• The KIPS Transactions:PartC
• /
• v.14C no.5
• /
• pp.431-438
• /
• 2007

RFID system is core technology that construct ubiquitous environment for replacement of barcode technology. Use ratio of RFID system rapidly increase because the technology has many good points such as identification speed, storage space, convenience etc. But low-cost tag operates easily by query of reader, so the system happened user privacy violent problem by tag information exposure. The system studied many ways for security application, but operation capability of low-cost tag is about $5K{\sim}10K$ gates, but only $250{\sim}3K$ gates allocated security part. So it is difficult to apply security to the system. Therefore, this scheme uses dividing 64 bits and reduces arithmetic, so proposed scheme provide mutual authentication that can apply to low-cost RFID system. Existing methods divide by 4 and used 96 bits. However, that reduces 32 bits length for lightweight and reduced from communication number of times of 7 times to 5 times. Also, because offer security by random number than existing scheme that generate two random numbers, that is more efficient. However, uses hash function for integrity that was not offered by XOR arithmetic and added extension of proposed scheme. Extended scheme is not offered efficiency than methods that use XOR arithmetic, but identification distance is mode that is proposed secure so that can use in for RFID system.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.22 no.6
• /
• pp.114-122
• /
• 2018

This study presents the emergency assessment method about seismic safety of cable-supported bridges using seismic acceleration sensors installed on the primary structural elements of them. The structural models of bridges are updated iteratively to make their dynamic characteristics to be similar to those of real bridges based on the comparison of their natural frequencies with those of real bridges estimated from acceleration data measured at ordinary times by the seismic acceleration sensor. The displacement at the location of each seismic acceleration sensor is derived by seismic analysis using design earthquake, and the peak value of them is determined as the disaster management criteria in advance. The displacement time history is calculated by the double integration of the acceleration time history which is recorded at each seismic acceleration sensor and filtered by high cut(low pass) and low cut(high pass) filters. Finally, the seismic safety is evaluated by the comparison of the peak value in calculated displacement time history with the disaster management criteria determined in advance. The applicability of proposed methodology is verified by performing the seismic safety assessment of 12 cable-supported bridges using the acceleration data recorded during Gyeongju earthquake.

• Journal of Sensor Science and Technology
• /
• v.6 no.5
• /
• pp.385-391
• /
• 1997

An objection of this study is to develop a measuring circuit of a gauge using radioisotope for compaction control. The gauge developed in this study makes use of radioisotope with the activity exempted from domestic atomic law and consists of measuring circuits for gamma-rays and thermal neutrons, a high voltage supply unit, and a microprocessor. To obtain meaningful numbers of pulse counts, parallel five and two circuits are provided for gamma-rays and thermal neutrons, respectively. Being simple in electrical characteristics of G-M detector for gamma-rays, pulses are counted through only a shaping circuit. Very small pulses generated from He- 3 proportional detector for thermal neutrons are amplified to the maximum of 50 [dB] and a window comparator accepts only pulses with meaning. To minimize effects of natural environmental radiation and electrical noise, circuits are electrostatically shielded and pulses made by ripples are eliminated by taking frequency of high voltage supplied to the circuit and pulse height of ripples into consideration. One-chip microprocessor is applied to process various counts, results are stored and the gauage is made capable to communicate with PC. Enough and meaningful numbers of pulses are counted with the prototype gauage for compaction control.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.20 no.6
• /
• pp.523-531
• /
• 2008

In hole type CPTu equipment which combines the concepts of inhole test method and piezocone test method was newly developed in order to evaluate the dynamic properties of marine soils. It is possible to perform inhole type CPTu without any additional source device because the source and receiver are contained inside the cone rod, which is different from the conventional seismic cone system. In this study, laboratory tests using kaolinite as soft soil and numerical simulations using finite element method were carried out to investigate the effects of several parameters including test methods and soil conditions on the test results from inhole type CPTu and to find out the optimum test method. It was found that it is necessary to maintain the length of swing arm as well as the distance between source and receiver consistently to obtain the rigorous test results. The laboratory test and numerical results also reveal that contrary to the input wave frequency, the water content of soil layer and the disturbance due to the installation of swing arm apparently affect the shear wave velocity.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.10 no.4
• /
• pp.187-192
• /
• 2007

Impact on cylindrical surface caused by plunging breaking waves is investigated experimentally. The breaking waves are generated in a wave flume by decreasing the wave maker frequencies linearly and focusing the generated wave components at one specific location. The breaking wave packets are based on constant wave steepness spectrum. Three inclination angles of cylinder are applied to examine the effect of contact angle between cylinder and front surface of breaking waves. Also, the effect of cylinder diameter on pressure distribution and its peak value is investigated by adopting three cylinders with different diameters. The longitudinal location of cylinder is slightly moved in eight different points to find out a probable maximum value of impact pressure. The pressures and total force on cylinder surface are measured by piezo-electric pressure sensors and 3-components load cell with 30kHz sampling rate. The variation of peak impact pressures and forces is analyzed in terms of cylinder diameter, inclination angle and location. Also, the pressure distribution on cylindrical surface is examined. The cylinder location and surface position are more important parameters that govern the magnitude and shape of peak pressures, while the cylinder diameter and inclined angle are relatively insignificant. In a certain conditions, the impact phenomenon becomes very unstable which results in a large variation of measured valves in repeated runs.

• Journal of Dairy Science and Biotechnology
• /
• v.35 no.4
• /
• pp.244-248
• /
• 2017

The effects of ultrasonic (1.2~1.7 kJ/g TS) pretreatment on the solubilization of dairy and livestock sludge were separately evaluated to investigate the possibility of recycling dairy sludge as a potential source of organic carbon. Compared to other industrial wastewater and sewage sludge, dairy sludge has higher organic matter content and no toxic materials. The solubilization rates of dairy and livestock sludge, at a specific energy input of 1.7 kJ/g TS, were 14.5% and 10.6%, respectively. After the 90-minute ultrasonic treatment, the soluble COD (chemical oxygen demand) increased about 7.1 times that of the initial SCOD, at an increase rate of $0.022m^{-1}$. In comparison, the increase in soluble nitrogen, which was ~3.4 times that of the initial soluble nitrogen concentration, was much smaller than the increase in SCOD; thus, the C/N ratio increased from 4.0 to 8.7.

• Archives of design research
• /
• v.17 no.1
• /
• pp.25-36
• /
• 2004

The purpose of this study is to analyse and interpret the way of differentiated expression and changing creative trend following 5-day workweek which has been recently adopted. For this aim 11 pieces of distinctive advertising text were analysed. The criteria for selection of analysing text were relativeness with 5-day workweek and cognitive inconsistency. These texts were negative phrases, exaggerated expression, and excessively humorous appeals. The study revealed the followings: First, 5-day workweek concerned advertising texts were considered as high attention getting and successful in stimulating advertising audiences' curiosity by using the elements opposing the value and belief system formed in the existing audience. Second, consumption-driving lifestyle was found in most expressions for credit cards advertising. Third, hedonic need-oriented lifestyle was typical in young consumer products category. Fourth, family centered lifestyle emphasized meaning of rest and solidarity of family.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.46 no.9
• /
• pp.712-722
• /
• 2018

This paper conducts parametric studies on flapping wing design, one of the most important design parameters of insect-mimicking aerial vehicles. Experimental study on wing shape was done through comparison and analysis of thrust, pitching moment, power consumption, and thrust-to-power ratio. A two-axis balance and hall sensor measure force and moment, and flapping frequency, respectively. Wing configuration is biplane configuration which can develop clap and fling effect. A reference wing shape is a simplified dragonfly's wing and studies on aspect ratio and wing area were implemented. As a result, thrust, pitching moment, and power consumption tend to increase as aspect ratio and area increase. Also, it is found that the flapping mechanism was not normally operated when the main wing has an aspect ratio or area more than each certain value. Finally, the wing shape is determined by comparing thrust-to-power ratio of all wings satisfying the required minimum thrust. However, the stability is not secured due to moment generated by disaccord between thrust line and center of gravity. To cope with this, aerodynamic dampers are used at the top and bottom of the fuselage; then, indoor flight test was attempted for indirect performance verification of the parametric study of the main wing.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.13 no.5
• /
• pp.359-369
• /
• 2020

In this paper, we proposed a charge pump (CP) circuit that has a wide operating range while reducing the current mismatch for the PLL that generates the main clock of the CMOS X-Ray detector. The operating range and current mismatch of the CP circuit are determined by the characteristics of the current source circuit for the CP circuit. The proposed CP circuit is implemented with a wide operating current mirror bias circuit to secure a wide operating range and a cascode structure with a large output resistance to reduce current mismatch. The proposed wide operating range cascode CP circuit was fabricated as a chip using a 350nm CMOS process, and current matching characteristics were measured using a source measurement unit. At this time, the power supply voltage was 3.3 V and the CP circuit current ICP = 100 ㎂. The operating range of the proposed CP circuit is △VO_Swing=2.7V, and the maximum current mismatch is 5.15 % and the maximum current deviation is 2.64 %. The proposed CP circuit has low current mismatch characteristics and can cope with a wide frequency range, so it can be applied to systems requiring various clock speed.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.5
• /
• pp.601-611
• /
• 2016

The research, development and use of seismic isolation systems have been increasing with the gradual development of structure safety assurance methods for earthquakes. The High Damping Rubber Bearing (HDRB), one type of seismic isolation system, is a Laminated Rubber Bearing using special High Damping Rubber. However, as its damping function is slightly lower than that of the Lead Rubber Bearing, a similar seismic isolation system, its utilization has not been high. However, the HDRB has a superior damping force to the Natural Rubber Bearing, which has similar materials and shapes, and the existing Lead Rubber Bearing has a maleficence problem in that it contains lead. Thus, studies on HDRBs that do not use lead have increased. In this study, a test targeting the HDRB was done to examine its various dependence properties, such as its compressive stress, frequency and repeated loading. To evaluate the HDRB's seismic performance in response to several earthquake waves, the shaking table test was performed and the results analyzed. The test used the downscaled bridge model and the HDRB was divided into seismic and non-seismic isolation. Consequently, when the HDRB was applied, the damping effect was higher in the non-seismic case. However, its responses on weak foundations, such as in Mexico City, represented increased shapes. Thus, its seismic isolator.