• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.2
• /
• pp.105-109
• /
• 2002

The wet etching characteristics of magnetic materials such as NiFe and CoFe were investigated in terms of etch rate and etch profile by using variouus etching solutions (etchants). Among the various etching solutions, HNO$_3$, HCl, and H$_2$SO$_4$were selected for the etching of magnetic materials and showed distinct results. In the case of NiFe films, faster etch rate were obtained with HNO$_3$solution. When NiFe films ere etched with HCl solution, white etch residues were found on the surface of etched films. From FEAES analysis of these etch residues, they were proved to be by-product from the reaction of NiFe with Cl element. CoFe thin films showed the similar trend to the case of NiFe films. They were etched fast in HNO$_3$ solution while Chl solution represented slow etching. The etch profiles of CoFe films showed smooth etch profile but revealed the partial etching around the patterns in HNO$_3$solution of relatively high concentration. It was observed that the etched surface was clean and smooth, and that white etch residues were also remained on the etched films.

• Journal of ILASS-Korea
• /
• v.7 no.3
• /
• pp.38-44
• /
• 2002

The purpose of this study is to investigate the effect of the volume fraction of water and injection pressure on the spray characteristics of water/oil emulsified fuel injected from the pressure swirl atomizer. The mixture of light oil and water by using impeller mixer was performed. The spray characteristics such as SMD and velocity were measured using PDPA. The injection pressures were 7.5, 100, 200 and $300kgt/cm^2$ and volume fractions of water in emulsified fuel were 0, 10, 20 and 30%, respectively. The measurement sections were at 30, 60 and 90mm from injection nozzle tip. SMD and velocity of emulsified fuel were larger gradually by increasing the volume fraction of water in emulsified fuel. The spray angle was decreased and axial velocity was increased with increase in water content. It was found that the relative SMD ratio was increased more greatly than the relative axial velocity ratio in super critical pressure. The relative SMD ratio was increased and the relative axial velocity ratio was decreased with increase injection pressure at spray downstream.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.3 no.3
• /
• pp.579-586
• /
• 1999

In this paper, we have analyzed a performance of fast frequency hopping communication systems when a rayleigh fading caused by envelope variations of a signal received in multipath channel is, but it is not considered that intentional or unintentional jamming can be. The multipath fading channel and rayleigh fading are confirmed by theoretical analysis. In fading or non-fading, the performance of this system is studied. When the path diversity is applied to this system, the performance is shown to be superior to non-diversity systems about 20dB. For modulation methods, BFSK was compared with DPSK.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2013.10a
• /
• pp.399-401
• /
• 2013

In this paper, we present the method to impove the performance by using iterative decoding in LDPC codes with 8-PSK modulation. Iterative decoding is the technique that improve the performance after the input signals of receiver are re-calculated by using the soft decision output of decoder. DVB-S2 system with 8-PSK modulation based on iterative decoding had a better performance than DVB-S2 with 8-PSK modulation over Gaussian channels.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.3C
• /
• pp.216-225
• /
• 2007

This paper presents bit splitting methods to apply multilevel modulation to iterative codes such as turbo code, low density parity check code and turbo product code. Log-likelihood ratio method splits multilevel symbols to bits using the received in-phase and quadrature component based on Gaussian approximation. However it is too complicate to calculate and implement hardware due to exponential and log calculation. therefore this paper presents Euclidean, MAX and Sector method to reduce the high complexity of LLR method. We propose optimal bit splitting method for three iterative codes.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.37 no.3
• /
• pp.11-16
• /
• 2000

In this paper, a real-time implementation of scene-based non-uniformity correction by digital technique is proposed for microscan-mode staring infrared cameras. Most scene-based non-uniformity correction algorithms, without sensor motion, can not be applied to stationary scenes because of image blurring and fading. Using microscanning effect, coupled with a modified version of Scribner's algorithm, the proposed technique can correct the artifacts and non-uniformities in real time Computer simulations and hardware experiments demonstrate substantial Improvement of image qualities in stationary as well as moving scenes.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.24 no.8
• /
• pp.94-100
• /
• 2010

Grounding system insures a reference potential point for electric devices and also provides a low impedance path for fault currents or transient currents in the earth. The ground impedance as function of frequency is necessary for determining its performance since fault currents could contain a wide range of frequencies. In this paper, the grounding resistance, grounding impedance and transient grounding impedance are measured by using 3-point fall-of-potential method in order to analyse grounding characteristics of the stainless-steel plate grounding electrode. An equivalent transfer function model of the grounding impedance and transient grounding impedance are identified from the measured values by using ARMA method and evaluated by comparing conventional grounding impedances.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.12
• /
• pp.2791-2797
• /
• 2010

In recent years, the goal of providing high speed wireless data services has generated a great amount of interest among the research community. Several researchers have shown that the capacity of the system, in the presence of flat Rayleigh fading, improves significantly with the use of combined MIMO and LDPC. To feed the soft values to LDPC decoder, the soft values must be calculated from multiple transmitter and receiver antennas in Rayleigh fading channel. It requires high computational complexity to get the soft symbols by increasing number of transmitter and receiver antennas. Therefore, this thesis proposed on effective algorithm for calculation of soft values from multiple antennas based on LLR. As result, This thesis shows that maximum 61% of computational complexity is reduced with a little loss of performance.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2013.10a
• /
• pp.402-404
• /
• 2013

The wireless communication channel different speed by depth of water or salt and it is influenced by multi-path according underwater. In the paper, MIMO(Multi-input-Multi-Output) system used turbo Equalizer combining Equalizer with Turbo codes for data rates by multi-path channel. we proposed and simulated that the Decision-Directed method used for phase offset. The simulation of proposed method show that the bit-error rate performance can be severely affected by phase errors.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.5C
• /
• pp.485-497
• /
• 2009

In this paper, we described DVB-S2 system for mobility. cross layer coding technique are needed to maintain the performance in deep fading channel. Cross layer coding is divided into two kinds of level. First level is Physical layer coding and, second layer is link layer or upper layer coding. Fixed on DVB-S2 short frame coding method as a physical layer, we simulated the various coding method as an upper layer coding. Furthermore, we analyzed the performance of each coding method on according to mobile vehicle speed, data rate, interleaving memory size, and IP packet size.