• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2009.05a
• /
• pp.733-736
• /
• 2009

Power Line Communication(PLC) is need not additional communication line. So establishment expense is inexpensive and application is simple. Therefore, lower part network of various application field is possible. However, there are high subordinate interference and noise problem on limited transmission data and communication interference element. Wireless Sensor Network(WSN) is need not infrastructure, Self-regulating network architecture of sensor nodes is possible. So at short time, network construction is available. But, power consumption is increased by active sensing for QoS elevation and unnecessary information transmission, low electric power design and necessity of improve protocol are refered to life shortening problem and is studied. In this paper, supplement problem of power line communication and wireless sensor network mutually and because advantage becomes linkage integration control system using synergy effect of two technologies as more restriction be and tries to approach structurally control network that is improved for smooth network environment construction. Honeywell's hybrid sensor network does comparative analysis(benchmarking). Confirm performance elevation proposing teaming of power line communication and wireless sensor network. Through simulation, service delay decreases and confirms that performance elevation.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2004.04a
• /
• pp.5-9
• /
• 2004

In this paper, we studied the OCT(Optical Coherence Tomography) system which it has been extensively studied because of having some advantages such as high resolution cross-sectional images, low cost, and small size configuration. A basic principle of OCT system is Michelson interferometer. The characteristics of light source determine the resolution and the transmission depth. As a results, the light source have a commercial SLD with a central wavelength of 1,285 nm and FWHM(Full Width at Half Maximum) of 35.3 nm. The optical delay line part is necessary to equal of the optical path length with scattered light or reflected light from sample. In order to equal the optical path length, the stage which is attached to reference mirror is moved linearly by step motor And the interferometer is configured with the Michelson interferometer using single mod fiber, the scanner can be focused of the sample by using the reference arm. Also, the 2-dimensional cross-sectional images were measured with scanning the transverse direction of the sample by using step motor. After detecting the internal signal of lateral direction at a paint of sample, scanner is moved to obtain the cross-sectional image of 2-demensional by using step motor. Photodiode has been used which has high detection sensitivity, excellent noise characteristic, and dynamic range from 800 nm to 1,700 nm. It is detected mixed small signal between noise and interference signal with high frequency After filtering and amplifying this signal, only envelope curve of interference signal is detected. And then, cross-sectional image is shown through converting this signal into digitalized signal using A／D converter. The resolution of the OCT system is about 30$\mu\textrm{m}$ which corresponds to the theoretical resolution. Also, the cross-sectional image of ping-pong ball is measured. The OCT system is configured with Michelson interferometer which has a low contrast because of reducing the power of feedback interference light. Such a problem is overcomed by using the improved inteferometer. Also, in order to obtain the cross-sectional image within a short time, it is necessary to reduce the measurement time for improving the optical delay line.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.48 no.6
• /
• pp.18-26
• /
• 2011

Debates concerning the competitive edge of leading 3DTV technology of the shutter glasses (SG) 3D and the film-type patterned retarder (FPR) are flaring up. Although SG technology enables Full-HD 3D vision, it requires complex systems including the sync transmitter (emitter), the sync processor chip, and the LCD lens in the active shutter glasses. In addition, the transferred sync-signal is easily affected by the external noise and a 3DTV viewer may feel flicker-effect caused by cross-talk of the left and right image. The operating current of the sync processor in the 3DTV active shutter glasses is gradually increasing to compensate the sync reconstruction error. The proposed chip is a low-power hardware sync processor based discrete-event SoC(system on a chip) designed specifically for the 3DTV active shutter glasses. This processor implements the newly designed power-saving techniques targeted for low-power operation in a noisy environment between 3DTV and the active shutter glasses. This design includes a hardware pre-processor based on a universal edge tracer and provides a perfect sync reconstruction based on a floating-point timer to advance the prior commercial 3DTV shutter glasses in terms of their power consumption. These two techniques enable an accurate sync reconstruction in the slow clock frequency of the synchronization timer and reduce the power consumption to less than about a maximum of 20% compared with other major commercial processors. This article describes the system's architecture and the details of the proposed techniques, also identifying the key concepts and functions.

• Journal of the Korean Vacuum Society
• /
• v.21 no.5
• /
• pp.264-272
• /
• 2012

In this paper, we report THz generation and detection characteristics investigated by InGaAs semiconductor epilayers, as results of a basic study obtained from the InGaAs-based THz transmitter/receiver (Tx/Rx). High-temperature and low-temperature (LT) grown InGaAs epilayers were prepared by the molecular beam epitaxy technique for the characterization of THz generation and detection, respectively, and the surface emission based on the photo-Dember effect was tried for THz generation. THz wave was generated by irradiation of a Ti:Sapphire fs pulse laser (60 ps/83 MHz), and a LT-GaAs Rx was used for the THz detection. The frequency band shown in the spectral amplitudes Fourier-transformed from the measured current signals was ranging in 0.5~2 THz, and the signal currents were exponentially increased with the Tx beam power. The THz detection characteristics of LT-InGaAs were investigated by using an Rx with dipole (5/20 ${\mu}m$) antenna, and the cutoff frequency was ~2 THz.

• Journal of Broadcast Engineering
• /
• v.14 no.6
• /
• pp.796-806
• /
• 2009

SVC (Scalable Video Coding) is a new video coding standard to provide convergence media service in heterogeneous environments with different networks and diverse terminals through spatial-temporal-quality combined flexible scalabilities. This paper presents the performance analysis on packet loss in the delivery of SVC over IP networks and an efficient adaptation method to packet loss caused by buffer overflow. In particular, SVC with MGS (Medium Grained Scalability) as well as spatial and temporal scalabilities is addressed in the consideration of packet-based adaptation since finer adaptation is possible with a sufficient numbers of quality layers in MGS. The effect on spatio-temporal quality due to the packet loss of SVC with MGS is evaluated. In order to minimize quality degradation resulted by packet loss, the proposed adaptation of MGS based SVC first sets adaptation unit of AU (Access Unit) or GOP corresponding to allowed delay and then selectively discards packets in order of importance in terms of layer dependency. In the experiment, the effects of packet loss on quantitative qualities are analyzed and the effectiveness of the proposed adaptation to packet loss is shown.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.46 no.3
• /
• pp.244-250
• /
• 2018

Multilateration acquires the transponder signal of target from receivers installed on the ground and calculates the position of the target using the difference of the signal acquisition time of each receiver. One of the factors that influence the positioning accuracy of Multilateration using the TDOA calculation method is the error due to the precision measurement of signal input time. When measuring the signal input time at the receiver, the input signal is sampled using the reference clock of the receiver and a reference sample having the same sampling rate is applied to the cross correlation technique. Therefore, the accuracy of the signal input time is proportional to the reference clock. In this paper, the algorithm for precisely measuring the signal input time by performing cross correlation between the input signal of the receiver and DRS(Delayed Reference Sample) is proposed. In order to verify this, we implemented the pulse signal of the transponder that is transmitted from the target using Matlab. Through the simulation, cross correlation between the proposed DRS and the input signal was performed. From this result, the performance of the precise measurement of signal input time was analyzed.

• The KIPS Transactions:PartD
• /
• v.9D no.6
• /
• pp.1017-1024
• /
• 2002

According as mobile computing environment is generalized by development of wireless networking technology and communication device, mobile host uses local cache for extensibility and early response time. and reduction of limited bandwidth. This time, between mobile host and mobile support station cache need consistency interested person of done data accordingly much techniqueses propose. Existent consistency techniques because detection based techniqueses are used mainly and broadcast periodic invalid message considering frequent disconnection. However, these techniqueses increase abort step through increase or delay of transmission message number by accuracy examination of data. Therefore, because mobile host deletes cached data, and extensity are decreased. Techniques that is proposed in this paper did to perform refering update frequency about object that page request or when complete update operation happens to solve these problem. Therefore, have advantage that response is fast because could run write intention declaration or update by update frequency electively asynchronously when update operation consists and abort step decreases. Also, improved extensity running delete or propagation electively according to update frequency about periodic invalid message gone since disconnection.

• Journal of KIISE:Information Networking
• /
• v.34 no.5
• /
• pp.348-359
• /
• 2007

The conventional mobile VPN services assumed the mobile communications occur between the MN in foreign networks and the CN in the home network. However, if a MN wants to communicate with another MN in a foreign network, it could degrade the performance of the mobile VPN service because of the triangular routing problem. In this paper, we propose a route optimization mechanism based on the mobile VPN using an x-HA allocated by diameter MIP in order to support the efficient communication between the mobile VPN users in foreign networks. The i-HA maintains the VPN-TIA as well as the x-HoA as the CoAs to solve the security problem and to provide an efficient route optimization simultaneously. Moreover, we proposed revised IPSec tunnel configuration to reduce the IPSec tunnel overheads at a MN when the MN communicates with several MNs in the foreign networks at the same time. The VPN server, a security management entity in the home network, notifies an additional IPSec tunnel establishment between the x-HAs where the communication peers are registered. The simulation result showed that the proposed scheme decreases the end-to-end packet delay time and improves the throughput after the handoff compared to the existing mechanism.

• Journal of Korea Spatial Information System Society
• /
• v.1 no.2 s.2
• /
• pp.21-31
• /
• 1999

In accordance with the completion of the spatial database building works in the central and/or local government authorities as well as the rapid popularization of various information services through internet, it is heavily required to provide spatial information services through World Wide Web. To provide a qualified spatial information service, it is crucial to have a Web-based GIS (Geographic Information Service) service system equipped with the publicity, the convenient accessibility, and the easy-to-use user interface. In this paper, we introduce a new component system for Web-based spatial information services based on the OpenGIS Simple Feature specification for OLE/COM[3] and OLE DB specification[4]. The important functionality of a Web-based spatial information service system includes its accessibility of various existing GIS server system and huge databases in addition to the resolution of response-time delay problems caused by transmitting a large amount of digital maps via internet[6]. To cope with these problems, our component system has been designed to access heterogeneous databases in transparent manner and to support vector-based and/or image-based image production techniques for shortening transmission time.

• The KIPS Transactions:PartD
• /
• v.10D no.4
• /
• pp.591-602
• /
• 2003

Delay and discontinuance phenomenon of service are cause by sudden increase of the network communication amount and the quantity consumed of resources when Internet users are driven excessively to a conventional single large database sewer. To solve these problems, spatial database cluster consisted of several single nodes on high-speed network to offer high-performance is risen. But, research about spatial join operation that can reduce the performance of whole system in case process at single node is not achieved. So, in this paper, we propose efficient parallel spatial join processing method in a spatial database cluster system that uses data partitions and replications method that considers the characteristics of space data. Since proposed method does not need the creation step and the assignment step of tasks, and does not occur additional message transmission between cluster nodes that appear in existent parallel spatial join method, it shows performance improvement of 23% than the conventional parallel R-tree spatial join for a shared-nothing architecture about expensive spatial join queries. Also, It can minimize the response time to user because it removes redundant refinement operation at each cluster node.