• Proceedings of the Korean Society for Emotion and Sensibility Conference
• /
• 2009.05a
• /
• pp.157-160
• /
• 2009

자동차는 지난 한 세기의 짧은 역사를 가지고 현재에 이르기까지 급속한 발전을 이루어왔다. 초기의 기능은 단순히 운송수단과 부의 상징이었지만 최근에는 소비자의 감성과 문화적인 흐름을 반영하는 모습이다. 그리하여 소비자의 감성 분석이 자동차 내장의 가장 중요한 부분으로 여기게 되었다. 자동차에 대한 새로운 감성요구를 실현하기 위해서는 인체와 오랜 시간 접촉해 있는 시트 표피재의 분석이 반드시 필요하다. 본 연구에서는 자동차 시트 표피재의 역학적 특성과 감성을 고려한 고급감을 예측하여 고감성 내장 표피재 개발에 기여하고자 한다. 감성용어는 Softness(유연한), Elasticity(탱글탱글한), Volume(풍성한), Stickiness(끈끈한)를 설정하였으며, 이와 대응하는 표피재의 역학적 특성 치를 측정하였다. 감성 평가에서는 현재까지 알려진 가장 확실하고 재현성 있는 측정법인 일대일 비교법을 통해 고급감에 대해 평가하였다. 이를 통하여 역학적 특성 치와 인간의 감성 평가 치와의 회귀 분석을 실시하여 평가 예측을 가능케 하였다. 즉, 자동차 표피재 중 피혁의 4 가지 물리량으로 인간의 감성인 표피재의 고급감을 예측하여 고감성 자동차 시트 표피재의 개발을 위한 평가 모델링을 구축하였다.

• Journal of Korean Society of Water and Wastewater
• /
• v.18 no.5
• /
• pp.656-665
• /
• 2004

An Ozone reaction model combined with CFD(Computational Fluid Dynamics) technique was developed in this research, in the simulation of ozonation, hydrodynamic behavior as well as reaction model is important because ozone is supplied to treated water as gas ozone. In order to evaluate hydrodynamic behavior in an ozone contactor, CFD technique was applied. CFD technique elucidated hydrodynamic behavior in the selected ozone contactor, which consisted of three main chambers. Three back-mixing zones were found in the contactor. The higher velocities of water were observed in the second and third compartments than that in the first compartment. The flow of the opposite direction to the main flow was observed near the water surface. Based on the results of CFD simulation, the ozone contactor was divided into small compartments. Mass balance equations were established were established in each compartment with reaction terms. This reaction model was intended to predict dissolved ozone concentration, especially. We concluded that the model could predict favorably the mass balance of ozone, namely absorption efficiency of gaseous ozone, dissolved ozone concentration and ozone consumption. After establishing the model, we discussed the effect of concentration of gaseous ozone at inlet, temperature and organic compounds on dissolved ozone concentration.

• Proceedings of the Korean Society Of Semiconductor Equipment Technology
• /
• 2007.06a
• /
• pp.203-206
• /
• 2007

연속 전자 모델과 결합된 종래의 분자 동역학 방법은 원자 사이의 힘과 원자의 전기용량에 의해 야기되는 탄소 나노튜브의 구부러지는 성질의 특성을 해석하였다. 탄소 원자의 전기 용량은 탄소 원자의 길이에 따라 변하였다. 본 연구는 11.567nm($L_{CNT}$)의 길이와 $0.9{\sim}1.5nm(H)$의 안쪽 깊이를 가진 (5,5) 탄소 나노튜브 브리지로 MD 시뮬레이션을 수행하였다. 탄소 나노튜브는 금 표면에 부딪힌 후 탄소 나노튜브 브리지는 약 ${\sim}1{\AA}$의 크기로 금 표면에서 진동하며, 크기는 차츰 감소하였다. $H{\leq}1.3nm$일 때, 탄소 나노튜브 브리지는 첫 번째 충돌 후에 금 표면과 계속 접촉해 있었고, $H{\leq}1.4nm$일 때, 탄소 나노튜브 브리지는 몇 번의 충돌 후에 금 표면과 안정한 접촉상태가 되었다. $H/L_{CNT}$가 0.13보다 작을 때, 탄소 나노튜브 초소형 전자기기 메모리는 반영구적인 비활성의 메모리 장치가 되는 반면에 $H/L_{CNT}$가 0.14보다 클 때 탄소 나노튜브 초소형 전자기기 메모리는 휘발성이거나 스위치 장치로 동작할 수 있다.

• Journal of IKEEE
• /
• v.7 no.1 s.12
• /
• pp.119-126
• /
• 2003

This paper presents a methodology for constructing a surgical simulation environment for the replacement of artificial knee join using CT image data. We provide a user interface of preoperative planning system for performing complex 3-D spatial manipulation and reasoning tasks. Simple manipulation of joystick and mouse has been proved to be both intuitive and accurate for the fitness and the wear expect of joint. The proposed methodology are useful for future virtual medical system where all the components of visualization, automated model generation, and surgical simulation are integrated.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.7
• /
• pp.751-756
• /
• 2014

The dynamic behavior of numerous grains interacting with each other can be easily observed. In this study, this dynamic behavior was analyzed based on the contact between numerous grains. The discrete element method was used for analyzing the dynamic behavior of each particle and the neighboring-cell algorithm was employed for detecting their contact. The Hertzian and tangential sliding friction contact models were used for calculating the contact force acting between the particles. A GPU-based parallel program was developed for conducting the computer simulation and calculating the numerous contacts. The dam break experiment was performed to verify the simulation results. The reliability of the program was verified by comparing the results of the simulation with those of the experiment.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.31 no.2
• /
• pp.174-180
• /
• 2011

Nondestructive surface imaging of elastic characteristic and mechanical property has been studied on nanoscale surface with ultrasonic AFM. Resonance frequency variation of cantilever is theoretically analyzed with respect to contact mechanics as well as experimentally measured. The contact resonance frequency is calculated theoretically using the spring-mass and Herzian model in accordance with the resonance frequency of UAFM cantilever measured experimentally. Consequently, the topography and amplitude images could be obtained successfully and the elastic characteristic at the nanoscale surface was evaluated qualitatively by amplitude signals.

• Tribology and Lubricants
• /
• v.31 no.4
• /
• pp.163-169
• /
• 2015

This paper describes a design method for the corner radius of a contacting body using the theoretical approach of contact mechanics. A complete contact, as in the case of a sharp-cornered punch, produces singular contact traction: whereas, in an incomplete contact, the singular contact traction disappears because of the rounded corners, and the contact edges are within the rounded regions. The design method aims to determine the conditions of the contact force as well as the material properties in an incomplete contact. The incomplete contact changes into the complete contact again when the contact edges exceed the rounded regions owing to either an increased contact force or the compliance of the materials. The contact length of a rounded punch is used as a parameter to derive the required conditions. As a result, a design formula is obtained, which provides a minimum allowable radius when the materials, normal contact force, and the length of a flat region of the punch are predetermined. This work consists of two parts: Part I includes a theoretical background, design method, and formula, and Part II describes the actual process with the investigation of design parameters.

• Journal of IKEEE
• /
• v.26 no.4
• /
• pp.681-685
• /
• 2022

Including the COVID-19 crisis, humanity is constantly exposed to viral infections, and efforts are being made to prevent the spread of infection by quickly isolating infected people and tracing contacts. Passive epidemiological investigations that confirm contact with an infected person through contact have limitations in terms of accuracy and speed, so automatic tracking methods using various digital technologies are being proposed. This paper verify contact by utilizing Bluetooth Low Energy (BLE) technology and present an algorithm that identifies close contact through analysis and correction of RSSI (Received Signal Strength Indicator) values. Also, propose a system that can prevent the spread of viruses in a centralized server structure.

• Tunnel and Underground Space
• /
• v.31 no.6
• /
• pp.593-609
• /
• 2021

We proposed a numerical method for the thermo-mechanical behavior of rock fracture using a grain-based distinct element model (GBDEM) and simulated thermally induced fracture slip. The present study is the benchmark simulation performed as part of DECOVALEX-2023 Task G, which aims to develop a numerical method to estimate the coupled thermo-hydro-mechanical processes within the crystalline rock fracture network. We represented the rock sample as an assembly of Voronoi grains and calculated the interaction of the grains (blocks) and their interfaces (contacts) using a distinct element code, 3DEC. Based on an equivalent continuum approach, the micro-parameters of grains and contacts were determined to reproduce rock as an elastic material. Then, the behavior of the fracture embedded in the rock was characterized by the contacts with Coulomb shear strength and tensile strength. In the benchmark simulation, we quantitatively examined the effects of the boundary stress and thermal stress due to heat conduction on fracture behavior, focusing on the mechanism of thermally induced fracture slip. The simulation results showed that the developed numerical model reasonably reproduced the thermal expansion and thermal stress increment, the fracture stress and displacement and the effect of boundary condition. We expect the numerical model to be enhanced by continuing collaboration and interaction with other research teams of DECOVALEX-2023 Task G and validated in further study experiments.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.31 no.5
• /
• pp.494-499
• /
• 2011

This paper presents the biomechanical analysis and evaluation technology of musculoskeletal system by multi-body human dynamic model and 3-D motion capture data. First, medical image based geometric model and material properties of tissue were used to develop the human dynamic model and 3-D motion capture data based motion analysis techniques were develop to quantify the in-vivo joint kinematics, joint moment, joint force, and muscle force. Walking and push-up motion was investigated using the developed model. The present model and technologies would be useful to apply the biomechanical analysis and evaluation of human activities.