DOI QR코드

DOI QR Code

A Study on Isolation Performance of High Damping Rubber Bearing Through Shaking Table Test and Analysis

진동대 실험 및 해석을 통한 고감쇠 고무받침의 면진성능 연구

  • Kim, Hu-Seung (Department of Civil Engineering, University of Seoul) ;
  • Oh, Ju (Korean Intellectual Property Office)
  • Received : 2016.03.11
  • Accepted : 2016.05.12
  • Published : 2016.05.31

Abstract

The research, development and use of seismic isolation systems have been increasing with the gradual development of structure safety assurance methods for earthquakes. The High Damping Rubber Bearing (HDRB), one type of seismic isolation system, is a Laminated Rubber Bearing using special High Damping Rubber. However, as its damping function is slightly lower than that of the Lead Rubber Bearing, a similar seismic isolation system, its utilization has not been high. However, the HDRB has a superior damping force to the Natural Rubber Bearing, which has similar materials and shapes, and the existing Lead Rubber Bearing has a maleficence problem in that it contains lead. Thus, studies on HDRBs that do not use lead have increased. In this study, a test targeting the HDRB was done to examine its various dependence properties, such as its compressive stress, frequency and repeated loading. To evaluate the HDRB's seismic performance in response to several earthquake waves, the shaking table test was performed and the results analyzed. The test used the downscaled bridge model and the HDRB was divided into seismic and non-seismic isolation. Consequently, when the HDRB was applied, the damping effect was higher in the non-seismic case. However, its responses on weak foundations, such as in Mexico City, represented increased shapes. Thus, its seismic isolator.

최근 빈번하게 발생하는 크고 작은 지진에 대비하여 구조물의 지진에 대한 안전성을 확보하기 위한 방안으로 지진격리시스템을 이용한 연구개발과 사용이 점차 증가하고 있다. 지진격리시스템의 하나인 고감쇠 고무받침(HDRB)는 특수한 고감쇠 고무(HDR)를 이용한 적층형 고무받침으로서 유사 지진격리장치인 납 고무받침에 비해 감쇠기능이 다소 떨어지는 단점이 있어 활용도가 높지 않았다. 그러나, 고감쇠 고무받침은 재료와 형상이 유사한 천연고무받침의 비해 우수한 감쇠력을 가지고 있으며 기존 납 고무받침의 경우 납의 유해성이 문제되어 납을 사용하지 않은 고감쇠 고무받침에 대한 연구가 증가하고 있다. 본 연구에서는 고감쇠 고무받침을 대상으로 압축응력 의존성 및 주파수 의존성, 반복하중 의존성 등 다양한 특성에 대하여 실험을 실시하였다. 그리고 여러 계기지진파 상태에서 고감쇠 고무받침의 내진성능을 평가하기 위해 진동대 실험과 분석을 수행하였다. 축소교량에 고감쇠 고무받침을 적용한 모델을 사용했고, 지진격리와 비 지진격리로 구분하여 진행하였다. 그 결과 고감쇠 고무받침을 적용할 경우 비 지진격리의 경우에 비해 높은 감쇠효과를 보였으나 Mexico City와 같은 연약지반의 구조물에 지진격리를 적용할 경우 오히려 구조물의 응답이 증가하는 양상을 나타내 지진격리장치 적용성에 주의해야 할 것으로 판단된다.

Keywords

References

  1. Koo GH, Lee JH, Yoo B, "Performance Experiments and Analysis of Nonlinear Behavior for HDRB Using in Seismic Isolation, J. of EESK, EESK, Vol. 2, No. 4, pp.1-113, 1998.
  2. Jung GY, Ha DH, Park KN, Kim DH, "Experimental study on characteristics of low hardness rubber bearing", J. of KSCE, KSCE, Vol. 22, No. 6A, pp.1295-1307, 2002.
  3. Oh J, Jung HY, "An Experimental Study for the Shear Property Dependency of High Damping Rubber Bearings", J. of KSCE, KSCE, Vol. 30, No. 2A, pp.121-129, 2010.
  4. Takayama Mineo, "Isolation to 4 seconds-Sesimic Isolation Design", Engineering Books, 1997.
  5. J.S.S.I, "Introduction to Seismic Isolation Structure", Japan Society of Seismic Isolation, Ohmsa, 2002.
  6. Kelly JM, "A Seismic Base Isolation : Review and Bibliography", Soil Dynamics and Earthquake Engineering, Vol. 5, pp.202-216, 1986. DOI: http://dx.doi.org/10.1016/0267-7261(86)90006-0
  7. Lee IM, Earthquake and Soil, Korea Society Civil Engineering, Vol.35, No.5, pp.40-42, 1987.
  8. Kim YS, Im JS, Yun CB, Kim NS, "Shaking Table Tests and Simplified Anasysis of Bridge with Base Isolators Consisting of PTFE Plates and Rubber Rings", J. of KSCE, KSCE, Vol. 19, No. I-6, pp.899-906, 1999.
  9. Chung WJ, Yun CB, Kim NS, Seo JW, "Shaking table and psedodynamic tests for the evaluation of the seismic performance of base-isolated structures", Engineering Structures, Vol. 21, pp.365-379, 1999. DOI: http://dx.doi.org/10.1016/S0141-0296(97)00211-3
  10. Yi MW, Bijan S, "Shaking table testing of a base isolated model", Engineering Structures, Vol. 24, pp.1203-1215, 2002. DOI: http://dx.doi.org/10.1016/S0141-0296(02)00054-8
  11. Tsai MH, Wu SY, Chang KC, Lee GC, "Shaking table tests of a scaled bridge model with rolling-type seismic isolation bearings", Engineering Structures, Vol. 29, pp.694-702, 2007. DOI: http://dx.doi.org/10.1016/j.engstruct.2006.05.025
  12. Jeon BG, Chang SJ, Kim NS, "Seismic Performance Evaluation of Con-type Friction Pendulum Bearing System Using Shaking Table Test" J. of KSNVE, Vol. 21, No. 7, pp.599-608, 2011. https://doi.org/10.5050/KSNVE.2011.21.7.599
  13. Kim MK, Choun YS, Choi IK, "A Shaking Table Test for Equipment Isolation in the NPP(I):Rubber Beaing, J. of EESK, EESK, Vol. 8, No. 5, pp.65-77, 2004.
  14. ISO 22762, Elastomeric Seismic Protection Isolators Part-1 : Test Methods, 2010.
  15. ISO 22762, Elastomeric Seismic Protection Isolators Part-2 : Applications for bridge- specifications, 2010.
  16. Korea Road and Transportation Association, Limit-State based Bridge Design Specification, Ministry of Load Infrastructure and Transport, 2012.