• Journal of the Korean Vacuum Society
• /
• v.21 no.1
• /
• pp.29-35
• /
• 2012

The Hydrogenated silicon nitride (SiNx:H) using plasma enhanced chemical vapor deposition is widely used in photovoltaic industry as an antireflection coating and passivation layer. In the high temperature firing process, the $SiN_x:H$ film should not change the properties for its use as high quality surface layer in crystalline silicon solar cells. Initially PECVD-$SiN_x:H$ film trends were investigated by varying the deposition parameters (temperature, electrode gap, RF power, gas flow rate etc.) to optimize the process parameter conditions. Then by varying gas ratios ($NH_3/SiH_4$), the hydrogenated silicon nitride films were analyzed for its optical, electrical, chemical and surface passivation properties. The $SiN_x:H$ films of refractive indices 1.90~2.20 were obtained. The film deposited with the gas ratio of 3.6 (Refractive index=1.98) showed the best properties in after firing process condition. The single crystalline silicon solar cells fabricated according to optimized gas ratio (R=3.6) condition on large area substrate of size $156{\times}156mm$ (Pseudo square) was found to have the conversion efficiency as high as 17.2%. Optimized hydrogenated silicon nitride surface layer and high efficiency crystalline silicon solar cells fabrication sequence has also been explained in this study.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2000.05a
• /
• pp.410-418
• /
• 2000

In general, the experienced diver go into the water to find out Pan Shell which is spontaneously generated and brought up at the depth of 25-30 meters in the slime along the bank of an inlet of western and southern sea. However, this searching system has caused some problems in terms of economical efficiency and riskiness of diver. To overcome such problems and enhance the competence capability of fishermen, a new Pan Shell searching system is required. If an onboard searching system as a substitute of the way of diving into the deep water to identify the existence of Pan Shell is developed, it would be greatly beneficial to fishermen. The purpose of this research is to develop a new searching system of Pan Shell by making use of 50-200 Khz Ultra Sonic Signal, A/D Converter and computer process program. Based on the fact that Sonic Signal between the soft part of slime and the hard part of sand, pebble and Pan Shell is different, the possibility of this system have been approved in some degree by this time of research. However, to utilize this new system, further research on the establishment of data base and sample data is required. With the theoretical knowledge, the systematic research on the searching capability of Ultra Sonic Signal will be continued to identify the influence against the sea water subject. In this research, signal will be analyzed according to the influence range, power and sensitiveness of Ultra Sonic Generator. In addition, the radius of Ultra Sonic Signal will be included. The experimental field work will be executed at Nockdong, Pulkyo and other places well known as a habitat of Pan Shell.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.05a
• /
• pp.951-953
• /
• 2015

Learning for thinking says the behavior of the organism changes as a result of practice or experience. It is very difficult to identify focusing ability objectively when students study. But, brain of the body is not so. EEG signal means continuously electric records of brain potential variation between two points on the scalp when brain activities take place. In types of EEG, there are delta(0~4Hz), theta(4~8Hz), alpha(8~13Hz), beta(13~30Hz) and gamma waves(30~50Hz). SMR waves and Mid-beta waves appear when focused for studying. Part for the most influence on concentrating reported that Mid-beta waves. In relation to brain activities, EEG has been actively researched for evaluating brain focus index system during learning and study. So, By using Biopac system for this study, measured brain wave was converted into FFT for extracting Mid-beta domain signals that are related to learning after giving focus invoked subjects to a small number of people. When concentrating, we measured the change in the power of the Mid-beta frequency domain and presented a correlation. Based on these results, we analyzed whether students are concentrated objectively on learning or not. and hope to offer more efficient learning method.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.10A
• /
• pp.922-929
• /
• 2005

This paper proposes an adaptive pilot beacon equipment for mobile communication systems based on direct spread spectrum technology which generates the pilot channel for handoff between base stations by using the information acquired from the downstream wireless signal regarding the overhead channel information. Such an adaptive pilot beacon equipment will enable low power operation since among the wireless signals, only the pilot channel will be generated and transmitted. The pilot channel in the downstream link of the CDMA receiver is used to acquire time and frequency synchronization and this is used to calibrate the offset for the beacon, which implies that time synchronization using GPS is not required and any location where forward receive signal can be received can be used as the installation site. The downstream link pilot signal searching within the CDMA receiver is performed by FPGA and DSP. The FPGA is used to perform the initial synchronization for the pilot searcher and DSP is used to perform the offset correction between beacon clock and base station clock. The CDMA transmitter the adaptive pilot beacon equipment will use the timing offset information in the pilot channel acquired from the CDMA receiver and generate the downstream link pilot signal synchronized to the base station. The intermediate frequency signal is passed through the FIR filter and subsequently upconverted and amplified before being radiated through the antenna.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.304-304
• /
• 2010

최근 생활에 편리하며 휴대하기 좋은 전자기기들이 개발되고 있다. 휴대폰이나 MP3와 같은 전자기기들은 거의 필수품이라고 할 정도로 우리의 일상생활에 근접하여 있다. 그 종 대표적으로 휴대폰의 종류로 스마트폰과 같은 터치스크린을 이용한 사례는 점차 상승하고 있으며 시간이 지날수록 그 수요는 더욱 많아지고 있다. 때문에 몰입감 제공을 위하여 햅틱장치의 채용이 일반화 되고 있다. 햅틱장치란 가상환경이나 원거리에 있는 환경과 사용자가 상호 작용할 때 사용자에게 촉감이나 힘의 정보를 전달하여 주는 장치로 진동 및 회동 저항에 의해 사용자로 하여금 촉감들 느낄 수 있도록 하는 장치를 뜻한다. 즉, 현실감을 전달을 중점으로 하는 햅틱장치는 빠른 응답 속도와, 진동의 주파수와 크기는 독립적으로 제어가 가능해야 하며 기계적 수용기들을 직접적으로 자극할 수 있어야 한다. 하지만 모바일 햅틱장치의 경우 크기 및 소비전력의 문제로 모든 스펙을 만족하기에는 어려워 좀 더 한정적인 느낌을 제공할 수 없다. 현재까지 모바일 장치에서 햅틱 피드백을 위하여 진동모터나, 솔레노이드, 압전 액츄에이터 등이 많이 사용되어 지고 있다. 그 중 압전 액츄에이터는 입력에너지를 기계적 출력에너지로 변환되는 효과를 이용 한 것으로 압력 센서, 초음파 센서 등 많은 분야에서 응용되고 있으며 변위 범위는 작지만, 크기가 매우 작고 변위 정밀도가 높으며 발생력과 응답속도가 빠르다는 장점이 존재한다. 이를 이용한 햅틱 압전 엑츄에이터의 제작에 사용되는 압전 세라믹스는 높은 전기적 특성을 가질수록 더 졸은 효율을 가지며 이로 인하여 보다 좋은 전기적 특성을 가지는 압전 세라믹스를 필요로 한다. 현재 많이 사용되는 PZT계 세라믹스는 우수한 전기적 특성으로 많이 사용되고 있지만 Pb의 유독성으로 인한 환경문제로 Pb가 포함된 제품을 제한하고 있어 현재 Lead-free의 연구가 이루어지고 있다. Lead-free중 Ba$(Ti_{0.8}Zr_{0.2})O_3$(BZT)는 PZT계 세라믹스를 대체할 차세대 압전 재료로 주목받고 있다. 일반적으로 Lead-free의 압전계수($d_{33}$=100~300pC/N)는 비교적 낮은 값을 보이지만 BZT의 압전계수(BZT $d_{33}$~620pC/N)는 PZT계 세라믹스의 압전계수($d_{33}$=500~600pC/N)와 비교하여 부족하지 않은 압전계수를 보여주며 PZT를 대체할 재료로 주목받고 있다. 본 실험은 햅틱 압전 엑츄에이터용 무연 압전세라믹스의 제작을 위하여 Ba$(Ti_{0.8}Zr_{0.2})O_3-(Ba_{0.7}Ca_{0.3})-TiO_3$(BZT -BCT)의 조성으로 유전 및 압전 특성을 조사하였다.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.2
• /
• pp.93-100
• /
• 2009

This paper presents a step up four channel DC-DC converter using charge pump voltage doubler structure. Our goal is to design and implement DC-DC converter for capacitive SP4T RF MEMS switch in front end module in wireless transceiver system. Charge pump structure is small and consume low power 3.3V input voltage is boosted by DC-DC Converter to $11.3{\pm}0.1V$, $12.4{\pm}0.1V$, $14.1{\pm}0.2V$ output voltage With 10MHz switching frequency. By using voltage level shifter structure, output of DC-DC converter is selected by 3.3V four channel selection signals and transferred to capacitive MEMS devices. External passive devices are not used for driving DC-DC converter. The total chip area is $2.8{\times}2.1mm^2$ including pads and the power consumption is 7.52mW, 7.82mW, 8.61mW.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.12
• /
• pp.141-146
• /
• 2016

HEVC/H.265 is the latest joint video coding standard proposed by ITU-T SG 16 WP and ISO/IEC JTC 1/SC29/WG 11. In H.265, pictures are divided into a sequence of coding tree units(CTUs), and the CTU further is partitioned into multiple CUs to adapt to various local characteristics. Its coding efficiency is approximately two times high compared to previous standard H.264/AVC. However according to the size of extended CU(coding unit) and transform block, the hardware size of PMR(prediction/mode decision/reconstruction) block within video encoder is about 4 times larger than previous standard. In this study, we propose a new less complex hardware architecture of PMR block which has the most high complexity within encoder without any noticeable PSNR loss. Using this simplified block, we can shrink the overall size the H.265 encoder. For FHD image, it operates at clocking frequency of 300 MHz and frame rate of 60 fps. And also for the test image, the Bjøntegaard Delta (BD) bit rate increase about average 30 % in PMR prediction block, and the total estimated gate count of PMR block is around 1.8 M.

• Progress in Medical Physics
• /
• v.9 no.1
• /
• pp.47-53
• /
• 1998

Nuclear Medicine Images have comparatively poor spatial resolution, making it difficult to relate the functional information which they contain to precise anatomical structures. Anatomical structures useful in the interpretation of SPECT /PET Images were radiolabelled. PET/SPECT Images Provide functional information, whereas MRI mainly demonstrate morphology and anatomical. Fusion or Image Registration improves the information obtained by correlating images from various modalities. Brain Scan were studied on one or more occations using MRI and SPECT. The data were aligned using a point pair methods and surface matching. SPECT and MR Images was tested using a three dimensional water fillable Hoffman Brain Phantom with small marker and PET and MR Image was tested using a patient data. Registration of SPECT and MR Images is feasible and allows more accurate anatomic assessment of sites of abnormal uptake in radiolabeled studies. Point based registration was accurate and easily implemented three dimensional registration of multimodality data set for fusion of clinical anatomic and functional imaging modalities. Accuracy of a surface matching algorithm and homologous feature pair matching for three dimensional image registration of Single Photon Emission Computed Tomography Emission Computed Tomography (SPECT), Positron Emission Tomography (PET) and Magnetic Resonance Images(MRD was tested using a three dimensional water fill able brain phantom and Patients data. Transformation parameter for translation and scaling were determined by homologous feature point pair to match each SPECT and PET scan with MR images.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.18 no.6
• /
• pp.642-653
• /
• 2008

This study deals with modeling of head-related transfer functions(HRTFs) using principal components analysis(PCA) in the time and frequency domains. Four PCA models based on head-related impulse responses(HRIRs), complex-valued HRTFs, augmented HRTFs, and log-magnitudes of HRTFs are investigated. The objective of this study is to compare modeling performances of the PCA models in the least-squares sense and to show the theoretical relationship between the PCA models. In terms of the number of principal components needed for modeling, the PCA model based on HRIR or augmented HRTFs showed more efficient modeling performance than the PCA model based on complex-valued HRTFs. The PCA model based on HRIRs in the time domain and that based on augmented HRTFs in the frequency domain are shown to be theoretically equivalent. Modeling performance of the PCA model based on log-magnitudes of HRTFs cannot be compared with that of other PCA models because the PCA model deals with log-scaled magnitude components only, whereas the other PCA models consider both magnitude and phase components in linear scale.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.12
• /
• pp.80-87
• /
• 2013

A novel instrumentation amplifier(IA) using positive polarity current-conveyor(CCII+) for electronic measurement systems with low cost, wideband, and gain control with wide range is designed. The IA consists of two CCII+, three resistor, and an operational amplifier(op-amp). The principal of the operating is that the difference of two input voltages applied into two CCII+ used voltage and current follower converts into same currents, and then these current drive resistor of (+) terminal and feedback resistor of op-amp to obtain output voltage. To verify operating principal of the IA, we designed the CCII+ and used commercial op-amp LF356. Simulation results show that voltage follower used CCII+ has offset voltage of 0.21mV at linear range of ${\pm}$4V. The IA had wide gain range from -20dB to 60dB by variation of only one resistor and -3dB frequency for the gain of 60dB was 400kHz. The IA also has merits without matching of external resistor and controllable offset voltage using the other resistor. The power dissipation of the IA is 130mW at supply voltage of ${\pm}$5V.