Park, Keum Sung;Lee, Sang Sup;Choi, Young Hwan;Bae, Kyu Woong
Journal of Korean Society of Steel Construction
/
v.21
no.3
/
pp.211-219
/
2009
The purpose of the study described in this paper was to experimentally investigate branch squared T joints with cold formed hollow structural sections under the in plane moment in a Vierendeel Truss. The branch in the T joints was welded to the upper flange of the chord. The main experimental parameters were the ratio of the width to the thickness of the chord ($2{\gamma}$), with ${16.7{\leq}2{\gamma}{\leq}33.3}$, and the width ratio of the branch to the chord ($\beta$), with ${0.40{\leq}{\beta}{\leq}0.71}$. Nine specimens were tested and manufactured in joints under the in plane bending moment. Based on the results of the test, the in plane moment strength of the branch squared T joints was determined according to the bending deformation of the chord flange yielding, regardless of the ratio of the width to the thickness of the chord and the ratio of the width of the branch to the width of the chord. Also, the in plane moment strength of the branch squared T joints in the hollow structural sections can be defined as 1.5 times the moment load at M1%B the strength of the joints that governed the serviceability in the control group. Finally, the experimental results with the branch squared T joints show that the in lane moment strength of the joint increased as $2{\gamma}$ decreased and $\beta$ increased.
This paper's objective is to evaluate the experimental behavior of gap N-joints made of cold-formed, square, hollow steel sections, with a connection plate as a tension member. The principal parameters for testing included the ratio of chord width to thickness, the ratio of brace width to chord width, eccentric ratio, the shape of the compression member, the branch angle, and the stiffening plate of the chord flange. The strength and failure mode were examined through the test for the gap N-joint, consisting of several parameters. Based on the results of the test, the gap N-joints were determined according to the capacity preceding the displacement of the tension, regardless of the width ratio, and the split failure mode-connected surface for a chord in joints. The strength of the gap N-joints increased proportionally as the $2\gamma$(B/T) ratio decreased, and as the width ratio(${\beta}$) of branch to chord increased. Particularly, $2\gamma$(B/T) decreased as the capacity of gap N-joint increased. The results of the test were summarized for the capacity, initial stiffness, ductility, and change of the failure mode of each gap N-joint.
Park, Keum Sung;Lee, Sang Sup;Choi, Young Hwan;Bae, Kyu Woong
Journal of Korean Society of Steel Construction
/
v.21
no.5
/
pp.451-459
/
2009
The purpose of this study was to evaluate the in-plane bending moment for T-joints made of cold-formed square hollow steel sections. In the previous studies, the T-joint was shown not to have an obvious peak load, and the failure mode was the main chord flange failure at the branch-width-to-chord-width ratio ($\beta$) of below 0.71. Based on the experimental results, including the tests conducted by Zhao, the deformation limit of 1% B was proposed for ${16.7{\leq}2{\gamma}(=B/T){\leq}33}$ and ${0.34{\leq}{\beta}(=b_{1}/B){\leq}0.71}$. Then, the ultimate in-plane bending strength was shown to be Mu=1.5${\cdot}$M1% B. The existing strength formulae for the original T-joint were investigated and were determined to be the main chord flange failure for the branch-squared T-joint. The bending strength formulae of CIDECT and other researchers were compared with the test results. Finally, a reasonably good agreement with Zhao's formula was found. Therefore, the design guidelines were presented based on Zhao's strength formula for T-joints.
This paper described the ultimate strength and deformation limit of welded T-joints in cold-formed square hollow sections. Previous studies showed that the strength of a T-joint still increases with increasing deformations at a ratio of branch width to chord width (${\beta}$) of below 0.8. Therefore, the strength at a certain deformation (chord flange indentation) limit can be regarded as the ultimate strength of a T-joint. The chord flange failure modes were investigated for the ratio of branch width to chord width (${\beta}$) and the ratio of chord width to chord web thickness (B/T). Experimental results including tests done by Kato proposed a deformation limit of 3%B for $16.7{\leq}B/T{\leq}41.6$ and $0.27{\leq}{\beta}{\leq}0.8$. The strength formula of CIDECT and other researchers were compared with the test results. Finally, the strength formula based on yield-line theory was proposed.
There are many restrictions in the application of high-strength HSSs, including yield strength and yield ratio for the 600-MPa steel. The AISC and Canadian codes recommend that the yield strength and yield ratio of HSS members be 360 MPa and 80%, respectively. It is important to understand the true buckling behaviors of HSSs using high-strength steel at the limit states. There are many experimental data regarding the rectangular HSSs, and the circular ones are not enough for high-strength steel. Therefore, this study was conducted to create a better understanding of the buckling behaviors of the 600- and 400-MPa steels based on the results of the finite-element analysis that was done before the experiment. To understand the structural behaviors of the aforementioned steels, the width-to-thickness ratios, the angle of the web members, the yield strength, and the gap of the web members were selected as the main parameters in this study, and ABAQUS, a general finite-element program, was used.As a result, the compression web member reached elastic buckling in the 600-MPa steel and inelastic buckling in the 400-MPa steel. A brittle fracture occurred in the case where the yield ratio was greater than 80%. At the same time, it was found that the limit strength determined via FEM analysis had a higher value compared to the code evaluation with the variation of the width-to-thickness ratio in the main code member. The change in the connection load in high-strength steels was not identified by the other factors.
Kim, Sung-Jun;Kim, Tae-Il;Seol, Yang-Jo;Cho, Ki-Young;Ku, Young;Rhyu, In-Chul;Chung, Chong-Pyoung;Han, Soo-Boo;Lee, Yong-Moo
Journal of Periodontal and Implant Science
/
v.35
no.3
/
pp.537-548
/
2005
1. 목적 이 연구의 목적은 기존의 평가기준에 따라 관찰자에 의해 주관적으로 판단된 치은형과 실제 치은두께와의 상관관계를 규명하고 임상검사 시에 측정할 수 있는 변수들과 치은두께의 연관성을 평가하는 것이다. 2 방법 211명의 치과대학생(22-43세, 평균 24.7세)을 연구대상으로 하여 상악중절치부위에서 국소마취하에 근관 치료용 파일을 치은에 삽입하여 두께를 측정하고 임상검사를 통해 치주낭깊이, 치태지수, 치은지수, 치은퇴축, 체형 및 비만도, 피부형, 치경부의 형태, 관측자가 임의로 판단한 치은형을 기록하였다. 임상사진으로 치관의 폭경과 길이의 비율, 치은외형의 만곡정도를 조사하고 평행촬영법을 이용한 방사선사진으로 치아의 장평비율 및 치아의 치관 폭경과 치경부 폭경의 비율을 조사하였다. 전체 대상을 치은의 두께를 기준으로 평균두께보다 얇은 군과 두꺼운 군의 두 개의 군으로 분류하여 임상검사 사에 측정한 변수들이 각 군 간에 유의할 만한 차이를 보이는지와 임의로 판단한 치은형이 실제 치은두께와 연관이 있는지를 알아보았다. 통계처리는 Student t-test를 이용하였다. 3. 결과 치주낭 깊이, 치은지수, 체형 및 비만도, 피부형, 치아의 형태, 치경부의 형태, 치아의 장평비율의 경우 실제 측정하여 얻은 치은의 두께와의 상관관계는 통계적으로 유의성이 없었다. 치은의 형태는 치은의 두께와 상관성은 보이고 있으나 통계적으로 유의하지 않았다. 관측자가 임의로 평가한 치은형과 실제 측정치도 유의할만한 일치를 보이지 않고 있다. 4. 결론 치은의 형태는 치은의 두께를 예상하는데 약간의 도움이 될 수 있으나 실제 치은의 두께는 임상적으로 간단히 측정할 수 있는 겸사지수들과 직접적인 상관관계를 보이지 않았다. 따라서 치료결과의 예측에 있어서 치은형을 분류하여 예상하는 것은 큰 도움이 되지 않는다고 할 수 있다.
The object of this paper is to determine appropriateness for use of high-strength tensile bar as a tension web member. The gap K-joint of tensile bar types were compared with gap K-joint of square hollow section (SHS) types. For the same width-to-thickness ratio ($2{\gamma}=33.3$ ), tests were performed on four specimens of the SHS type and eight specimens of the tensile bar type. The comparison of capacity with the experimental results showed a capacity of the SHS type joint to be higher than that of the tensile bartype joint for the same brace-to-chord width ratio. Moreover, the capacity of the SHS type joints increased proportionally to the width ratio ${\beta}$), while tensile bar type joints increased as the tension width ratio (${\beta}2$). In failure mode, SHS-type specimens showed local buckling of the compression brace and plastic failure was observed between the tension brace and chord face, and with the tensile bar type specimens there appeared punching shear failure of the chord face at the toe of the connection plate. It is, therefore, concluded that width-to-thickness ratio should be lower than that of the hollow-section type and the relation between tension and compression width ratio should be considered.
Proceedings of the Korea Society of Costume Conference
/
2003.05a
/
pp.42-42
/
2003
세계적으로 인터넷 이용 인구는 2002년 2월 현재 5억 4천 4백만여명에 이르고 있으며, 우리나라의 인터넷 이용 인구는 2001년 12월말 자료에 의하면 2천4백3십8만여명에 달하는 것으로 보고되고 있다(한국 인터넷정보센터통계보고서, 2002). 또한, 네오위즈는 작년 한 해 아바타 매출 100억원을 돌파, 다모임은 지난해 12월 한달간의 아바타 매출이 3억 6000만원에 달하였으며, 다움(Daum)의 경우 서비스 개시 15일 만에 일일 발생 매출이 1천만원 돌파, 현재 1일 3천500만원의 수익을 올리는 등, 아바타 선두 업체 뿐 아니라 후발 주자들도 큰 수익 창출하고 있다(Economy21- 2002.04.25). 올 한해 아바타 시장규모는 800억원-1000억원으로 예상되고 있으며, 이러한 시장 증대에 따라 기존 캐릭터 업체들이 구축계약 위주에서 서비스 제휴사업으로 아바타모델 제안 및 시장영업이 증대되고 있다. 즉, 아바타 시장은 구축되어 있는 것이 아니라 계속적으로 확대되어 가고 있음. 또한 아바타산업은 인터넷 인프라의 확산과 더불어 아바타의 호응 또한 급격히 상승하고 있으며, 단순히 사이버 세계에서의 분신으로서의 역할에서 벗어나 다양한 부가가치를 구현하는 아바타의 등장으로 아바타의 확산은 계속적인 추세이다. 또한 아바타는 게임, 채팅, 일정관리등 인터넷 전 분야에 걸쳐 Cyber Agent활용도가 확산되고 있으며, 아바타 시장은 초기 일본형 애니메이션 아바타에서 벗어나 아바타와 패션, 아바타와 문화의 접목에 대한 관심이 상승되고 있으며 이로 인한 신규시장이 창출되고 있다 이러한 디지털 시대로의 급격한 발전은 복식문화를 디지털 문화컨텐츠 사업화로의 그 발전방향을 제시하고 있다.2cm 적용하고, 진동두께 계산식은 (B/8-1.5)+2cm를 적용함으로써 진동깊이와 진동두께의 편차가 작아짐으로 인해 소매부위와 진동부위의 맞음새를 향상시켰다. 3) 가슴둘레의 증가에 따라 등길이에 앞길이 치수를 증가시키는 계산식을 설정하여 앞가슴둘레의 맞음새를 향상시켰다. 4) Plus-size여성의 경우 허리부분의 신체적합성을 높이기 위하여 사이드 판넬(side panel)의 재킷원형으로 하였다. 앞 허리와 배 부분의 지방 침착이 크므로 앞 허리둘레 다아트 폭과 앞판 사이드 판넬(side panel) 솔기 다아트 폭을 작게 설정하고, 뒤판 사이드 판넬 솔기 폭을 크게 설정하였다. 5) 어깨끝점 사이길이는 다른 부위의 체지방 침착과 같이 비례적으로 증가하지 않으므로 표준체형에 비해 좁게 설정하였다. 보여주어 우리나라의 선호 질감과는 차이가 있었다. 실제 판매율을 살펴본 결과 주관적 질감 이미지 평가의 선호도와의 비교에서 약간의 차이가 있었는데, 이는 질감 외에 가격이 구매에 영향을 미쳤기 때문으로 분석되었다., 2002; Huun et al, 2001).의 특징이라 할 수 있겠다. 대한 자부심과 국제 사회에서 차별화 할 수 있는 한국 복식 디자인에 독창성과 창조성을 표현하는 중요한 영역임을 인식할 수 있었다.와 보호인자를 재확인할 필요가 있다고 보며 본 연구의 결과는 지역민의 대장직장암 예방을 위한 영양교육 자료로서 활용될 수 있다고 본다. 관여도에 영향을 미치고 있음을 알 수 있었다. 유지되어 쾌적역이 향상된 것으로 사려된다.하였으며, 효율적인 색채 정보로서 활용될 수 있는 패션 색채 팔레트를 제시하였다는데 의의가 있다.′, aesthetic of ′unity in multiplicity′, a
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.