• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.10C
• /
• pp.929-936
• /
• 2009

In this paper, we consider designing a multi-input multi-output (MIMO) overlay system for fixed MIMO wireless link, where a frequency flat narrowband channel is shared by multiple transmitter and receiver pairs. Assuming the perfect knowledge of the second-order statistics of the received legacy signals and the composite channels from the overlay transmitter to the legacy receivers, the jointly optimal linear precoder and decoder matrices of the MIMO overlay system is derived to minimize the total mean squared error (MSE) of the data symbol vector, subject to total average transmission power and zero interference induced to legacy MIMO systems already existing in the frequency band of interest. Furthermore, the necessary and sufficient condition for the existence of the optimal solution is also derived.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.11a
• /
• pp.677-684
• /
• 2004

This paper describes a method for identifying the dynamic characteristics of air foil bearings for high speed turbomachinerys with the LS/IV method. In fact identifying the characteristics of air foil bearings is very difficult work, and it is tried to identify it. Experiments were conducted to determine the structural dynamic and hydrodynamic characteristics of air foil bearings. Numerical predictions compare the static and dynamic force performances. The housing of the bearing on the journal was driven by the impact hammer which were used to simulate impact force acting on air foil bearings. The characteristics of air foil bearings were extracted from the frequency response function (FRF) by LS(Least Square) method and IV(Instrumental Variable) method. The experiment was tested at 0 rpm and $10000\sim16000rpm$. And the test results were introduced about the dynamic characteristics of air foil bearings, and also compared with theoritical results.

• The Journal of the Korea Contents Association
• /
• v.9 no.11
• /
• pp.254-261
• /
• 2009

This study suggested that the table of CT-simulator and the laser alignment system using diagnostic CT scanner have an efficient method for improvement in alignment between the planned target center of traverse image with CT scanner. It was conducted on the daily QA when presented in the AAPM TG66 with correcting the laser alignment system using geometric trigonometric functions and investigated the effectiveness of correction methods as compared with those before and after correction. Before correction error was 3.82mm between the planned target center of image, the table longitudinal axis was twisted with 0.436o. The laser alignment system using geometric trigonometric functions in after correction was satisfied with tolerance limits of ${\pm}2mm$ when occurred about 0.7mm in errors between the planned target center. The table correction to satisfy the geometric accuracy is very inefficient over against the time and economic loss as well as technical limits in the case of application as only radiation therapy associated with CT-simulator with diagnostic CT scanner in use. But, the method which corrects the laser alignment system is economic and relatively simple with possibility of getting well geometric accuracy and we suppose that it is efficient method for applying in the clinic.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.19 no.4 s.74
• /
• pp.429-440
• /
• 2006

This paper comprises two specific objectives. The first is to examine the applicability of ordinary kriging interpolation(OK) to the p-adaptivity of the finite element method that is based on variogram modeling. The second objective Is to present the adaptive procedure by the hierarchical p-refinement in conjunction with a posteriori error estimator using the modified S.P.R. (superconvergent patch recovery) method. The ordinary kriging method that is one of weighted interpolation techniques is applied to obtain the estimated exact solution from the stress data at the Gauss points. The weight factor is determined by experimental and theoretical variograms for interpolation of stress data apart from the conventional interpolation methods that use an equal weight factor. In the p-refinement, the analytical domain has to be refined automatically to obtain an acceptable level of accuracy by increasing the p-level non-uniformly or selectively. To verify the performance of the modified S.P.R. method, the new error estimator based on limit value has been proposed. The validity of the proposed approach has been tested with the help of some benchmark problems of linear elastic fracture mechanics such as a centrally cracked panel, a single edged crack, and a double edged crack.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.7A
• /
• pp.724-729
• /
• 2007

In this paper, we consider a joint optimization of transmitter and receiver in additive cyclostationary noise with zero forcing criterion. We assume that the period of the cyclostationary noise is the same as the inverse of the symbol transmission rate and that the noise has a positive-definite autocorrelation function. The data sequence is modeled as a wide-sense stationary colored random process and the channel is modeled as a linear time-invariant system with a frequency selective impulse response. Under these assumptions and a constraint on the average power of the transmitted signal, we derive the optimum transmitter and receiver waveforms that jointly minimizes the mean square error with no intersymbol interference. The simulation results show that the proposed system has a better BER performance than the systems with receiver only optimization and the systems with no transmitter and receiver optimization.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1994.10a
• /
• pp.231-237
• /
• 1994

컴퓨터의 눈부신 발달에 힙입어 실험 또는 해석적 방법으로 일반 구조물이나 기계구조물의 진동특성을 손쉽고 정확하게 파악하는 것이 가능하게 되었다. 그런데 최근의 산업현장은 지금까지의 정확한 구조해석에만 그치지 않고 이를 바탕으로 강도 개선, 재료 절감을 통한 원가절감, 중량 최소화 문제등의 차원에서 동적인 특성의 변경을 요구하고 있다. 이러한 문제는 그 중요성에도 불구하고 여전히 설계자의 경험이나 시행착오에 의존하고 있는 실정이다. 본 연구에서는 구조물 결합부분에 주목하여 동특성의 변경 문제를 해석하고자 하였다. 즉 거의 모든 구조물이 결합부를 가지고 있는데 결합부 특성을 정확히 파악할 수 없기 때문에 리벳이나 보울트나 어떤 특수한 형태 결합부가 구조물의 특성에 주는 영향을 예측하기 어렵다. 이러한 결합부이 특성을 알아내고 구조물 동특성 변경 및 개선안을 제시하는 최적설계를 위해 감도해석기법은 아주 유효하게 쓰일 수 있다. 한편 구조물의 대형화, 복잡화는 구조물 동특성 해석에 더욱 많은 계산시간과 용량이 큰 전자계산기를 필요로 하게 되었으며, 분계의 결합부위가 변경되거나 결합형태가 변했을 때 전계의 동특성을 다시 해석할 필요없이 분계만의 정보로부터 전계의 동특성을 알아낼 필요가 생겼다. 이러한 의미에서 구조물의 분계로부터 전계의 동특성을 해석을 위한 부분구조합성법이 대두되게 되었다. 본 연구에서는 이러한 감도해석과 부분구조합성법의 공통된 문제를 일치화하고자 하였다. 즉 감도해석기법을 이용하여 필요한 구조물의 동특성에 부합하는 결합부의 최적한 설계변수를 규명하였고 이렇게 구해진 결합부의 설계변수와 분계의 정보를 알고리즘이 비교적 간단하고 오차가 적은 축소임피던스 합성법에 적용하여 전계의 동특성을 해석함으로써 감도해석기법과 축소임피던스 합성법의 통합적용이 최적설계와 이에 따른 동특성 해석에 효과적인 방법임을 보이고자 하였다. 대상구조물은 구조물 결합의 기본적인 형태인 T형을 선택하였다. T형 구조물은 분계 A(16개의 사각요소)와 분계 B(8개의 사각요소)로 이루어져 있으며 두개의 스프링으로 결합되어 있다. 설계변수는 강성에 국한하였으며 결합부의 결합형태는 탄성결합과 강결합으로 하였다. 감도해석과 축소임피던스 합성법에 의해 구해진 고유진동수와 FRF를 상용 유한 요소 해석 패키지인 MSC/NASTRAN을 통하여 검증하여 이 연구의 타당성을 검토하였다.

• Journal of Korean Association for Spatial Structures
• /
• v.8 no.4
• /
• pp.81-90
• /
• 2008

This paper presents a finite element formulation for the three-dimensional hierarchical solid element using Integrals of Legendre polynomials. The proposed hexahedral solid element is composed of four different modes including vertex, edge, face, and internal mode, respectively. The eigenvalue and patch test have been carried out to confirm the zero-energy mode and constant strain condition. In addition to these, a posteriori error estimation has been studied for the p-adaptive finite element analysis that is based on a smoothing technique to compute a post-processed solution from the finite element solution. The uniform p-refinement and non-uniform p-refinement are compared in terms of convergence rate as the number of degree of freedom is increased. The simple cantilever beam is tested to show the performance of the proposed solid element.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.7
• /
• pp.23-29
• /
• 2011

A dB-linearity improved variable gain amplifier (VGA) for GPS receiver is presented. The Proposed dB-linear current generator has improved dB-linearity error of ${\pm}0.15$dB. The VGA for GPS is designed using proposed dB-linear current generator and composed of 3 stage amplifiers. The IF frequency is assumed as 4MHz and the linearity requirement of the VGA for GPS receiver is defined as 24dBm of IIP3 using cascaded IIP3 equation and the VGA satisfies 24dBm when minimum gain mode. The DC-offset voltage is eliminated using DC-offset cancelation loop. The gain range is from -8dB to 52dB and the dB-linearity error satisfies ${\pm}0.2$dB. The 3-dB frequency has range of 35MHz~106MHz for the gain range. The VGA is designed using 0.18${\mu}m$ CMOS process. The power consumption is 3mW with 1.8V supply voltage.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.25 no.5
• /
• pp.437-449
• /
• 2007

This paper deals with issues of GPS network adjustment for the purpose of determining the $3^{rd}$ order national geodetic control points based on the Korean Geodetic Datum which has newly adopted in the country since early 2003. After examining and arranging all the observations, GPS baseline analyses were performed to estimate baseline vectors between two control points. All the observations were divided into 17 block networks in order to accelerate the adjustment efficiency. After applying a minimally constrained adjustment technique to each of the block networks for the sake of detecting outliers and examining network precision, over constrained adjustments by fixing all of the $2^{nd}$ order control points within the block network were carried out to derive final coordinate sets. The final solutions indicated that the accuracy of the adjusted coordinates was better than 1cm and 2cm in the horizontal and vertical component, respectively.

• Journal of Sensor Science and Technology
• /
• v.8 no.6
• /
• pp.461-468
• /
• 1999

In this paper, we have implemented a gas recognition system for classification and identification of explosive gases such as methane, propane, and butane using a sensor array and an artificial neural network. Such explosive gases which can be usually detected in the oil factory and LPG pipeline are very dangerous for a human being. We analyzed the characteristics of a multi-dimensional sensor signals obtained from the nine sensors using the principal component analysis(PCA) technique. Also, we implemented a gas pattern recognizer using a multi-layer neural network with error back propagation learning algorithm, which can classify and identify the sorts of gases and concentrations for each gas. The simulation and experimental results show that the proposed gas recognition system is effective to identify the explosive gases. And also, we used DSP board(TMS320C31) to implement the proposed gas recognition system using the neural network for real time processing.