• Journal of the East Asian Society of Dietary Life
• /
• v.21 no.3
• /
• pp.392-400
• /
• 2011

The objectives of this study were to analyze environmental microbial contamination levels by sampling the surfaces of processing lines and equipment and to verify CCPs of the HACCP plan in a fresh-cut produce processing plant The level of airborne microorganisms in the processing plant was $10^1$ log CFU/plate/15min. Total plate counts and coliform groups of the processing facilities were 1~2 log CFU/100 $cm^2$. No E. coli or S. aureus were detected in the processing plant. However, total plate counts on the cutting board for raw materials and on the spin-dryer were $4.20{\pm}2.12$ log CFU/$cm^2$ and $4.57{\pm}0.92$ log CFU/$cm^2$, respectively. These levels were higher than the safe microbial level, and therefore, the chance of cross-contamination during processing was increased. According to the results of microbiological analyses, total aerobic bacteria and coliform groups of the samples were increased after the second washing and spin-drying steps, due to cross-contamination from the spin-dryer. Thus, an effective method that can be used for microbial control during the washing and drying steps is needed for microbial control in fresh-cut produce processing plants. The results of a verification study also suggest that modification of the HACCP plan is needed along with additional CPs, which were identified as a second washing, spin drying, and the cold storage of final products.

• Restorative Dentistry and Endodontics
• /
• v.30 no.2
• /
• pp.79-85
• /
• 2005

The purpose of this study was to evaluate the obturation efficiency of a non-standardized gutta-percha cone in curved root canals prepared with 0.06 taper nickel-titanium instruments. Sixty simulated curved root canals in clear resin blocks were prepared with crown-down technique using 0.06 taper rotary $ProTaper^{TM}$and ProFile (Dentsply-Maillefer) until apical canal was size 30. Root canals were randomly divided into 4 groups of 15 blocks and obturated with cold-laterally compacted gutta-percha technique by using either a non-standardized size medium gutta-percha cone or an ISO-standardized size 30 one as a master cone. Gutta-percha area ratio were calculated at apical levels of 1, 3 and 5 mm using AutoCAD 2000 after cross-sectioning, and the data were analyzed with one-way and two-way ANOVAs and Duncan's multiple range test. Non-standardized size medium cone groups showed significantly higher gutta-percha area ratio than standardized cone groups at all apical levels (p < 0.01). Non-standardized cone groups used significantly less accessory cones than standardized cone groups (p < 0.01).

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.88-88
• /
• 2017

감자 재배 기계화를 위한 전자동 감자 파종기의 기구적인 개념 설계를 수행하고, 시작기를 제작하였다. 시작기의 성능평가를 통해 기계화에 적합한 감자 재배양식에 대한 연구 필요성이 대두되었다. 본 연구의 목적은 감자 재배 양식에 따른 주요 감자의 생육 사항, 수량성, 상품성 및 품질, 주요 생리 장애등을 측정하여 기계파종 후 재배상의 문제점 파악과 파종 시 기계적인 미비점을 파악하여 개선방안을 마련하는데 있다. 기존의 국내 관행적 감자 재배 작형별 재배방식은 1줄 재배의 경우 재배 형식이 둥근두둑 방식이며, 2줄 재배의 경우 평두둑 방식을 채택하고 있다. 감자 파종기를 이용한 기계화 재배의 경우 평두둑으로 2줄 재배 방법을 채택하였다. 본 연구는 공시품종인 수미를 이용하여 봄 재배 형식으로 강릉 재배단지에서 실시하였다. 감자 파종은 2016년 3월 31일에 실시하였으며, 재배기간 92일을 소요하여 수확은 2016년 6월 30일에 하였다. 기계파종의 경우 두둑형식은 평두둑 2줄 재배양식 흑색비닐(파종구 세절) 파종 방법으로 전자동 기계파종을 실시하였고, 인력 파종의 경우 기계 파종과 동일한 방식으로 인력으로 실시하였다. 기존의 재래적 방식인 관행파종은 두둑형식은 외줄 1줄 흑색비닐(유공) 파종 방법으로 인력파종을 실시하였다. 관행 파종 방법은 이랑사이 75-80cm, 주간거리 20-25cm, 흙덮기 8-12cm로 재식밀도는 5,000-5,300주/10a로 씨감자 160kg/10a 소요하여 파종하였다. 실험 결과 감자 파종방법별 출현율은 기계파종의 경우 79.9-88.4%, 인력파종의 경우 97.9-99.2%로 기계파종에서 인력파종대비 결주율이 10.0-18.5% 정도 발생되었다. 씨감자의 절단 방법은 4절에 비하여 2절에서 양호하였다. 상품 지수의 경우 관행파종을 기준(100)으로 기계 파종(90)과 인력 파종(103)은 4절로 작업한 곳에서 상품성이 높았다. 파종 전 싹틔우기 여부에 따라서는 생육 초기(30일 이전)에는 싹틔운 파종 방법이 양호하였으나, 생육 후기(30일 이후)에는 싹을 틔우지 않은 파종 방법이 양호하였다. 기계 파종을 이용한 4절 씨감자 파종은 부패율이 12.2%로 다른 대비군에 비해 높았다(1.9-7.6%). 수확량(kg/10a)은 기계파종에서 2,748-3,503 kg 으로 관행 3,883 kg 대비 71-90% 수준으로 나타났다. 싹틔우지 않은 감자 4절을 이용한 기계 파종 시 결주율이 18.5%, 부패율 12.2%으로 싹틔운 감자 2절을 이용한 기계 파종으로 할 경우 결주율 10%, 부패율 4.1% 으로 낮출 수 있다.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.20 no.4
• /
• pp.300-307
• /
• 1987

The present study was investigated on the DNA damage by the peroxidation of polar and non-polar lipid fractionated from mackerel lipid to elucidate the DNA damage mechanism by fish oil peroxidation. The degree of DNA damage by polar lipid peroxidation became greater with the increase of its concentration, and such DNA damage was induced below 100 millieq./kg in POV for 4 days incubation. Among the polar lipid peroxidation products, singlet oxygen $^1O_2$ and superoxide anion ${\cdot}O_2^-$ greatly affected to the DNA damage than hydrogen peroxide $H_2O_2$ and hydroxyl radical ${\cdot}OH$. Non-polar lipid peroxidation also induced the DNA damage with the increase of its concentration, but such effect was lower than the case of total lipid and polar lipid. And, the effects of active crygens on the DNA damage by non-polar lipid peroxidation was the same as in the case of total and polar lipid peroxidation.

• Clean Technology
• /
• v.23 no.2
• /
• pp.196-204
• /
• 2017

CdZnS/ZnO composite was prepared through low-temperature precipitation and drying method. The property of CdZnS/ZnO as a recyclable photocatalyst for the degradation of rhodamine B (RhB) under visible light irradiation was examined. The sample was characterized by XRD, FE-SEM, XPS, UV-vis DRS and photoluminescence techniques before and after repeated reaction to investigate the change of properties during the photocatalytic reaction. During repeated reaction, the CdZnS/ZnO showed an improved photocatalytic activity and recycle stability. Among two feasible reaction pathways for photocatalytic degradation of RhB, the cleavage of conjugated chromophore was found to predominate over N-dealkylation of chromophore skeleton in the present work. The results indicate that the CdZnS/ZnO, prepared by a simple precipitation method, can be used as a visible-light driven photocatalyst with enhanced cycle stability and activity.

• Journal of Energy Engineering
• /
• v.13 no.4
• /
• pp.281-290
• /
• 2004

Spent refractories from a coal gasifier after 1000 hours of operation were analyzed for crystalline phases, chemical composition and microstructures as a function of slag penetration depth, and the slag corrosion mechanism was determined. The chemical corrosion of chromia refractory occurred via reaction between Cr$_2$O$_3$ of the refractory and FeO and A1$_2$O$_3$ in the slag. The FeO reacted with Cr$_2$O$_3$ at the slare/refractory interface and formed FeCr$_2$O$_4$. After all FeO were consumed, Al in the penetrating slag substituted Cr in Cr$_2$O$_3$, forming (Al, Cr)$_2$O$_3$, at the edges of the particle, which were broken to form fragments rich in Al. The corrosion resistance of Cr$_2$O$_3$ varied with the particle size and the extent of sintering, and the higher resistance was observed in the larger and more sintered particles. There was no chemical change in ZrO$_2$, but showed the effects of physical corrosion: the grain boundaries became more wavy, and ZrO$_2$ grains were split in the corroded area. The slag penetration depth increased in the refractory samples farther down from the feed nozzles.

• Resources Recycling
• /
• v.14 no.5 s.67
• /
• pp.13-17
• /
• 2005

As a basic study for recycling molten converter slag as an ordinary portland cement (OPC) by a conversion process, the reaction mechanism and the rate of the formation of $C_4AF$ which is one of the main components of OPC were investigated. The converter slag whose basicity was controlled by adding reagent grade $SiO_2$ was melted and hold for 30 minutes in MgO crucible at $1300^{\circ}C{\sim}1350^{\circ}C$. Then, the sintered CaO pellet heated at the same temperature was dipped into the molten slag and hold for $10{\sim}30$minutes. After the reaction, the crucible was cooled in air and the specimen was cut off to the horizontal direction of the crucible. The dissolution rate of $C_3A$ pellet was measured by the change of radius of the sintered $C_3A$ pellet, and the formed phase of $C_4AF$ was observed by SEM/EDX. As a result, the dissolution rate of $C_3A$ pellet into molten slag was increased from $0.75{\times}10^{-4}(cm/sec)$ at $1300^{\circ}C$ to $1.67{\times}10^{-4}(cm/sec)$ at $1350^{\circ}C$, and the mixed layer of $C_4AF$ and $C_{12}A_7$ was found between slag and $C_3A$ pellet.

• Korean journal of food and cookery science
• /
• v.23 no.5
• /
• pp.650-663
• /
• 2007

The purpose of this study was to identify the sanitation management items of school foodservice suppliers that require improvement, by assessing their sanitation practices with food commodities. Our field assessment was performed using a total of 20 vendors supplying agricultural products, meat products, seafoods and processed products; all were located in the Seoul and Gyeonggi areas. The assessment tool for sanitation management was composed of 93 checklist items and was used to evaluate seven different categories; the facility and environment, management of the facility and equipment, food materials management, process control, water management, personal hygiene management, and laboratory instrument management. A score of two was given for "satisfactory", one for "fair", and zero for "unsatisfactory". The overall average supplier score was 1.7/2.0 (85.8%). The score of the seafood vendors was highest at 1.9 (95.4%), while the lowest score of 1.3 (65.7%) occurred with the processed product suppliers. Among the sanitation management categories, water management was scored at 2.0, while inspection management was lowest at 1.4. The subcategories indicating needed improvements for the processed product suppliers were raw materials, storage, transport and recall. For the agricultural product suppliers it was preparation management. furthermore, one item within the laboratory instrument management category was unsatisfactory for both the agricultural and processed product suppliers. In conclusion, these results can be used to develop sanitation management procedures for suppliers, as well as by administration agencies to evaluate and guide those suppliers.

• Restorative Dentistry and Endodontics
• /
• v.32 no.6
• /
• pp.522-529
• /
• 2007

The purpose of this study was to compare the apical leakage of the root canal filled with the System B and the EndoTwinn(the combined application of heat and ultrasonic vibration). Sixty extracted premolars with straight root were cleaned and shaped to size 35. Group SB was obturated using System B and Group ET was filled with EndoTwinn. A size 35 of 0.06 tapered gutta-percha and Adseal were used and the plugger which could be introduced to 4 mm short of working length was selected in the obturation procedure. As the positive control, Group PC was not filled. In Group SB, ET and PC, all external surfaces of each tooth were coated with nail varnish leaving only 1 mm area around the apical foramen. In the negative control of Group NSB and Group NET, all of external tooth surface including apical foramen was coated with the nail varnish. The specimens were immersed in methylene blue dye solution for 2 days. Then the specimens were sectioned at each 1 mm from apex to 5 mm level. The final score of one specimen was given by summing up of the points at all levels. The dye leakage of Group ET was significantly less than that observed in Group SB (p < 0.05). And the frequency of gutta-percha pulling out from root canal when the plugger was removed was more often with the System B than with EndoTwinn but there was no significant difference.

• International Journal of Highway Engineering
• /
• v.9 no.4
• /
• pp.117-127
• /
• 2007

The exposed aggregate PCC(EAP) pavements have been successfully used in Europe and Japan as low-noise pavements. Coarse aggregate are exposed on the pavement surface texture of EAP by removing mortar of surface. The pavement surface texture should maintain not only low-noise characteristic but also adequate skid resistance level during the performance period. Skid resistance decreased with wearing and polishing of tire and pavement surface due to the repetition of tire-pavement contact. Since the tires mainly contact the exposed coarse aggregate, the shape and rock type of coarse aggregate significantly influence wearing and polishing of EAP pavements. The test for resistance to abrasion coarse aggregate by use of the Los Angeles machine(KS F 2508) and the method of test for resistance to abrasion coarse aggregate by use of the Accelerated Polishing Machine(ASTM D 3319-90) are generally used to evaluate polishing characteristics of aggregate. In this study, polishing of coarse aggregate of different five rock types were evaluated by KS F 2508(LA abrasion test) and ASTM D 3319-90(PSV method). The results of LA abrasion test and PSV method were contrary to each other. Since LA abrasion test is estimated the quantity of abrasion by the impact of aggregate, it may not be adequate to evaluate the polishing of aggregate by the repetition of tire. In the case of PSV method, the resistance of polishing is estimated the skid resistance variation of polished aggregate after repetition of tire. The PSV method is adequate for the evaluation on polishing of coarse aggregate. From the test results of PSV method, it was founded that rock type, specific gravity, coarse aggregate angularity, flat or elongated particles in coarse aggregate are significant to the resistance characteristic of coarse aggregate.