• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.6
• /
• pp.45-51
• /
• 1995

This paper proposes a CMAC-based controller for servo systems with stick-slip friction. Performance of the controller was evaluated from computer simulations and compared with that of a conventional PID controller. Firction model used in the simulations is based upon the one proposed by Tustin. It was shown that the CMAC-based controller settles more quickly, and overshoots less than the PID. It was also shown that the CMAC is less sensitive to the changes of the plant parameters.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.6
• /
• pp.106-113
• /
• 1997

A new algorithm based upon TDC (Time Delay Control) is proposed to improve the robustness of TDC performance in systems where the stick-slip friction is strong. Experiments were performed at the different levels of friction. The reponses of the TDC and the modified TDC were compared each other, and against those of a PID controller with an anti-windup. The results show that the TDC and the modified TDC equally perform better than the PID, and that the modified TDC performs consistently well even with variations in the friction level while the TDC does not.

• Proceedings of the KIEE Conference
• /
• 2002.07d
• /
• pp.2373-2375
• /
• 2002

전자 제어식 미끄럼 방지 제동 장치(ABS, Anti-lock Brake System)를 장착한 차량의 실차 제동 시험은 시험용 차량을 비롯하여, 많은 분석장비를 필요로 한다. 이러한 고가의 장비는 구하기가 어려울 뿐만 아니라 사용방법을 학습하는 데에도 상당한 기간을 필요로 하므로, 개발중인 ABS에 대하여 적용해 보기에는 그 사용에 제약을 받는다. 본 논문에서는 개발중인 미끄럼방지 제동 알고리즘과 전자제어장치(ECU, Electronic Control Unit)를 대형 버스에 장착하여, 저 점착 노면에서 주행 시험을 시행하였고, 그 주행 기록의 분석을 위하여 DAS(Data Acquisition System)를 구현하였다. 개발 ABS 알고리즘 및 ECU의 기능과 성능 검증이 목적인 DAS는 부가적인 센서 및 고가의 장비를 사용하지 않고 제어보드와 휴대용 노트북 컴퓨터를 이용하였다. 고정밀도의 자료를 획득할 수는 없었지만, 개발 DAS를 이용한 차량 실차 제동 시험은 경제적이면서도 효과적인 ECU 및 알고리즘의 성능 분석을 이룰 수 있었다. 특히 개발 DAS는 제어 및 Data Acquisition을 동일한 보드를 사용하여 구현함으로써, ABS 장착 실차 주행 시험 결과를 제어알고리즘에 즉각적으로 반영시킨 수 있었다. 이러한 One Board System 및 On-Vehicle Programming을 이용한 방법은 개발 알고리즘의 빠른 Debugging 및 파라미터 조정(Tuning)을 가능하게 하였으므로, 실차 제동 시험을 위한 한정된 기간 내에 개발 ABS ECU 및 제어 알고리즘의 성능을 효과적으로 검증할 수 있었다.

• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.5
• /
• pp.565-571
• /
• 2011

Because most fatigue cracks in wheel and rail take place by rolling contact of wheel and rail in railroad industry, it is critical to understand the rolling contact phenomena, especially for the three-dimensional situation. This paper presents an approach to steady-state rolling contact problem of three-dimensional contact bodies, with or without tangential force, based on the finite element method. The steady-state conditions are controlled by the applied relative slip and tangential force. The three-dimensional distribution of tangential traction and contact stresses on the contact surface are investigated. Results show that the distribution of tangential traction and contact stresses on the contact surface varies rapidly as a result of the variation of stick-slip region. The tangential traction is very close in form to Carter's distribution.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.13 no.6
• /
• pp.88-98
• /
• 2014

A moving mass on a skewed linear guideway model to analyze the friction-induced stick-slip behavior of ball-screw-driven slides is proposed. To describe the friction force, a friction coefficient function is modelled as a third-order polynomial of the relative velocity between the slide mass and a guideway. A nonlinear differential equation of motion is derived and an approximate solution is obtained using a perturbation method for the amplitudes and base frequencies of both pure-slip and stick-slip oscillations. The results are presented with time responses, phase plots, and amplitude plots, which are compared adequately with those obtained by Runge Kutta 4th-order numerical integration, as long as the difference between the static and kinematic friction coefficients is small. However, errors in the results by the approximate solution increase and are not negligible if the difference between the friction coefficients exceeds approximately 40% of the static friction coefficient.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.3
• /
• pp.361-367
• /
• 2010

The barrel cam, which is a type of cylindrical cam, has been widely used as a part of index drive units for automatic manufacturing machines. The axis of rotation of the barrel cam is orthogonal to the axis of rotation of the follower. The index drive rotates or dwells depending on the cam profile, while the cam rotates with a constant velocity. Continuous sliding contact between the barrel cam and the follower surfaces causes wearing of the adhesive between them. This study shows that the contact force between two sliding bodies is responsible for the wear of the barrel cam in the paper-cup-forming machine. This contact force is calculated by using the multibody dynamics model of the paper-cup-forming machine. The analytical result is validated by comparing it to the actual wear spots on the real product.