• Journal of the Korean Geotechnical Society
• /
• v.19 no.2
• /
• pp.217-225
• /
• 2003

The ground reinforcement effect of pressure grouting depends on grout penetration into ground. It is not, however, easy to predict the grout penetration in the design process because of the heterogeneity of ground conditions. This study investigates the proper grouting pressure and grouting method through laboratory model tests for pressure grouting using loose to medium dense crushed rock and sandy ground using specially designed and fabricated device. The optimum injection pressure, grout quantity and injection time are investigated through performing pressure grouting under changing conditions of injection in this test. From the test results, it was found that optimum injection pressure covers the range of 3 to 4kg/cm$^2$.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.05b
• /
• pp.67-72
• /
• 1996

수격현상(Waterhammer)으로 인한 과도압력하중은 월성원자력발전소 비상노심냉각계통 (Emergency Core Cooling System : ECCS) 설계의 주요 고려사항이다. 비상노심냉각계통은 특수안전계통으로서 냉각재상실사고(Loss of Coolant Accident : LOCA)후 일차열수송계통을 다시 채워주고 핵연료 손상을 막기위해 노심으로부터 잔열 및 붕괴열을 제거한다. 일차열수송계통으로의 비상냉각수 주입은 고압주입, 중압주입, 저압주입 3 단계로 주입된다. 과도압력이 발생될 것으로 예상되는 고압주입과 중압주입에 대한 6가지 사례들이 ECCS의 배관과 지지대 설계를 위해 고려되었다. 모든 사례에 대한 비상노심냉각계통의 과도압력 현상은 PTRAN 코드에 의해 해석 되었고 해석된 최고과도압력은 설계압력보다 작음을 알게 되었다. 모든 사례의 최고압력과 최고차압은 비상노심냉각계통 배관 및 지지대 설계를 위한 응력해석 자료로서 사용될 것이다.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2009.05a
• /
• pp.1918-1923
• /
• 2009

결정질 암반에서 지하수의 수리적 특성을 파악하기 위해 수행되고 있는 수리시험 방법은 정률법, 정압법, 순간주입(회복)법 등 세 가지로 구분할 수 있다. 본 연구에서 다루는 정압주입시험 (Constant Head Injection Test, CHIT)은 위의 정압법의 한 종류로 토목공학, 지질공학 분야에서 대상 구간의 투수계수 추정을 위해 널리 쓰이는 수리 시험이며, 이는 단일 패커나 이중패커를 이용하여 시험 구간을 격리하고, 격리된 구간에 일정한 압력으로 물을 주입하여 주입되는 물의 양을 파악함으로써, 시험 구간의 수리전도도(Hydraulic conductivity)를 산출하는 전통적인 수리시험이다. 본 연구에서는 수치실험을 통해 시험 구간 및 주입 압력의 크기 등 인위적인 요인에 의해 도출되는 투수계수가 어떻게 달라지는지에 대해 평가해 보았다. 일반적으로 단열 암반에서 수행한 정압주입시험의 해석에 있어 매질을 균질, 등방성 다공질이라는 가정으로 구간별 투수량계수를 산출하기 때문에, 다공성 매질의 지하수 유동을 모사하는 MODFLOW를 수치모사 코드로서 이용하였다. 시험구간의 크기 및 주입압력에 대한 민감도 분석 결과, 시험구간의 크기에 상관없이 수치모의에서 입력한 수리전도도 값에 비해 낮은 수리전도도 값이 산출되었으며, 주입 압력이 클수록 산출되는 수리전도도 값이 매질의 수리전도도 값과 차이가 났다. 민감도 분석 결과 현장수리시험에서 정압 주입시험에 의한 구간별 수리전도도 산출함에 있어 시험구간의 크기와 주입 압력 값에 대하여 고려해야 한다고 판단된다.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2012.05a
• /
• pp.817-818
• /
• 2012

본 연구에서는 치과에서 마취 시 환자들의 고통을 최소화 하기위하여 무통마취를 위한 치과용 약물주입기를 구현하였다. 약물의 주입 시 통증을 최소화하기 위해서 온도를 $36{\pm}2^{\circ}C$ 범위로 제어하여 체온과 유사한 온도로 유지하였다. 이를 위하여 필름히터 방식을 이용한 치과범용국소약물(36mg, 2% 리도카인) 앰플 가열부를 설계하였다. 또한 약물이 주입되는 양을 능동적으로 제어하기 위하여 약물주입 환부의 환자별 흡수 속도 차이에 차등 주입을 위한 압력 측정 시스템을 구현하였다. 필름 형태의 압력 센서를 통하여 전달 압력을 측정하였으며 측정된 압력을 바탕으로 능동적으로 모터의 동작을 제어함으로써 약물주입시 환자의 고통을 최소화 할 수 있도록 구현하고자 하였다.

• The Journal of Engineering Geology
• /
• v.29 no.3
• /
• pp.201-209
• /
• 2019

Bottom-up multi-stage pressure grouting is widely applied to domestic slopes and tunnels. It involves injecting earth from the ground to the surface after drilling. Various reports of construction performance have demonstrated its wide applicability. However, little research has studied top-down multi-step pressure grouting in Korea, which involves injection from the surface. This paper compares the grouting effect of both the established bottom-up method and the top-down method in soil box and field tests. The soil box test showed that the bulb volume of the top-down method is ~24% less than that of the bottom-up method. The field test confirmed that the top-down method has a wider grouting range and a higher injection density per area than the bottom-up method.

• Resources Recycling
• /
• v.24 no.4
• /
• pp.56-60
• /
• 2015

Fine particle classification was performed using products obtained from primary classification process after flotation for efficient application of tailing. The cut size increased with decreasing input pressure from 0.1 MPa to 0.3 MPa and increasing pulp density from 5% to 15% using 2-inch hydrocyclone. The median sizes of overflow and underflow were $6.56{\mu}m$ and $55.45{\mu}m$, respectively at 0.3 MPa with 5% pulp density. The imperfection became closed to ideal separation with increasing the pulp density and decreasing the input pressure. The water content decreased with increasing the pulp density, but the effect of input pressure could be ignored. The water content of underflow was 27.9% at 0.3 MPa with 15% pulp density.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.42 no.4
• /
• pp.501-508
• /
• 2022

Required essential technique is to determine the maximum recharge pressure in the well with condition of non-ground failure for the recovery of the groundwater. Based on the classical soil mechanics, the maximum recharge pressure was estimated with the numerical anlaysis and laboratory triaxial test. In the numerical analysis, the maximum recharge pressure is defined as the ground failure stress. The ground failure of the sand was defined as the piping and the one of the caly was to the undrained failure by the confined pressure increment. In the triaxial test, the recharge pressure in the ground was modified by the back pressure in the specimen. In case of sand, the volume strain was dramatically increased at the 93 % of the maximum back pressure, same meaning of the 0 effective stress state. In case of clay, the only radial volume strain was to reached 1.5 % without failure. Therefore, The maximum recharge pressure could be determined with the numerical analysis and triaxial test.

• Journal of the Korean GEO-environmental Society
• /
• v.15 no.5
• /
• pp.23-29
• /
• 2014

So far, the grouting using pressure injection has been extensively used to avoid adverse effects such as soil disturbance. Whereas, the pressure injection to the limitations of the diffusion range, so that the kinks would last injection of cement particles by introducing a frequency oscillation effect improved injection method have been recently developed. In this study, a pilot test was performed to compare injection effects of the both methods. The injections using both methods were tested on the embankment which consists of core clay and weathered soil. Subsequently, the injected volume, SPT N values, in-situ permeability and electrical resistivity were measured to compare their effects. The vibration method showed more effective permeation comparing with the pressure method. Also, it showed more homogeneously improved ground than the existing method. For SPT results, the vibration method presented increase of mean N value as much as 17.4 % comparing with the conventional method. Higher electrical resistivity was presented in case of injecting with vibration method and it indicated the injection was extensively completed. Finally, it is expected that the economic feasibility will be improved by decrease of drilling spacing, when the existing method is replaced with vibration method.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.10 no.6
• /
• pp.191-197
• /
• 2006

This study is to establish a standardization of injection system by inorganic material for crack repair of tunnel concrete structures. For this various surveys and experiments were carried out as followed. The first we surveyed capability of injection and crack pattern of concrete structures in site. and second we analyzed the relationship between crack width and volume of injection, and decided pressure and volume of injection. Finally we evaluated the relationship between crack width and volume of injection with kind of concrete structures, and between required time for injection and crack width with thickness of structure. From these surveys and experiments, we cleared the relationship between crack patterns and injection technologies such as volume, pressure of injection and required time for injection with kind of structure.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.09a
• /
• pp.109-116
• /
• 2010

일반적으로 사용되는 비탈면 보강공법은 중력식 혹은 가압식 네일링, 앵커 등이 있다. 이들 공법은 주입재 주입압력이 중력식무압 혹은 낮은 압력의 가압에 의한 것으로서, 실제로 단층파쇄대, 붕적층, 이완 및 절리 등이 발달한 지반에서는 일정압력의 가압주입에 의한 지반보강과 보강재에 의한 네일링 효과를 동시에 기대해야 한다. 본 사례에서는 가압주입의 효과를 높이기 위해 보강구간을 일정한 간격으로 나누고 구간별 별도의 주입펌프를 연결하여 보강길이 전구간을 동시에 주입하는 멀티패커시스템(MPS)공법을 소개하고자 한다.