mice, house rats, pigs, and cattle, and midium type from fowls.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.35S no.2
• /
• pp.137-145
• /
• 1998

In this paper, we propose a tube-hole center detection vision algorithm verifying the position of a tele-controlled robot and providing visual information for increasing reliability and efficiency in the diagnosis of steam generator (SG) tubes in nuclear power plant. A tele-controlled robot plays a role in carrying the probe used in inspecting the integrity of SG tubes. Thus accurately locating a tele-controlled robot on the desired tube-hole center is important issue for reliability of inspection. To do this work, we have to find the tube-hole center locations from the input image. At first, we apply the three-class segmentation method modified for this application. WE extract minimum bounding rectangles (MBRs) in the theresholded binary image. Second, for discriminating between MBR by tube and MBR by noise, we introduce the MBR rejection rules as knowledge-based rule set. MBRs are divided into the very dark region MBRs and the very bright region MBRs. In order to describe the region of complete tube-hole, the MBRs need a process of pairing each other. We then can find the tube-hole center from the paired MBR. For more accurately finding the tube-hole center in several sequential images, the centers of some frames need to be averaged. We tested the performance of our method using hundreds of real images.

• Journal of Sensor Science and Technology
• /
• v.3 no.1
• /
• pp.32-39
• /
• 1994

Catalytic combustion type sensor was fabricated for alcohol detection, and its characteristics were tested. When the resistance of Pt coil for pellistor is 2.0 ohm, suggestible input power to bridge circuit was about 300 mW for methanol detection, and in the range from 350 mW to 400 mW for ethanol. Pellistors were prepared by means of impregnating Pt or Pd on the ${\gamma}$-alumina bead for sensing element, and transition metals such as $Co_{3}O_{4}$, $Fe_{2}O_{3}$ for compensating element.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.2
• /
• pp.245-249
• /
• 2007

In this paper describes image enhancement technique using deconvolution processing for ultrasonic nondestructive testing. When flaws are detected fur B-scan or C-scan, blurring effect which is caused by the moving intervals of transducer degrades the quality of images. In addition, acquisited images suffer form speckle noise which is caused by the ultrasonic components reflected from the grain boundary of material (1,2). The deconvolution technique can restore sharp peak value or clean image from blurring signal or image. This processing is applied to C-scan image obtained from known specimen. Experimental results show that the deconvolution processing contributes to get improved the quality of C-scan images.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.16 no.3
• /
• pp.331-337
• /
• 2018

The decommissioning of nuclear power plants is generally executed in five steps, including preparation, decontamination, cutting/demolition, waste disposal and environmental restoration. So, for efficient decommissioning of nuclear power plants, worker safety, effects compared to cost, minimization of waste, possibility of reuse, etc., shall be considered. Worker safety and measurement technology shall be secured to exert optimal efficiency of nuclear power plant decommissioning work, for which accurate measurement technology for systems and devices is necessary. Typical In-Situ methods for decommissioning of nuclear plants are CZT, Gamma Camera and ISOCS. This study used ISOCS, which can be applied during the decommissioning of a nuclear power plant site without collecting representative samples, to take measurements of the S/G Water Chamber. To validate the measurement values, Microshield and the GEANT4 code was used as the actual method were used for modeling, respectively. The comparison showed a difference of $1.0{\times}10^1Bq$, which indicates that it will be possible to reduce errors due to the influence of radiation in the natural environment and the precision of modeling. Based on the research results of this paper, accuracy and reliability of measurement values will be analyzed and the applicability of the direct measurement method during the decommissioning of NPPs will be assessed.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.36 no.6
• /
• pp.504-509
• /
• 2016

Defects in dissimilar metal welds are reported to be on the increase during the operating lifespan and aging of nuclear power plants. In Korea, reported cases of defects due to dissimilar metal welds include the drain nozzle of a steam generator and RCS hot tube sampling nozzles. Therefore, there is an urgent need to develop a reliable automated nondestructive inspection technique and a system for the inspection of dissimilar metal welds of small diameter nozzles in a high radiation area of a nuclear power plant. In this study, to ensure effective defect inspection of small diameter nozzles (RCS high-temperature tube sampling nozzle) of a nuclear power plant, three different methods were developed. These include: (1) optimum inspection probe design by beam simulation, (2) multi-directions UT optimum inspection technique for the inspection of small diameters of different welded parts, and (3) remote control automatic inspection system. The developed technique and systems have been verified to be suitable for use in the inspection of defects in smaller diameter nozzles in nuclear power plants.